C(2×2)S/Fe(001)吸附体系的SCF-Xa-MS研究

采用SCF-X_α-MS方法, 对于C(2×2)S/Fe(001)吸附体系, 选择Fe_5S和Fe_9S两种原子簇模型, 研究了该吸附体系的电子结构、吸附成键特征及其相互作用图象。结果表明, S吸附于Fe(001)单晶表面具有较强的定域性质, S原子与底物Fe原子之间的吸附相互作用主要表现为S(3p)-Fe(4s,3d)之间的轨道相互作用。通过对表面吸附键长的优化, 其结果与X.S.Zhang等的ARPEFS的实验结果一致。     

Pt/Al2O3蜂窝状催化剂上NO选择性催化还原反应动力学研究

采用多次涂层和浸渍法制备了蜂窝状Pt/Al2O3催化剂，并在高空速和大气体流量条件下对无梯度循环式反应器和积分反应器上催化剂的活性进行了比较。同时采用循环式反应器对动力学数据进行了测定。根据Langmuir-Hinshelwood模型和实验结果，推测了NO-C3H6-O2体系的SCR反应机理，并导出了NO和C3H6反应速率的数学表达式。据此所计算的理论模拟值能够与实验值很好地吻合。实验结果表明，氧气浓度对NO和C3H6的反应速率有明显的影响，二者均随着氧浓度c (O2)的增加达到峰值，再增加氧气浓度时，C3H6的反应速率r(C3H6)保持不变，而NO反应速率r (NO)却下降，而且下降的程度随着温度的升高而加剧。同时，随着氧气浓度增加，r (NO)达到最大值时的温度亦随之下降。     

助剂Cu对Ni/γ-Al2O3催化剂低温还原性能影响

制备了一系列铜质量分数不同的CuNi/γ-Al2O3催化剂，进行了TPR和XRD表征并测定了该系列催化剂对苯加氢制环己烷的催化活性。结果表明，助剂Cu的负载量对低温（160 ℃）还原后催化剂的催化活性影响很大，在铜镍原子摩尔比为1∶1时，催化剂具有较高的催化活性和稳定性；添加铜组分可促进镍在载体表面分散，使负载NiO的还原温度降低，催化活性提高。     

湿热证动物模型微量元素、维生素E变化及清香散的调节作用

采用多因素造模方法复制成湿热证动物模型，观察了动物模型微量元素Zn、Cu、Fe、Se和维生素E代谢水平的变化。结果显示，模型动物血清Zn下降（P＜0．05），Cu升高（P＜0．05或P＜0．01），Fe变化不大（P＞0．05），血Se水平下降（P＜0．05），血浆维生素E含量减少（P＜0．01）。经清热祛湿的经验方清香散治疗后，治疗I组动物血清Zn、血Se、血浆维生素E明显升高（P＜0．05），血清Cu下降（P＜0．05）；治疗Ⅱ组血浆血清Cu有变化（P＜0．05）外，其余变化不大。     

