Studies of photooxidative degradation of poly(vinyl chloride)/poly(ethylene oxide) blends

The photooxidative degradation of blends (in a full range of compositions) of amorphous poly(vinyl chloride) (PVC) with semicrystalline poly(ethylene oxide) (PEO) in the form of thin films is investigated using absorption spectroscopy (UV–visible and Fourier transform infrared) and atomic force microscopy (AFM). The amount of insoluble gel formed as a result of photocrosslinking is estimated gravimetrically. It is found that the PVC/PEO blendsí susceptibility to photooxidative degradation differs from that pure of the components and depends on the blend composition and morphology. Photoreactions such as degradation and oxidation are accelerated whereas dehydrochlorination is retarded in blends. The photocrosslinking efficiency in PVC/PEO blends is higher than in PVC; moreover, PEO is also involved in this process. AFM images showing the lamellar structure of semicrystalline PEO in the blend lead to the conclusion that the presence of PVC does not disturb the crystallization process of PEO. The changes induced by UV irradiation allow the observation of more of the distinct PEO crystallites. This is probably caused by recrystallization of short, more mobile chains in degraded PEO or by partial removal of the less stable amorphous phase from the film surface. These results confirm previous information on the miscibility of PVC with PEO. The mechanism of the interactions between the components and the blend photodegradation are discussed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 585–602, 2004     

Mutual influence of the morphology and capillary rheological properties in nylon/glass‐fiber/liquid‐crystalline‐polymer blends

Nylon‐6/glass‐fiber (GF)/liquid‐crystalline‐polymer (LCP) ternary blends with different viscosity ratios were prepared with three kinds of nylon‐6 with different viscosities as matrices. The rheological behaviors of these blends were characterized with capillary rheometry. The morphology was observed with scanning electron microscopy and polarizing optical microscopy. This study showed that although LCP did not fibrillate in binary nylon‐6/LCP blends, LCP fibrillated to a large aspect ratio in some ternary blends after GF was added. The addition of 5 wt % LCP significantly reduced the melt viscosity of nylon‐6/GF blends to such an extent that some nylon‐6/GF/LCP blends had quite low viscosities, not only lower than those of neat resins and nylon‐6/GF blends but also lower than those of corresponding nylon‐6/LCP blends. The mutual influence of the morphology and rheological properties was examined. The great reduction of the melt viscosity was considered the result of LCP fibrillation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1619–1627, 2004     

Influence of solvents on the formation of ultrathin uniform poly(vinyl pyrrolidone) nanofibers with electrospinning

Although there have been many reports on the preparation and applications of various polymer nanofibers with the electrospinning technique, the understanding of synthetic parameters in electrospinning remains limited. In this article, we investigate experimentally the influence of solvents on the morphology of the poly(vinyl pyrrolidone) (PVP) micro/nanofibers prepared by electrospinning PVP solution in different solvents, including ethanol, dichloromethane (MC) and N,N‐dimethylformamide (DMF). Using 4 wt % PVP solutions, the PVP fibers prepared from MC and DMF solvents had a shape like a bead‐on‐a‐string. In contrast, smooth PVP nanofibers were obtained with ethanol as a solvent although the size distribution of the fibers was somewhat broadened. In an effort to prepare PVP nanofibers with small diameters and narrow size distributions, we developed a strategy of using mixed solvents. The experimental results showed that when the ratio of DMF to ethanol was 50:50 (w/w), regular cylindrical PVP nanofibers with a diameter of 20 nm were successfully prepared. The formation of these thinnest nanofibers could be attributed to the combined effects of ethanol and DMF solvents that optimize the solution viscosity and charge density of the polymer jet. In addition, an interesting helical‐shaped fiber was obtained from 20 wt % PVP solution in a 50:50 (w/w) mixed ethanol/DMF solvent. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3721–3726, 2004     

Electrospinning of ultrafine cellulose acetate fibers: Studies of a new solvent system and deacetylation of ultrafine cellulose acetate fibers

Electrospinning of cellulose acetate (CA) in a new solvent system and the deacetylation of the resulting ultrafine CA fibers were investigated. Ultrafine CA fibers (∼2.3 μm) were successfully prepared via electrospinning of CA in a mixed solvent of acetone/water at water contents of 10–15 wt %, and more ultrafine CA fibers (0.46 μm) were produced under basic pH conditions. Ultrafine cellulose fibers were regenerated from the homogeneous deacetylation of ultrafine CA fibers in KOH/ethanol. It was very rapid and completed within 20 min. The crystal structure, thermal properties, and morphology of ultrafine CA fibers were changed according to the degree of deacetylation, finally to those of pure cellulose, but the nonwoven fibrous mat structure was maintained. The activation energy for the deacetylation of ultrafine CA fibers was 10.3 kcal/mol. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 5–11, 2004     

Annealing behavior of gel‐spun polyethylene fibers at temperatures lower than needed for significant shrinkage

