高密度聚乙烯/全同立构聚丙烯共混物超拉伸纤维的热行为与力学行为

用热拉法制备了高密度聚乙烯(HDPE)/全同立构聚丙烯(iPP)共混物超拉伸纤维,研究了拉伸比对其热行为及力学行为的影响,随拉伸比增加,纤维中HDPE与iPP的结晶度增大,熔融温度升高、熔程变宽;纤维中HDPE与iPP的结晶度低于其纯组分,熔融湿度与熔程基本不受组分比的影响,随拉伸比增加,纤维的模量增高,以HDPE为主的纤维的拉伸强度增大,以iPP为主的纤维拉伸强度增至一定值后,不再随拉伸比增加而增大,并有下降趋势。     

Combined effect of chemically compound graphene oxide‐calcium pimelate on crystallization behavior,morphology and mechanical properties of isotactic polypropylene

The combined nucleation effect of graphene oxide (GO) and calcium pimelate (CaPi) which are chemically compound together (expressed in GO ? CaPi) in isotactic polypropylene (iPP) was investigated. Fourier transform infrared (FTIR), X‐ray diffraction (XRD) and thermogravimetric analysis (TGA) verified that CaPi was chemically compound with GO by chelate bonds. The crystallization behavior and crystalline morphologies of iPP nucleated with different mass ratio of GO and CaPi were investigated. The crystallization peak temperature of iPP nucleated with 0.2 wt% GO ? CaPi with the mass ratio of 1:5 (GO1 ? C5) was increased by 8.3°C when compared with that of pure iPP, and the relative content of β‐crystal reached up to 0.7962. Whereas, the crystallization peak temperature of iPP nucleated with 0.2 wt% GO and CaPi which are blended together by mechanical force (expressed in GO + CaPi) with the mass ratio of 1:5 (GO1 + C5) was only increased by 5.0°C. It was attributed to that the aggregation of GO + CaPi caused the decrease of the crystallization peak temperature, while the GO1 ? C5 uniformly dispersed in the iPP matrix. Unexpectedly, the relative content of β‐crystal of iPP nucleated with 0.02 wt% GO1 ? C5 reached up to 0.8094, and the crystallization peak temperature was increased by 6.7°C compared with that of pure iPP. Meanwhile, the impact strength, tensile strength and heat deflection temperature of iPP nucleated with 0.02 wt% GO1 ? C5 increased by almost 45.86%, 2.03% and 7.7°C, respectively. The iPP nucleated with GO1 ? C5 obtained a balance between stiffness and toughness and the thermo‐mechanical property of nucleated iPP was improved.     

Simply Applicable Method for Microplastics Determination in Environmental Samples

Microplastics (MPs) have gained significant attention in the last two decades and have been widely researched in the marine environment. There are, however, less studies on their presence, routes of entry, and impacts on the biota in the soil environment. One of the main issues in the study of MPs is a lack of standardized methods for their identification in environmental samples. Currently the most commonly used techniques are thermal desorption gas chromatography–mass spectrometry (GC–MS) methods and pyrolysis followed by GC–MS. In this study, headspace-solid phase microextraction followed by GC–MS is proposed as a simple and widely applicable method for the determination of commonly present polymer MPs (polyethylene terephthalate, polystyrene, polyvinyl chloride, polyethylene, and polypropylene) in environmental samples, for analytical laboratories with basic equipment worldwide. The proposed method is based on the identification of compounds, which are formed during the well-controlled melting process of specific coarse (1–5 mm) and fine fraction (1 mm–100 μm) MPs. The method was upgraded for the identification of individual polymer type in blends and in complex environmental matrices (soil and algae biomass). The successful application of the method in complex matrices makes it especially suitable for widescale use.     

石蜡/膨胀石墨/石墨烯复合相变储热材料的制备及性能

以石蜡(PA)作为相变储热材料、 膨胀石墨(EG)作为主导热材料和支撑材料, 石墨烯气凝胶(GA)作为导热增强材料和辅支撑材料制备了PA/EG/GA复合相变材料, 研究了GA添加量对复合相变材料相变温度、 相变潜热、 导热性能以及循环稳定性的影响. 结果表明, 所制备的80%PA-17%EG-3%GA复合相变材料导热性能良好, 循环稳定性出色. 与80%PA-20%EG复合材料相比, 该材料的相变温度、 相变潜热以及循环稳定性无明显变化, 但导热系数由4.089 W/(m·K)提升到了5.336 W/(m·K), 显示出良好的应用前景.     