微波辅助快速制备2D/1D ZnIn2S4/TiO2 S型异质结及其光催化制氢性能

The threat and global concern of energy crises have significantly increased over the last two decades. Because solar light and water are abundant on earth, photocatalytic hydrogen evolution through water splitting has been considered as a promising route to produce green energy. Therefore, semiconductor photocatalysts play a key role in transforming sunlight and water to hydrogen energy. To date, various photocatalysts have been studied. Among them, TiO₂ has been extensively investigated because of its non-toxicity, high chemical stability, controllable morphology, and high photocatalytic activity. In particular, 1D TiO₂ nanofibers (NFs) have attracted increasing attention as effective photocatalysts because of their unique 1D electron transfer pathway, high adsorption capacity, and high photoinduced electron–hole pair transfer capability. However, TiO₂ NFs are considered as an inefficient photocatalyst for the hydrogen evolution reaction (HER) because of their disadvantages such as a large band gap (~3.2 eV) and fast recombination of photoinduced electron–hole pairs. Therefore, the development of a high-performance TiO₂ NF photocatalyst is required for efficient solar light conversion. In recent years, several strategies have been explored to improve the photocatalytic activity of TiO₂ NFs, including coupling with narrow-bandgap semiconductors (such as ZnIn₂S₄). Recently, microwave (MW)-assisted synthesis has been considered as an important strategy for the preparation of photocatalyst semiconductors because of its low cost, environment-friendliness, simplicity, and high reaction rate. Herein, to overcome the above-mentioned limiting properties of TiO₂ NFs, we report a 2D/1D ZnIn₂S₄/TiO₂ S-scheme heterojunction synthesized through a microwave (MW)-assisted process. Herein, the 2D/1D ZnIn₂S₄/TiO₂ S-scheme heterojunction was constructed rapidly by using in situ 2D ZnIn₂S₄nanosheets decorated on 1D TiO₂ NFs. The loading of ZnIn₂S₄ nanoplates on the TiO₂ NFs could be easily controlled by adjusting the molar ratios of ZnIn₂S₄ precursors to TiO₂ NFs. The photocatalytic activity of the as-prepared samples for water splitting under simulated solar light irradiation was assessed. The experimental results showed that the photocatalytic performance of the ZnIn₂S₄/TiO₂ composites was significantly improved, and the obtained ZnIn₂S₄/TiO₂ composites showed increased optical absorption. Under optimal conditions, the highest HER rate of the ZT-0.5 (molar ratio of ZnIn₂S₄/TiO₂= 0.5) sample was 8774 μmol·g^-1·h^-1, which is considerably higher than those of pure TiO₂ NFs (3312 μmol·g^-1·h^-1) and ZnIn₂S₄nanoplates (3114 μmol·g^-1·h^-1) by factors of 2.7 and 2.8, respectively. Based on the experimental data and Mott-Schottky analysis, a possible mechanism for the formation of the S-scheme heterojunction between ZnIn₂S₄ and TiO₂ was proposed to interpret the enhanced HER activity of the ZnIn₂S₄/TiO₂heterojunctionphotocatalysts.      

ELECTROSPRAYING/ELECTROSPINNING OF POLY(γ-STEARYL-L-GLUTAMATE): FORMATION OF SURFACES WITH SUPERHYDROPHOBICITY

  Electrospraying/electrospinning of poly(γ-stearyl-L-glutamate) (PSLG) was investigated on a series solutions with different concentrations in chloroform. Field emission scanning electron microscopy (FESEM) and attenuated total reflectance Fourier transform infrared spectroscopy (FT-IR/ATR) were used to characterize the morphology and structure of the electrosprayed/electrospun polypeptide mats. It was found that electrospraying of PSLG with concentrations lower than 16 wt% afforded beads, while microfibers could be electrospun at the concentration of 22 wt%. The hydrophobicity of the electrosprayed/electrospun PSLG mats was investigated with static water contact angle (WCA) and tilt angle measurements. It was demonstrated that the superhydrophobic surfaces of PSLG with WCAs and tilt angles in the ranges of 150°-170° and 16.5°-4.2°, respectively, were obtained through electrospraying/electrospinning process.     

N-TiO2/ZnO复合纳米管阵列的掺杂机理及其光催化活性

以ZnO纳米柱阵列为模板, 采用溶胶-凝胶法制备出TiO2/ZnO和N掺杂TiO2/ZnO的复合纳米管阵列. 扫描电镜(SEM)、X射线光电子能谱(XPS)和紫外-可见漫反射吸收光谱(UV-Vis)的结果表明: 两种阵列的纳米管均为六角形结构, 直径约为100 nm, 壁厚约为20 nm; 在N-TiO2/ZnO复合纳米管阵列中, 掺入的N离子主要是以N-Ox、N-C和N-N的形式化学吸附在纳米管表面, 仅有少量的N离子以取代式掺杂的方式占据TiO2晶格O的位置; 表面N物种形成的表面态能级和取代式掺杂导致带隙的窄化, 增强了纳米管阵列的光吸收效率, 促进了光生载流子的分离. 光催化实验结果表明, N离子的掺杂有利于N-TiO2/ZnO复合纳米管阵列光催化活性的提高.     

