Performance evaluation of functionalized ordered mesoporous silica for VOCs adsorption by molecular dynamics simulation

Volatile organic compounds (VOCs) are growing pollutants now that cause the serious environmental pollution and threaten human health. The functionalized ordered mesoporous silica (FOMS) has attracted considerable attention in adsorbing VOCs. In this paper, the molecular dynamics simulation was used to simulate the adsorption performance of FOMS on VOCs (acetone, ethyl acetate and toluene). After simulating different pore sizes (2 nm, 3 nm and 4 nm) adsorption performances of ordered mesoporous silica (OMS) on VOCs, OMS with a pore size of 4 nm was selected to further study the influence of functional groups (vinyl, methyl, and phenyl). The following law was obtained: the saturated adsorption capacities of vinyl-functionalized OMS (V-FOMS) to acetone, ethyl acetate and toluene were 3.045 mmol.g^?1, 2.568 mmol.g^?1 and 1.976 mmol.g^?1 respectively; the saturated adsorption capacities of methyl-functionalized OMS (M-FOMS) to acetone, ethyl acetate and toluene were 2.798 mmol.g^?1, 2.312 mmol.g^?1 and 1.698 mmol.g^?1 respectively; the saturated adsorption capacities of phenyl-functionalized OMS (P-FOMS) to acetone, ethyl acetate and toluene were 2.124 mmol.g^?1, 1.941 mmol.g^?1 and 1.539 mmol.g^?1 respectively. These results show that the adsorption ability of FOMS for different adsorbates follows the sequence of acetone > ethyl acetate > toluene. Furthermore, the interaction between functional groups (vinyl, methyl and phenyl) in FOMS and VOCs was explored. It is found that the interaction between different functional groups and adsorbates is different (interaction energy effect). This interaction energy effect promotes FOMS to better adsorb VOCs. This work would provide fundamental understanding and guidance for the development of novel adsorption materials for the adsorption of VOCs.     

溅射参数对ZnO薄膜物性的影响

采用磁控溅射方法分别在ITO玻璃和硅片上成功制备了具有良好C轴取向的ZnO薄膜.并研究了溅射气压,基底温度,以及氧偏压对ZnO薄膜物性的影响,从而确定了制备ZnO薄膜的最佳溅射条件.     

Relationships among Preparative Technique,Phase Composition and Bending Strength of Bauxite Porcelain

1 INTRODUCTION Bauxite porcelain is a novel “K2O–Al2O3–SiO2” system ceramic by using sintered bauxite, clay and potash feldspar and albite as the main raw materials with the Al2O3’s content of 50%～60(massfraction). Compared to the traditional“K2O–Al2O3–SiO2” feldspar porcelain by using quartz, bolus alb and potash feldspar and albite as the main raw materials, the bauxite porcelain possesses such advantages as high mechanical strength, excellent electrical insula- tion prop…     

Evolution of Er^3＋ Distribution in the Oxyfluoride Glass Ceramics with Heating

The distribution characteristics of Er3+ ions doped in the oxyfluoride glass ceramics containing LaF3 nanocrystals heat-treated at 650 ℃ for different durations were investigated. The results of the integral absorption cross-section analysis demonstrated that the partition fraction of Er3+ in LaF3 nanocrystals increases with prolonging of heating time. The anomalous phenomena of Er3+ emissions in the up-and the down-conversion fluorescence spectra are well explained based on the calculated results.     

Ti-Si复氧化物载体对金催化剂上丙烯环氧化的影响

 以TiCl4和SiCl4为原料,采用水解和非水水解溶胶-凝胶两种方法制备了一系列不同Ti含量的Ti-Si复氧化物载体,继而用沉积-沉淀法制得载金催化剂. 采用X射线衍射、紫外-可见漫反射光谱、 N2吸附和高分辨透射电镜对催化剂进行了表征,并考察了催化剂在氢气和氧气存在下的丙烯气相环氧化催化性能. 研究表明,钛含量在6%～14%范围内时,两种方法制得的Ti-Si复氧化物均为无定形结构,但采用非水水解溶胶-凝胶法制得的载体比表面积较高. 以非水水解溶胶-凝胶法制备的钛含量10%的Ti-Si复氧化物为载体得到的载金催化剂表现出较高的活性和选择性,反应60 min时,丙烯转化率为5.7%, 240 min后降为3.3%, 环氧丙烷的选择性稳定于95%左右. 还考察了非水水解溶胶-凝胶的陈化时间和金沉积-沉淀溶液的pH值等对反应结果的影响.     