Deformation Temperature and Lamellar Thickness Dependency of FormⅠto Form Ⅲ Phase Transition in Syndiotactic Polypropylene during Tensile Stretching

Phase transition from form Ⅰto form Ⅲ in syndiotactic polypropylene crystallized at different conditions during tensile deformation at different temperatures was investigated by using in situ synchrotron wide angle X-ray diffraction technique. In all cases, the occurrence of this phase transition was observed. The onset strain of this transition was found to be crystalline thickness decided by crystallization temperature and drawing temperature dependent. The effect of drawing temperature on this phase transition is understood by the changes in mechanical properties with temperature. Moreover, crystalline thickness dependency of the phase transition reveals that this form I to from III phase transition occurs first in those lamellae with their normal along the stretching direction which have not experienced stress induced melting and recrystallization.     

膨胀石墨/聚苯胺/Fe_3O_4复合材料的制备及吸波性能

采用原位聚合方法制备了膨胀石墨/聚苯胺(EG/PANI)复合材料,将Fe_3O_4负载于EG/PANI表面,得到具有电磁吸收性能的EG/PANI/Fe_3O_4复合材料.通过扫描电子显微镜(SEM)、X射线衍射仪(XRD)、傅里叶变换红外光谱仪(FTIR)及矢量网络分析仪(VNA)等对复合材料的形貌、成分和吸波性能进行了研究.吸波性能分析结果表明,当掺杂浓度为0.05 mol/L,匹配厚度d=2 mm时,样品的最小反射损耗(RLmin)在8.64 GHz处达到-37 dB.随着掺杂浓度的增加,最小反射损耗峰向低频移动,对应的匹配厚度逐渐变厚.材料的介电弛豫极化、涡流损耗及λ/4模型的干涉相消现象出现的双峰,使EG/PANI/Fe_3O_4复合材料在电磁波吸收领域有一定的应用前景.     

Surface Modification of Polypropylene by Ethylene Plasma and Its Induced β-Form in Polypropylene

This study aims to investigate the chemical structure and morphology of plasmapolymers produced by deposition of ethylene on the surface of polypropylene. The deposition films(sediments) of ethylene plasma on the surface of polypropylene are nonuniform, and the characterization results indicate the existence of hydroxyl groups and aldehyde(or ketone) groups in the sediments. The sediment of ethylene plasma on the polypropylene surface could induce the growth of β-form crystals in the surface layer of polypropylene.     

原位X射线研究拉伸过程中间规聚丙烯晶体熔融与晶体取向关系

间规聚丙烯熔体(sPP)淬冷至液氮温度并保持5 min, 于20, 40, 80, 120 ℃下等温退火10 h, 制备出具有不同片晶厚度的样品. 在室温条件下, 利用原位X射线在线研究sPP样品拉伸过程中应力诱导的晶体熔融和晶体取向关系. 结果表明, 在单轴拉伸过程中, 应力导致的晶体熔融和晶体取向同时发生, 即两者在同一应变、 同一应力下同时发生, 这一特性不受片晶厚度的影响. 随着片晶厚度的增加, 晶体熔融和取向需要的临界应力不断增大, 在所研究范围内, 该临界应力的增加和片晶厚度基本呈线性关系. 另外, 随着片晶厚度增大, 样品的弹性模量、 屈服强度和应变硬化模量均有一定程度的增大.     

去氢枞酸类成核剂改性聚丙烯的非等温结晶动力学研究

对以去氢枞酸盐为成核剂的聚丙烯非等温结晶动力学进行了研究，用修正Avrami方程的Jexiorny法和莫志深法进行处理。结果表明：修正Avrami方程的Jeziorny方法和莫志深法都适用于去氢枞酸类成核剂改性的聚丙烯的非等温结晶动力学。在同样的降温速率下纯聚丙烯的t1/2比成核聚丙烯的t1／2要长，当降温速率为20K/min时，纯聚丙烯和成核聚丙烯的t1/2分别为0．78min和0．51min。同时从莫志深法得到的F(T)结果可以看出，达到相同的结晶度时纯聚丙烯所需的降温速率要大于成核聚丙烯所需的降温速率，说明成核剂的加入提高了聚丙烯的结晶速率。从Jeziorny法求出的纯聚丙烯和成核聚丙烯的Avrami指数分别为4．46和2．77，表明成核剂改变了聚丙烯的结晶成核和生长方式。     

PP／EPO共混体系混容性与结晶结构

WAXD方法测定表明PP/EPO共混体系的结晶度随EPO组份含量的增加而降低,晶胞参数与组份比无关,并计算了第二类晶格畸变。根据PP/EPO的DSC和扭辫实验得出在所有组成下PP/EPO共混体系是不相容的。但在非晶区可能部分相容。