卡尔曼滤波析相光度法同时测定锰铁铜锌镉的研究——5-Br-PADAP—Triton X-100体系

运用卡尔曼滤波递推法,以2-(5-溴-2-吡啶偶氮)—5-二乙氨基苯酚(5-Br-PADAP)为显色剂,建立了同时测定锰、铁、铜、锌、镉析相光度法.在pH9.0硼酸-氢氧化钠介质中,胶束溶液在95℃加热1h,配合物被Triton X-100相完全富集,最大吸收峰分别为锰566nm、铁556nm、铜560nm、锌562nm、镉557nm,工作曲线范围除镉为0～8μg/5ml外,其余均为0～10μg/5ml.应用于大米中锰铁铜锌镉的同时测定,结果满意.     

往复挤压准晶增强快速凝固Mg92.5Zn6.4Y1.1合金

采用往复挤压工艺将快速凝固Mg92.5Zn6.4Y1.1合金薄带在330℃挤压2道次和4道次,然后正挤压制成Φ10 mm的棒材。用OM,TEM,XRD及DTA研究了往复挤压过程中准晶相I-Mg3YZn6弥散析出及对力学性能的影响。研究表明,往复挤压有利于快速凝固Mg92.5Zn6.4Y1.1合金薄带的焊合,获得组织致密、均匀、高强韧合金。往复挤压2道次,相组成为-αMg和准晶I-Mg3YZn6,脱溶析出纳米准晶相较少;4道次相组成为-αMg和准晶I-Mg3YZn6及MgZn相,脱溶弥散析出的纳米I-Mg3YZn6准晶相及MgZn相较多。往复挤压提高材料的拉伸性能,其主要原因是细晶强化和析出强化。     

热解-还原法制备单分散Fe3O4亚微空心球

在用模板法水解FeCl3制备单分散聚(苯乙烯-共-丙烯酸)/Fe2O3[P(St-co-AA)/Fe2O3]核壳粒子的基础上, 于N2环境下热解内核直接得到了单分散的磁性Fe3O4亚微空心球. 用透射电镜(TEM)、场发射扫描电镜(FESEM)、X射线衍射(XRD)、振动样品磁强计(VSM)表征并测试了空心微球的结构形貌、成分以及静磁性能. 结果表明, P(St-co-AA)/Fe2O3核壳粒子在热处理过程中, 由于内核热解生成的有机小分子将Fe2O3 壳层同时还原为Fe3O4, 从而生成了粒径和壁厚均匀的单分散Fe3O4亚微空心球. 该空心微球在室温下的饱和磁化强度、剩余磁化强度和矫顽力分别为50.91 A·m2·kg-1、3.97 A·m2·kg-1和2.33 kA·m-1.     

Solid-phase extraction of iron(III) with an ion-imprinted functionalized silica gel sorbent prepared by a surface imprinting technique

A new Fe(III)-imprinted amino-functionalized silica gel sorbent was prepared by a surface imprinting technique for selective solid-phase extraction (SPE) of Fe(III) prior to its determination by inductively coupled plasma atomic emission spectrometry (ICP-AES). Compared with non-imprinted polymer particles, the ion-imprinted polymers (IIPs) had higher selectivity and adsorption capacity for Fe(III). The maximum static adsorption capacity of the ion-imprinted and non-imprinted sorbent for Fe(III) was 25.21 and 5.10 mg g⁻¹, respectively. The largest selectivity coefficient of the Fe(III)-imprinted sorbent for Fe(III) in the presence of Cr(III) was over 450. The relatively selective factor (α_r) values of Fe(III)/Cr(III) were 49.9 and 42.4, which were greater than 1. The distribution ratio (D) values of Fe(III)-imprinted polymers for Fe(III) were greatly larger than that for Cr(III). The detection limit (3σ) was 0.34 μg L⁻¹. The relative standard deviation of the method was 1.50% for eight replicate determinations. The method was validated by analyzing two certified reference materials (GBW 08301 and GBW 08303), the results obtained is in good agreement with standard values. The developed method was also successfully applied to the determination of trace iron in plants and water samples with satisfactory results.     

