Upconversion luminescence of Tm^3＋/Yb^3＋ codoped oxyfluoride glasses

Novel oxyfluoride glasses are developed with the composition of 30SiO2-15Al2O3-28PbF2-22CdF2-0.1TmF3 - xYbF3 - （4.9 - x） AlF3（x=0, 0.5, 1.0, 1.5, 2.0） in tool fraction, Furthermore, the upconversion luminescence characteristics under a 970nm excitation are investigated. Intense blue, red and near infrared luminescences peaked at 453nm, 476nm, 647nm and 789nm, which correspond to the transitions of Tm^3＋： ^1D2 →^3F4, ^1G4 →^3H6, ^1G4 →^3F4, and ^3H4 →^3H6, respectively, are observed. Due to the sensitization of Yb^3＋ ions, all the upconversion luminescence intensities are enhanced considerably with Yb^3＋ concentration increasing. The upconversion mechanisms are discussed based on the energy matching rule and quadratic dependence on excitation power. The results indicate that the dominant mechanism is the excited state absorption for those upconversion emissions.     

掺Eu3+硅基材料的发光性质

通过溶胶－凝胶技术制备了掺Eu^3 的硅基材料并测试了其三维荧光光谱、激光谱和发射光谱，结果显示，最佳激发波波长为350nm,最强荧光波长为620nm；在350nm光激发下的发射光谱显示Eu^3 的特征发射光谱，产生4条谱带，分别是577nm(^5D0-^7F0)，588nm(^5D0-^7F1),596nm(^5D0-^7F1)和610nm(^5D0-^7F2)。     

0.18μm CMOS工艺栅极氧化膜可靠性的衬底和工艺依存性

用斜坡电压法(Voltage Ramp, V-ramp)评价了0.18μm双栅极 CMOS工艺栅极氧化膜击穿电量(Charge to Breakdown, Q_bd)和击穿电压(Voltage to Breakdown, V_bd). 研究结果表明，低压器件(1.8V)的栅极氧化膜(薄氧)p型衬底MOS电容和N型衬底电容的击穿电量值相差较小，而高压器件(3.3V)栅极氧化膜(厚氧)p衬底MOS电容和n衬底MOS电容的击穿电量值相差较大，击穿电压测试值也发现与击穿电量 关键词： 薄氧 可靠性 击穿电压 击穿电量     

射频磁控溅射法制备薄膜电池电极的计算机模拟初步

计算机模拟仿真射频磁控溅射实验制备薄膜及离于电池电极,研究了在特定实验条件下薄膜的生长过程,并分析了影响薄膜生长的部分因素。     

The effect of ITO films thickness on the properties of flexible organic light emitting diode

Indium tin oxide (ITO) thin films were deposited on cyclic olefin copolymer substrate at room temperature by an inverse target sputtering system. The crystal structure and the surface morphology of the deposited ITO films were examined by X-ray diffraction and atomic force microscopy, separately. The electrical properties of the conductive films were explored by four-point probing. Visible spectrometer was used to measure the optical properties of ITO-coated films. The performance of the flexible organic light emitting diode device with different thickness anode was investigated in this study.     

彩色透明微晶玻璃的吸收光谱

在Li2O-Al2O3-SiO2系统玻璃中掺入少量晶核剂TiO2,ZrO2,P2O5，再掺入稀土离子和过渡金属离子作为着色剂，在高温下溶制得到彩色透明玻璃，对上述玻璃进行微晶化处理，用差热分析（DTA）确定其晶化温度，测定与讨论了所获彩色透明微晶玻璃在紫外波段至近红外波段的吸收光谱特性，研究结果表明，玻璃微晶化后，由于基质玻璃对光的微弱散射，引起吸收的增强，但不改变稀土离子和过渡金属离子的本征吸收峰位。     

溶胶-凝胶VO2薄膜转换特性研究

利用溶胶凝胶法在SiO2Si衬底上沉积高取向的V2O5薄膜,在压强低于2Pa,温度高于400℃的条件下,对V2O5薄膜进行真空烘烤,获得了电阻率变化3个数量级以上、弛豫宽度为62℃的VO2多晶薄膜.以X射线衍射(XRD)、扫描电子显微镜(SEM)图和电阻率转换特性等实验结果为依据,详细分析了溶胶凝胶薄膜在真空烘烤时从V2O5向VO2的转化,它经历了从VnO2n+1(n=2,3,4,6)到VO2的过程.实验证明,根据选择合适的成膜热处理条件和真空烘烤条件是实现溶胶凝胶V2O5结构向VO2结构成功转换的关键 关键词： 溶胶-凝胶法 氧化钒薄膜 VO2膜转换特性     

Optical current transducers using flint glass fiber as the faraday sensor element

This paper describes development of the optical current transducers using flint glass fiber as the Faraday effect sensing element. Excellent polarization properties of the fiber with low birefringence are described, and the design and test data of a current transducer using the fiber manufactured for use in electric power facilities are reviewed. Experimental results on flexible characteristics of a scheme with round trip light transmission in the fiber is also reported.     

高温超导薄膜微波非线性研究的进展

文章介绍了高温超导薄膜微波非线性的主要特征，阐述了高温超导薄膜微波非线性产生的原因和相关的研究现状，指出了高温超导薄膜非线性研究中遇到的困难和尚未解决的问题．     

Modeling of environmentally significant interfaces: Two case studies

When some parameters cannot be easily measured experimentally, mathematical models can often be used to deconvolute or interpret data collected on complex systems, such as those characteristic of many environmental problems. These models can help quantify the contributions of various physical or chemical phenomena that contribute to the overall behavior, thereby enabling the scientist to control and manipulate these phenomena, and thus to optimize the performance of the material or device. In the first case study presented here, a model is used to test the hypothesis that oxygen interactions with hydrogen on the catalyst particles of solid oxide fuel cell anodes can sometimes occur a finite distance away from the triple phase boundary (TPB), so that such reactions are not restricted to the TPB as normally assumed. The model may help explain a discrepancy between the observed structure of SOFCs and their performance. The second case study develops a simple physical model that allows engineers to design and control the sizes and shapes of mesopores in silica thin films. Such pore design can be useful for enhancing the selectivity and reactivity of environmental sensors and catalysts. This paper demonstrates the mutually beneficial interactions between experiment and modeling in the solution of a wide range of problems.