General expression of the calibration curve for the CR-39 radon track detectors

The CR-39 detectors are widely used as passive radon dosimeters, as well as in physics laboratories or for industrial applications. For what concerns radon monitoring, the calibration curve which is usually adopted corresponds to a linear relation between the actual etched track density and the track density counted by an automatic acquisition system. This linear calibration provides very accurate radon exposure assessments in a restricted range of etched track density, however it neglects the effect of the tracks overlapping that becomes as relevant as the track density increases. In the present work the mathematical expression of the area covered by a set of uniformly distributed tracks is deduced. This result allows then to infer the probability that the system acquires the right track density, providing a general calibration curve for a solid state radon track detector. The process of track production and reading routine is also simulated adopting a Monte Carlo approach, showing that the obtained results are in agreement with the function proposed as calibration curve. Moreover, a linear dependence between the track average area and the rate parameter of the calibration curve has been observed. Finally a semi-empirical correlation based on the previous results is proposed.     

基于LabVIEW和Arduino的远程监控系统设计与实现

针对现场采集数据实时远程监控的要求,根据LabVIEW强大的功能模块和Arduino灵活易用的开发特点,提出以Arduino为控制器,采用Arduino软件与LabVIEW软件交互编程的设计思想。为解决LabVIEW在本地服务器Web发布的局限性,同时简化系统的硬件设计,增加使用的灵活性,使用云计算作为服务器,设计实现了一种基于LabVIEW和Arduino的无线串口采控和实时同步Web发布的系统。测试结果表明,该系统界面友好,运行可靠,可扩展性很强,可以在整个互联网上通过网页建立Web请求。     

石化厂区有毒气体泄漏在线监测平台的构建

针对石化厂区在生产过程中可能发生有毒气体泄露带来的生产安全问题,构建了石化厂区有毒气体在线监测平台。该平台是由PC监控中心、网络监控中心、ARM便携式终端、安卓手机客户端组成。实现对石化厂区中有毒气体及环境参数的实时、在线监测和预警,使生产管理人员掌握石化厂区的有毒气体实时动态信息,对可能引发危险事故的因素及时排除,把危险控制在始发阶段,以实现化工生产的安全、持续、高效进行。测试结果表明该平台能实现所设计的各项功能,并具有良好的稳定性、安全性和实用性。     

基于扩展DALI总线的智能照明系统设计

针对大型商业照明场合存在的如组网不便、照明效果单一,能源利用率底的问题,设计了一套基于扩展DALI总线的商业智能照明系统,以实现系统的大面积组网和集中控制,获得丰富的照明效果,实现系统的绿色环保运行。测试系统搭建完成后,实现了管理人员对系统的集中管理和远程监控;系统可按照工作日程表、时间表自动运行;具有分区、分组、单灯、场景等多种控制方式,控制灵活,能达到较好的照明效果和节能要求,可满足多种商业照明需求。     

Optimized precursor ion selection for labile ions in a linear ion trap mass spectrometer and its impact on quantification using selected reaction monitoring

The fragmentation of fragile ions during the application of an isolation waveform for precursor ion selection and the resulting loss of isolated ion intensity is well‐known in ion trap mass spectrometry (ITMS). To obtain adequate ion intensity in the selected reaction monitoring (SRM) of fragile precursor ions, a wider ion isolation width is required. However, the increased isolation width significantly diminishes the selectivity of the channels chosen for SRM, which is a serious problem for samples with complex matrices. The sensitive and selective quantification of many lipid molecules, including ceramides from real biological samples, using a linear ion trap mass spectrometer is also hindered by the same problem because of the ease of water loss from protonated ceramide ions. In this study, a method for the reliable quantification of ceramides using SRM with near unity precursor ion isolation has been developed for ITMS by utilizing alternative precursor ions generated by in‐source dissociation. The selected precursor ions allow the isolation of ions with unit mass width and the selective analysis of ceramides using SRM with negligible loss of sensitivity. The quantification of C18:0‐, C24:0‐ and C24:1‐ceramides using the present method shows excellent linearity over the concentration ranges from 6 to 100, 25 to 1000 and 25 to 1000 nM, respectively. The limits of detection of C18:0‐, C24:0‐ and C24:1‐ceramides were 0.25, 0.25 and 5 fmol, respectively. The developed method was successfully applied to quantify ceramides in fetal bovine serum. Copyright © 2014 John Wiley & Sons, Ltd.     