Methane Combustion Over Fe, Co and Ni Modified Manganese Oxide Catalysts

Fe-Mn, Co-Mn and Ni-Mn composite oxide catalysts based on high specific surface area MnO₂ precursor were prepared and applied to catalytic combustion of CH₄. Results were compared with that of unmodified MnOx and 1wt.% Pd/-Al₂O₃. Below 450°C, manganese oxide catalysts show higher activity than Pd/-Al₂O₃, while the modified manganese oxide catalysts exhibit higher activity than the unmodified one below 420°C. All catalysts were characterized by means of N₂-BET, XRD, TG-DTA and H₂-TPR. Due to the interaction between Fe, Co or Ni oxides and manganese oxide, the activity of the oxygen species of the modified catalysts is improved, which leads to the increase of their CH₄ combustion activity.     

低钴AB5型稀土系贮氢电极合金的研究

为了进一步降低AB5型混合稀土系贮氢合金的成本,采用Cr,Si,Cu替代Co和调节化学计量比的方法制备低钴AB5型贮氢合金。结果表明:3种取代元素在寿命方面的效果依次为Si>Cr>Cu,在放电容量和活化性能方面依次是Cu>Cr>Si。Cr,Cu,Si只有少量的替代才可能发挥其有利影响;通过非化学计量比的调节,低钴混合稀土系贮氢电极合金的放电容量、活化性能及倍率放电能力都能较好地达到实用要求,但是循环寿命有待提高。     

Preparation and Characterization of Nanotitanium Dioxide Coating Film Doped with Fe^3＋ Ions on Porous Ceramic

The nanotitanium dioxide （TiO2） photocatalytic and porous ceramic filtering technique is one of the advanced methods to effectively treat organic wastewater. The TiO2 sol doped with Fe^3＋ ions was prepared by sol-gel processing. The influences of the process conditions of coating nanophotocatalytic material- Fe^3＋-TiO2 film on the surface of porous ceramic filter by dipping-lift method on the performance of porous ceramic filter were studied. The porous ceramic filters have two functions at the same time, filtration and photocatalytic degradation. The results of this study showed that the pH and viscosity of the sol, amount of Fe^3＋ ions doped as well as the coating times greatly affect the quality of coating film, the performance parameters and the photocatalytic activity of the porous ceramic filter. When the pH of the sol is 3-4, the viscosity is about 6 mPa.S, the amount of doped Fe^3＋ ions is about 2.0 g/L, the porous ceramic filter has been shown to have the best filtering performance and photocatalytic activity. In this condition, the porosity of porous ceramic is about 42.5%, the pore diameter is 8-10μm. The degradation of methyl-orange is 74.76% under lighting for 120 rain.     

铜(Ⅱ)-铬天青S-过氧化氢体系催化光度法测定痕量铜

本文研究了在氨水介质中,痕量铜对过氧化氢氧化铬天青S褪色反应的催化作用,建立了一个催化光度法测定痕量铜的新方法。线性范围为0～20ng/mL,检出限为5.59×10~(-11)g/mL,并用于铝合金标准样品,环境标准样品和自来水中痕量铜的测定。     

FT合成沉淀Fe／Cu／K催化剂有效因子的计算Ⅰ．工业颗粒催化剂有效因子的计算

用包括水抑制作用的动力学方程，根据建立的反应扩散模型和ＦＴ合成化学计量关系，计算了工业原颗粒ＦＴ合成沉淀Ｆｅ／Ｃｕ／Ｋ催化剂在工业操作条件下的有效因子。根据不同的产物组成，建立了三种化学计量关系式，比较了气相反应和气液反应的有效因子，确立了ＦＴ合成沉淀Ｆｅ／Ｃｕ／Ｋ催化剂有效因子的计算方法。在ＦＴ合成反应条件下，产物蜡充满了催化剂的微孔，各组分在蜡中的扩散系数要比纯气相中的扩散系数小得多。在工况操作条件下（５２３Ｋ，２．５ＭＰａ，５００ｈ￣（－１），尾气循环比３．０），工业原颗粒（ｄ＿ｐ＝２．５ｍｍ，ｌ＿ｐ＝５～１０ｍｍ）催化剂的实际有效因子是纯气相反应的一半左右，计算的平均有效因子分别为０．４０和０．４２。