The annealing at 373 K of ultrastrong, gel‐spun polyethylene (PE) has been studied. At this temperature, the fibers show no significant shrinkage. Still, a significant decrease in the mechanical properties is observed. The fibers have been analyzed with differential scanning calorimetry (DSC), temperature‐modulated differential scanning calorimetry (TMDSC), atomic force microscopy (AFM), and small‐angle X‐ray scattering (SAXS). During the annealing, the glass transition of the intermediate phase is exceeded, as shown by DSC. When split for structure analysis by AFM, the annealed fibers undergo plastic deformation around the base fibrils instead of brittle fracture. The quasi‐isothermal TMDSC experiments are compared to the minor structural changes seen with SAXS and AFM. The loss of performance of the PE fibers at 373 K is suggested to be caused by the oriented intermediate phase, and not by major changes in the structure or morphology. The overall metastable, semicrystalline structure is shown by TMDSC to posses local regions that can melt reversibly. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 403–417, 2003     

Effects of tributyltin(IV) chloride on the gametes and fertilization of Ascidia malaca (Ascidiacea: Tunicata)

Ascidia malaca gametes before fertilization incubated in 10^?5 or 10^?7 M solutions of tributyltin(IV) chloride, TBTCl, for 3 h appear highly damaged under transmission electron microscopy observation. Also, the fertilization process is affected by the compound: the damaged spermatozoa are present in the vitelline coat and the egg does not cleave. An increase of microbodies, structurally similar to peroxisomes, have been detected in the egg peripheral cytoplasm, probably in relation to their role in alleviating damage to some cellular components. The results have shown that the reproduction of ascidians under unfavourable environmental conditions is prevented. Copyright © 2003 John Wiley & Sons, Ltd.     

A bio-mechanical model for coupling cell contractility with focal adhesion formation

Focal adhesions (FAs) are large, multi-protein complexes that provide a mechanical link between the cytoskeletal contractile machinery and the extracellular matrix. They exhibit mechanosensitive properties; they self-assemble upon application of pulling forces and dissociate when these forces are decreased. We rationalize this mechano-sensitivity from thermodynamic considerations and develop a continuum framework in which the cytoskeletal contractile forces generated by stress fibers drive the assembly of the FA multi-protein complexes. The FA model has three essential features: (i) the low and high affinity integrins co-exist in thermodynamic equilibrium, (ii) the low affinity integrins within the plasma membrane are mobile, and (iii) the contractile forces generated by the stress fibers are in mechanical equilibrium and change the free energies of the integrins. A general two-dimensional framework is presented and the essential features of the model illustrated using one-dimensional examples. Consistent with observations, the coupled stress fiber and FA model predict that (a) the FAs concentrate around the periphery of the cell; (b) the fraction of the cell covered by FAs increases with decreasing cell size while the total FA intensity increases with increasing cell size; and (c) the FA intensity decreases substantially when cell contractility is curtailed.     

Local chain‐configuration dependence of the mechanisms of the chemical reaction of poly(vinyl chloride). IX. Novel results on stereoselectivity of chlorination reaction

A poly(vinyl chloride) (PVC) sample was chlorinated in solution in the presence of 2,2′‐azobisisobutyronitrile and by the fluid‐bed method. The aim was to evaluate the scope of the stereoselectivity of the chlorination reaction. The quantitative microstructural analysis of the residual PVC with a degree of chlorination was followed by ¹³C NMR spectroscopy. From the evolution of the content of isotactic (mm), heterotactic (mr), and syndiotactic (rr) triads and of mmmm, mmmr, and rmmr isotactic pentads in the unchlorinated parts of the polymer, it was unambiguously inferred that the chlorination reaction proceeds by a stereoselective mechanism in that the mr heterotactic triads are the most reactive structures followed by the isotactic triad at mmmr and rmmr pentads. This conclusion was confirmed on the basis of the Fourier transform infrared results. The results provide valuable information regarding the effect of tacticity and related local conformations in the chemical reactions of PVC. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 508–519, 2003     

Cellulose-based fibers from liquid–crystalline solutions. II. Processing and morphology of acetate/butyrate esters

Fibers were spun from isotropic and anisotropic dimethylacetamide solutions of cellulose esters. Take-up speeds of the dry jet/wet spinning process varied. Water served as the coagulant. The mechanical properties of the fibers increased as spinning progressed from the isotropic to the anisotropic state of the solution. A trade-off in solubility and fiber properties was noted as the butyryl acetyl ratio decreased. Whereas high butyryl content enhances both overall solubility and the formation of liquid–crystalline solutions at lower concentration, it results in lower fiber modulus and strength. Morphology of the fibers depended on the coagulation rate which was influenced by the concentration of the sppinning solution. The level of orientation and crystallinity of the fibers increased somewhat when they were spun from liquid-crystalline solutions. © 1993 John Wiley & Sons, Inc.     

The preparation and structure of 1,4,5,6,7,7-hexachloro-2-endo-ferrocenylhydroxymethyl-3-endo-hydroxymethyl-5-norbornene

The crystal structure of a novel ferrocene derivative with potential flame-retardant/smoke-suppressant activity, 1,4,5,6,7,7-hexachloro-2-endo-ferrocenyl-hydroxymethyl-3-endo-hydroxymethyl-5-norbornene, has been determined. Some of the carbon–carbon bonds within the chlorendic residue are unusually long, and there is no interaction between the hydroxyl groups and the iron atom. There is evidence of intramolecular hydrogen bonding between the two hydroxyl groups.