四（五氟化苯基）卟啉氯化铁选择催化氧化超临界丙烷的反应机理

 以BHT为自由基捕捉剂，研究了四（五氟化苯基）卟啉氯化铁（Ⅲ）将超临界丙烷高选择性催化氧化为丙醇的反应机理．通过GC－MS分析发现，反应产物中有PBHT，故可认为在超临界丙烷氧化反应过程中有丙基自由基存在，初步推断反应涉及自由基机理．同时发现高浓度BHT抑制反应，低浓度BHT促进反应的现象，而以戊烷为底物时没有促进作用．这是由于BHT的位阻效应所致．并对BHT存在时超临界丙烷氧化反应机理进行了初步的推断．     

A Novel Green Preparation of a, a''''-Bis (substituted benzylidene)-cycloalkanones Promoted by FeCl_3 6H-2O in Ionic Liquid

a, a'-Bis(substituted benzylidene)cycloalkanones were efficiently prepared from cycloalkanones and benzaldehydes in [bmim][BF4] by using iron(III) chloride hexahydrate as a catalyst. It is shown that [bmim][BF4] and iron(III) chloride hexahydrate can be quantitatively recovered and be reused effectively for many times. Compared with the known methods, this novel process has the advantage of being an envkonmentally benign process together with good yields and mild reaction conditions.     

Synthesis and structure of anhydrodimers of salicylaldehydes

Anhydrodimers have been synthesized by reactions of salicylaldehyde and 3,5-di-tert-butylsalicylaldehyde with SOCl₂ or PCl₅. A mechanism of condensation has been proposed, and the molecular structure of dibenzo-2,6,9-trioxabicyclo[3.3.1]nona-3,7-diene has been determined by X-ray structural analysis.Deceased.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 8, pp. 1549–1551, August, 1995.The work was supported by the Russian Foundation for Basic Research (Project No. 94-03-08653).     

三氯化钛存在下碘酸钾滴定法测定锡

提出了采用铝加铁混合还原剂还原,三氯化钛存在下碘酸钾滴定法测定锡的绝对测量方法,研究了三氯化钛抑制氧的作用效果及作用机理。应用于巴氏合金中锡含量的测定,方法简便、快速,结果准确可靠。     

钴（Ⅱ）与2,2’-联吡啶-1,1’-二氧化物的多核配合物的合成和性质

以无水CoCl2和2,2’-联吡啶-1,1’-二氧化物为原料,在DMF溶剂中合成了一种多核配合物.经元素分析、紫外光谱、红外光谱和摩尔电导等方法测得它的组成为[Co3(bipyO2)4Cl4]Cl2,并对该配合物的气敏特性进行了研究. 结果表明, 该配合物对氨气有良好的敏感性和选择性.由它制作的传感器可望用于涉氨化工生产中氨浓度的自动测量和控制.     

2，6－二氨基吡啶与苦基氯的反应历程研究

对２，６－二氨基吡啶与苦基氯的反应历程进行了研究。通过二氨基吡啶与几种多硝基卤代苯的反应、溶剂效应、ＮａＦ的促进作用和紫外光谱吸收，证实该反应属于芳香族亲核取代反应类型，按加成－消除历程进行，反应过渡态涉及一个Ｍｃｉｓｅｎｈｅｉｍｅｒ络合物。     

Fibers and 3D mesh scaffolds from biodegradable starch-based blends: production and characterization

The aim of this work is the production of fibers from biodegradable polymers to obtain 3D scaffolds for tissue engineering of hard tissues. The scaffolds required for this highly demanding application need to have, as well as the biological and mechanical characteristics, a high degree of porosity with suitable dimensions for cell seeding and proliferation. Furthermore, the open cell porosity should have adequate interconnectivity for a continuous flow of nutrients and outflow of cell metabolic residues as well as to allow cell growth into confluent layers. Blends of corn starch, a natural biodegradable polymer, with other synthetic polymers (poly(ethylene vinyl alcohol), poly(epsilon-caprolactone), poly(lactic acid)) were selected for this work because of their good balance of properties, namely biocompatibility, processability and mechanical properties. Melt spinning was used to produce fibers from all the blends and 3D meshes from one of the starch-poly(lactic acid) blends. The experimental characterization included the evaluation of the tensile mechanical properties and thermal properties of the fibers and the compression stiffness, porosity and degradation behavior of the 3D meshes. Light microscopy picture of 3D meshes.     

Comparison of the thermal behavior of three cellulose fibers mercerized or submitted to solar degradation

Comparison of Lyocell, modal and viscose fibers was performed by means of differential scanning calorimetry, thermogravimetry and scanning electron microscopy. Thermal analysis was performed in air atmosphere. Samples were mercerized (21.3 g 100 mL-1) or submitted to solar radiation (seven months). Solar degraded samples presents a higher thermal stability and are initially less degraded. Furthermore, Lyocell fiber is the most stable under thermal degradation conditions. Heating produces a reduction of the fiber diameter (about 50%). This revised version was published online in July 2006 with corrections to the Cover Date.     

Analysis of citrates and benzoates used in poly(vinyl chloride) by supercritical fluid extraction and gas chromatography

Supercritical fluid extraction (SFE) has been demonstrated to be a useful tool in the determination of additives in polymeric materials. This paper describes the determination of some citrates and benzoates in poly(vinyl chloride) blended with 33–34% of plasticizer using off-line SFE followed by gas chromatography. Experimental factors affecting SFE have been studied by gravimetric analysis, followed by analysis of the extracts using a gas chromatograph equipped with a flame ionization detector. The extraction process is governed by the solubility of the plasticizers in the supercritical fluid or by their diffusion through the polymer matrix, which depend on the pressure and temperature used. Maximum extraction (>99%) is obtained at pressures and temperatures higher than 40 MPa and 80 °C, respectively. Due to purge losses, the collection efficiency of plasticizers into a liquid solvent ranges from 85 to 90%. The applicability of the SFE method is demonstrated using real samples and comparing the results with those obtained by conventional Soxhlet extraction.     

氯化钠在球形纳米氧化铈形成过程中的作用

以水合碳酸铈为原料, 以氯化钠作为助磨剂和阻聚剂, 采用机械活化法制备了球形纳米氧化铈, 用XRD法研究了水合碳酸铈与氯化钠质量比、球磨时间、煅烧温度对CeO2粉体晶粒度的影响, 用TEM对最终产物粒子进行形貌观察. 结果表明: 在碳酸铈的球磨过程及其随后的煅烧过程中, 氯化钠的存在起到了很好的助磨和阻聚作用, 所得CeO2为类球形粒子, 分散性较好, 晶粒度约为30～50 nm.