废水中偏二甲肼在Ni/Fe催化剂上的催化分解研究

研究了Ni/Fe催化剂对废水中偏二甲肼臭氧化分解的催化作用,考察了组分含量、体系的pH值和偏二甲肼初始浓度对催化反应的影响.结果表明,Ni/Fe催化剂对水中偏二甲肼的臭氧化具有良好的催化活性.催化剂组分含量、体系的pH值和初始浓度对反应的影响程度不大.对催化剂的XRD表征结果表明,催化剂主要由尖晶石结构的铁酸盐和FeNi3合金相组成,催化剂的良好催化性能与催化剂中尖晶石结构的铁酸盐和FeNi3合金相的形成有关.     

探究Cu/ZnO相互作用对CO2加氢制甲醇反应性能的影响

Using renewable green hydrogen and carbon dioxide (CO₂) to produce methanol is one of the fundamental ways to reduce CO₂ emissions in the future, and research and development related to catalysts for efficient and stable methanol synthesis is one of the key factors in determining the entire synthesis process. Metal nanoparticles stabilized on a support are frequently employed to catalyze the methanol synthesis reaction. Metal-support interactions (MSIs) in these supported catalysts can play a significant role in catalysis. Tuning the MSI is an effective strategy to modulate the activity, selectivity, and stability of heterogeneous catalysts. Numerous studies have been conducted on this topic; however, a systematic understanding of the role of various strengths of MSI is lacking. Herein, three Cu/ZnO-SiO₂ catalysts with different strengths of MSI, namely, normal precipitation Cu/ZnO-SiO₂ (Nor-CZS), co-precipitation Cu/ZnO-SiO₂ (Co-CZS), and reverse precipitation Cu/ZnO-SiO₂ (Re-CZS), were successfully prepared to determine the role of such interactions in the hydrogenation of CO₂ to methanol. The results of temperature-programmed reduction (H₂-TPR) and X-ray photoelectron spectroscopy (XPS) characterization illustrated that the MSI of the catalysts was considerably affected by the precipitation sequence. Fourier transform infrared reflection spectroscopy (FT-IR) results indicated that the Cu species existed as CuO in all cases and that copper phyllosilicate was absent (except for strong Cu-SiO₂ interaction). Transmission electron microscopy (TEM), X-ray diffraction (XRD), and N₂O chemical titration results revealed that strong interactions between the Cu and Zn species would promote the dispersion of Cu species, thereby leading to a higher CO₂ conversion rate and improved catalytic stability. As expected, the Re-CZS catalyst exhibited the highest activity with 12.4% CO₂ conversion, followed by the Co-CZS catalyst (12.1%), and the Nor-CZS catalyst (9.8%). After the same reaction time, the normalized CO₂ conversion of the three catalysts decreased in the following order: Re-CZS (75%) > Co-CZS (70%) > Nor-CZS (65%). Notably, the methanol selectivity of the Re-CZS catalyst was found to level off after a prolonged period, in contrast to that of Co-CZS and Nor-CZS. Investigation of the structural evolution of the catalyst with time on stream revealed that the high methanol selectivity of the catalyst was caused by the reconstruction of the catalyst, which was induced by the strong MSI between the Cu and Zn species, and the migration of ZnO onto Cu species, which caused an enlargement of the Cu/ZnO interface. This work offers an alternative strategy for the rational and optimized design of efficient catalysts.     

无机胶体法制备Pt/C催化剂及其性能表征

采用无机胶体法制备用于质子交换膜燃料电池(PEMFC)的Pt/C催化剂。研究了影响PtO₂胶体生成和稳定性的因素(溶液的pH值、浓度和温度条件等)以及不同还原剂浓度对Pt/C催化剂性能的影响。透射电子显微镜测试结果表明，采用经优化的工艺条件所制备的Pt/C催化剂平均粒径为3 nm，且分散性好、粒度均匀。X-射线衍射分析表明，催化剂中Pt(111)晶面的相对含量较高，有利于加速氧还原反应。单体PEMFC的电压/电流密度曲线测试表明，所制备的Pt/C催化剂具有良好的电化学性能。