东太平洋深海锰结核的化学元素研究

用ICP-AES法测定了东太平洋深海锰结核样品中二十多种主，次及微量元素，结果表明，表面瘤状和表面光滑两种类型锰结核的化学元素含量有较明显的区别，如表面光滑的锰结核TiO2含较高，而表面瘤状的锰结核Mn/Fe之值较高等。     

Chemical environment of copper at the surface of a CuAl2 model alloy: XPS,MEIS and TEM analyses

Air‐formed oxide on a CuAl₂ model alloy is shown to be free of copper species, with copper enriching in the alloy. With thickening of the oxide by anodizing, copper enriches further to a critical concentration at which its oxidation proceeds with incorporation of Cu(II) species into the film. Such species migrate more rapidly through the film than aluminium species. Incorporation of copper species is associated with generation of oxygen gas within the film and subsequent film rupture is due to release of the gas. Reduction of Cu(II) to Cu(I) species during XPS analysis is characterized and the accelerating role of charge neutralizing is highlighted. Copyright © 2004 John Wiley & Sons, Ltd.     

富镧混合稀土对ZL101A合金组织和机械性能的影响

研究了富镧混合稀土对ＺＬ１０１Ａ合金的铸态、固溶态、Ｔ６状态、重熔态的组织和机械性能的影响，提出了混合稀土中入量低压铸造整体车轮合理的热处理状态。     

Selenium in electrolytic manganese as a reference material for the quality control of aluminium melts

Electrolytic manganese is an important alloying element for aluminium and steel melts. It is mainly added to melts of aluminium in the holding furnace as tablets or minitablets (compressed compacts of manganese and aluminium powders). Selenium derivates are usually added during the production of electrolytic manganese, so some selenium is present in the alloys produced when electrolytic manganese is added to the aluminium furnace. Since the selenium contents of many alloys are of concern from health and environmental perspectives, their values should be provided. In this work, a laboratory reference material (LRM) based on electrolytic manganese was produced to assure our routine quality control method, where selenium is analysed by hydride generation followed by optical emission spectrometry with inductively coupled plasma (HG–ICP–OES). Therefore, the present paper describes in detail the preparation procedure for and the results from homogeneity and stability studies performed on electrolytic manganese LRM. For this purpose, a commercial electrolytic manganese lot was selected and the main factors involved in the preparation of the material (pretreatment step, homogenization, bottling and storage) were carefully studied and established in order to guarantee the long-term stability of the LRM. The results obtained showed that the LRM developed was a fit-for-purpose material for the quality control of the routine analysis of selenium.     

Formation of Bi-Sb, Bi-Sn, and Bi-Sb-Sn Nanoclusters in Silica Xerogel Matrices from Mixed-Metal Oxide Precursors

Homogeneous mixed-metal oxides of the general formula (Bi/E/Si)O _x , where E represents a dopant element (E=Sb, Sn, or Sb/Sn), can be prepared using typical sol-gel processing techniques. Reduction of the in-situ Bi(III) and E ions by hydrogen affords nanocomposites of Bi-Sb, Bi-Sn, or Bi-Sb-Sn widely dispersed throughout the silica xerogel matrix. The materials prepared have high Bi-E metal loading of 52–60 wt. % containing Bi-E alloy nanoclusters of 12–15 nm average diameter. These results demonstrate a convenient method for the production of practical quantities of nanostructured bismuth alloy ceramic composites at high metal content.     

Determination of dissolved manganese in natural waters by differential pulse cathodic stripping voltammetry

A procedure based on differential pulse cathodic stripping voltammetry on the graphite electrode is described for the determination of dissolved manganese in natural waters buffered at pH about 6.5 with acetate solution. In order to avoid interference of iron(II) the addition of fluoride is used. The limit of detection is 3 g/l for a deposition time of 6 min. Acidification and UV-irradiation are recommended for samples containing dissolved organic matter. Results of manganese determination in table mineral waters are reported and the possibility of manganese speciation is discussed.     