MnCl2-H4SiW12O40/SiO2催化氧化二甲醚制取甲缩醛

 采用浸渍法制备了H4SiW12O40/SiO2杂多酸催化剂,分别使用MnCl2, SnCl4和CuCl2对其进行修饰,并在常压连续流动固定床反应器中考察了催化剂对二甲醚选择氧化制取甲缩醛的催化活性. 结果表明, MnCl2修饰的H4SiW12O40/SiO2催化剂的活性和甲缩醛选择性均高于SnCl4和CuCl2修饰的催化剂. 进一步考察了不同MnCl2含量及反应温度对反应的影响. 在MnCl2含量为5%, 反应温度为593 K时, MnCl2-H4SiW12O40/SiO2催化剂的活性和甲缩醛选择性最佳,二甲醚转化率为8.6%, 甲缩醛选择性为36.3%. X射线衍射结果显示, MnCl2与H4SiW12O40相互作用并均匀地分散在载体上. 用红外光谱研究了MnCl2-H4SiW12O40/SiO2催化剂的结构,发现改性后的催化剂基本保持了杂多酸的Keggin结构. NH3程序升温脱附结果显示, MnCl2的加入较明显地降低了催化剂的酸强度和酸中心数目.     

羧基丁苯-纳米氧化硅复合粉末增韧聚苯乙烯的研究

用直接分散聚合法制备了羧基丁苯-纳米氧化硅杂化胶乳,经喷雾干燥得到的羧基丁苯-纳米氧化硅复合粉末通过本体-悬浮聚合和熔融共混法制备了高抗冲聚苯乙烯.结果表明,本体/悬浮聚合法中预聚转化率的控制与复合粉末的加入量有关,当加入的复合粉末的质量分数为0.05时,冲击强度可提高5倍,也高于熔融共混法所制备的改性聚苯乙烯.本体/悬浮聚合法制备的改性聚苯乙烯的热分解温度（Td）高于熔融共混法改性的,且Td随复合粉末加入量的增加而提高,但改性聚苯乙烯的刚性有一定程度的降低,而对材料的玻璃化转变温度影响不大.     

NARROW-DISPERSED CROSSLINKED CORE-SHELL POLYMER MICROSPHERES PREPARED BY SURFACE-INITIATED ATOM TRANSFER RADICAL POLYMERIZATION＊

Grafting of polystyrene with narrowly dispersed polymer microspheres through surface-initiated atom transfer radical polymerization (ATRP) was investigated. Polydivinylbenzene (PDVB) microspheres were prepared by dispersion polymerization with poly(N-vinyl pyrrolidone) (PVP) as stabilizer. The surfaces of PDVB microspheres were chloromethylated by chloromethyl methyl ether in the presence of zinc chloride as catalyst to form chloromethylbenzene initiating core sites for subsequent ATRP grafting of styrene using CuCl/bpy as catalytic system. Polystyrene was found to be grafted not only from the particle surfaces but also from within a thin shell layer, resulting in the formation of particles size increased from 2.38-2.58μm, which can further grow to 2.93μm during secondary grafting polymerization of styrene. This demonstrates that grafting polymerization proceeds through a typical ATRP procedure with living nature. All of the prepared microspheres have narrow particle size distribution with coefficient of variation around 10%.     

MICRO-PHASE SAEPARATION IN EPOXY RESIN WATERBORNE PARTICLES DURING CURING PROCESS

Sub-micron sized phenolic epoxy resin waterborne particles were prepared by phase inversion emulsification. Micro-phase separation occurred during the curing process at high temperature. The as-prepared samples possessed one glass transition temperature （Tg） and two exothermal processes during DSC heating scannings. After being thermally treated above the exothermal peak temperature, they possessed two glass transition temperatures with the disappearance of exothermal peaks, whilst a core/shell structure was formed. This was likely related with the outward diffusion of reactive oligomers to the outer layer of particles.