On‐Line Monitoring of Chemical Reactions by using Bench‐Top Nuclear Magnetic Resonance Spectroscopy

Real‐time nuclear magnetic resonance (NMR) spectroscopy measurements carried out with a bench‐top system installed next to the reactor inside the fume hood of the chemistry laboratory are presented. To test the system for on‐line monitoring, a transfer hydrogenation reaction was studied by continuously pumping the reaction mixture from the reactor to the magnet and back in a closed loop. In addition to improving the time resolution provided by standard sampling methods, the use of such a flow setup eliminates the need for sample preparation. Owing to the progress in terms of field homogeneity and sensitivity now available with compact NMR spectrometers, small molecules dissolved at concentrations on the order of 1 mmol L^?1 can be characterized in single‐scan measurements with 1 Hz resolution. Owing to the reduced field strength of compact low‐field systems compared to that of conventional high‐field magnets, the overlap in the spectrum of different NMR signals is a typical situation. The data processing required to obtain concentrations in the presence of signal overlap are discussed in detail, methods such as plain integration and line‐fitting approaches are compared, and the accuracy of each method is determined. The kinetic rates measured for different catalytic concentrations show good agreement with those obtained with gas chromatography as a reference analytical method. Finally, as the measurements are performed under continuous flow conditions, the experimental setup and the flow parameters are optimized to maximize time resolution and signal‐to‐noise ratio.     

金属标记结合高效液相色谱-选择离子监测质谱的蛋白质绝对定量新方法

建立了金属标记结合高效液相色谱-选择性离子监测质谱(SIM)的蛋白质绝对定量新方法。实验考察了金属标记效率、金属标记的稳定性、标记后肽段的色谱保留和质谱行为、新定量方法的线性范围和准确度。实验结果表明金属标记具有标记效率高,稳定性好,色谱保留行为一致等优点。另外,金属标记-选择离子监测质谱绝对定量方法灵敏度高,其定量限低至1 fmol,线性范围为1~500 fmol,线性范围内R2值大于0.99,具有良好的线性关系;经过测量,标准肽段的回收率为117.01%,说明该方法具有较高的准确度。将该方法应用于腾冲嗜热菌中烯醇酶蛋白的定量分析,相对标准偏差为5.47%,表明该方法的精密度高。以上结果表明该方法可以用于生物样本中的蛋白质的绝对定量分析,为比较简单的生物样本中蛋白质的绝对定量方法提供了一种新的选择。     

Real-time in situ monitoring of manufacturing process and CFRP quality by relative resistance change measurement

In situ monitoring of resin flow, impregnation of carbon fiber fabrics, and curing during composite manufacturing are very important for determining the quality of composite parts. In conventional methods, sensors, such as optical fibers and strain gages, are bonded to or embedded in the composites for measuring the changes in mechanical and chemical properties. Although they can detect resin curing behavior and impregnation of carbon fibers, they may adversely affect the manufacturing process or structural integrity of the composites. In this study, carbon fiber itself was used as a sensor that minimizes the degradation of mechanical properties and increases the efficiency of monitoring the manufacturing process. The change in the electrical resistance of carbon fiber fabrics was monitored during the various manufacturing processes when the resin flowed through the carbon fiber fabric and curing progressed. The effectiveness of this monitoring method was confirmed, and it is expected to be applicable in monitoring the quality of the finished composite parts.     

Live Monitoring of Strain-Promoted Azide Alkyne Cycloadditions in Complex Reaction Environments by Inline ATR-IR Spectroscopy

The strain-promoted azide alkyne cycloaddition (SPAAC) is a powerful tool for forming covalent bonds between molecules even under physiological conditions, and therefore found broad application in fields ranging from biological chemistry and biomedical research to materials sciences. For many applications, knowledge about reaction kinetics of these ligations is of utmost importance. Kinetics are commonly assessed and studied by NMR measurements. However, these experiments are limited in terms of temperature and restricted to deuterated solvents. By using an inline ATR-IR probe we show that the cycloaddition of azides and alkynes can be monitored in aqueous and even complex biological fluids enabling the investigation of reaction kinetics in various solvents and even human blood plasma under controlled conditions in low reaction volumes.     

High performance ethylene sensor based on palladium-loaded tin oxide: Application in fruit quality detection

Ethylene (C₂H₄), as a plant hormone, its emission can be served as an indicator to measure fruit quality. Due to the limited physiochemical reactivity of C₂H₄, it is a challenge to develop high performance C₂H₄ sensors for fruit detection. Herein, this paper presents a resistive-type C₂H₄ sensor based on Pd-loaded tin oxide (SnO₂). The C₂H₄ sensing performance of proposed sensor are tested at optimum operating temperature (250 °C) with ambient relative humidity (51.9% RH). The results show that the response of Pd-loaded SnO₂ sensor (11.1, R_a/R_g) is about 3 times higher than that of pristine SnO₂ (3.5) for 100 ppm C₂H₄. The response time is also significantly shortened from 7 s to 1 s compared with pristine SnO₂. Especially, the Pd-loaded SnO₂ sensor possesses good sensitivity (0.58 ppm⁻¹) at low concentration (0.05–1 ppm) with excellent linearity (R² = 0.9963) and low detection limit (50 ppb). The high sensing performance of Pd-loaded SnO₂ are attributed to the excellent adsorption and catalysis effects of Pd nanoparticle. Meaningfully, the potential applications of C₂H₄ sensor are performed for monitoring the maturity and freshness of fruits, which presents a promising prospect in fruit quality evaluation.