Synthesis, nuclear, and magnetic structures and magnetic properties of [Mn3(OH)2(SO4)2(H2O)2

[Mn(3)(OH)(2)(SO(4))(2)(H(2)O)(2)] and its deuterated analogue were synthesized by a hydrothermal technique and characterized by differential thermal analysis, thermogravimetric analysis, and IR spectroscopy. Its nuclear structure, determined by single-crystal X-ray analysis and Rietveld analysis of neutron powder-diffraction data, consists of a 3D network of chains of edge-sharing Mn(1)O(6), running along the c axis, connected by the apices of Mn(2)O(6) and SO(4) units. It is isostructural to the nickel analogue. Determination of the magnetic structure and measurements of magnetization and heat capacity indicate the coexistence of both magnetic long-range ordering (LRO) and short-range ordering (SRO) below a Néel temperature of 26 K, while the SRO is retained at higher temperatures. The moments of the two independent Mn atoms lie in the bc plane, and that of Mn(1) rotates continuously by 54 degrees towards the c axis on decreasing the temperature from 25 to 1.4 K. While the SRO may be associated with frustration of the moments within a Mn(3) trimer, the LRO is achieved by antiparallel alignment of the four symmetry-related trimers within the magnetic unit cell. A spin-flop field, measured by dc and ac magnetization on a SQUID, is observed at 15 kOe.     

高分子合金分离膜材料及结构研究进展

膜材料液相共混制备高分子合金分离膜不但可以调节膜材料与被分离物的亲和性，也在一定程度上改变了膜的结构。本文介绍高分子材料浓相共混对膜材料的亲水性、耐污染性及其它理化性能的影响和对膜结构的调节作用，同时指出高分子材料间的相容性是影响合金膜结构的重要因素。     

X-射线荧光光谱法测定钛铁中的硅、锰、磷、铝

介绍用X-射线荧光光谱仪测定钛铁中Si、Mn、P、Al含量的方法,通过试验确定了合适的研磨时间、压力和保压时间,用压片法制样,建立了各元素的工作曲线,各元素的测定范围分别为Si3.00%～6.00%,Mn1.00%～3.00%,P0.030%～0.070%,Al5.00%～9.00%。通过强度测量得到测定Si、Mn、P、Al的相对标准偏差分别为0.074%、0.308%、0.383%、0.040%,精密度满足测试要求。将该方法测定结果与化学法比对,准确度满足国家标准方法分析误差的要求。     

Characterization of non‐Cr‐based deoxidizers on Al alloy 7475‐T7651

The effects of three non‐chromate‐based deoxidizers, namely NaBrO₃/HNO₃, (NH₄)₄Ce(SO₄)₄/H₂SO₄ and Fe(III)/HF/HNO₃, on the Al alloy 7475‐T7651 were investigated. Several analytical methods were employed, including SEM, AES, transmission electron microscopy (TEM), electron energy‐loss spectroscopy (EELS) and glow discharge optical emission spectrometry (GDOES), to study the effects on the surface of this alloy after each treatment compared with the as‐received and alkaline‐cleaned alloy surfaces. The untreated alloy was found to have a thick oxide of 200–320 nm, consisting mainly of MgO. Alkaline cleaning results in an etching effect that thins the oxide and also deposits a thin silicate layer on the surface. In the case of the deoxidizers, there is significant removal of the native oxide of the alloy by the NaBrO₃/HNO₃ deoxidizer. There is also evidence of intermetallic attack on the alloy. The (NH₄)₄Ce(SO₄)₄/H₂SO₄ deoxidizer, which is a low‐etch‐rate deoxidizer, resulted in a slight thinning of the oxide. However, the effect was not significantly greater than with alkaline cleaning alone. The most effective deoxidizer in reducing the oxide thickness of the alloy is Fe(III)/HF/HNO₃, in which the etch rate was sufficiently high to remove completely the native oxide. In this case, equilibrium between oxide removal and the formation of new oxides on the alloy surface was achieved. Copyright © 2004 John Wiley & Sons, Ltd.