On the use of AES data analysis to determine local enrichments of conversion coating elements at intermetallic particles on rolled Al

In this paper, the behaviour of the industrial applied Ti/Zr conversion coating (CC) pretreatment on rolled automotive aluminium samples (AA5182) is analysed. Due to its nanometre lateral and depth resolution, Auger electron spectroscopy (AES) is used to analyse the CC distribution at surface cathodic intermetallic particles. As a result of its high surface sensitivity, the AES technique is very susceptible to differences in the top contamination layer thickness. It is demonstrated that AES point measurements performed on aluminium model samples coated with 1.5 and 3 nm of Ti (oxide) layer cannot differentiate the two-layer thicknesses if a difference in the top contamination thickness is not taken into account. A data analysis methodology is introduced, based on the ratio of normalized peak areas (enrichment ratios), to eliminate the effect of the contamination layer thickness. The experimental validation of the methodology is performed on the model samples, demonstrating errors of 2% on the enrichment ratios on similar samples with different contamination layer thicknesses, while the conventional spectra quantification results in errors of 49%. The methodology is also theoretically substantiated within certain constraints. By the use of the AES methodology, an enriched Ti and Zr deposition is confirmed at the cathodic intermetallic particles at the surface of the industrial no-rinse CC sprayed automotive aluminium sheet samples.     

Curing behavior and properties of high biosourced epoxy resin blends based on a triepoxy monomer and a tricarboxylic acid hardener from 10-undecenoic acid

Renewable propane-1,2,3-triyl tris(9-(oxiran-2-yl) nonanoate) (EGU, 100 wt% biogenic) and a tricarboxylic acid triglyceride (CGTU) hardener (85.7 wt% biogenic) were synthesized from 10-undecenoic acid (10-UDA) and used to produce epoxy resins with 52–92 wt% biobased carbon. CGTU was prepared by thermally activated thiol-ene coupling of thioglycolic acid onto propane-1,2,3-triyl tris(undec-10-enoate), (GUD) in the absence of solvent. The characterized CGTU was used as a green hardener of blends based on EGU and a conventional bisphenol A-based epoxy pre-polymer (DGEBA) at various mass percentages (0–100 wt%) with an stoichiometric epoxy/acid equivalent ratio. Calorimetric studies revealed higher peak temperature, lower reaction heats, and longer gelation times in resins with high EGU proportion, evidencing the lower reactivity of aliphatic EGU compared with aromatic DGEBA. Cured resins were yellowish transparent rubber-like materials with glass transition temperatures (Tg) varying from −14 °C to −42 °C and tensile strength in the range of 1750 kPa–790 kPa, for 0 and 100 wt % EGU, respectively. The soluble fraction of all resins was less than 4.3%, reflecting a high level of crosslinking. Thermosets with high biobased content showed both UV-light protection and visible light transparency.     

Biomimetic design of amphiphilic polycations and surface grafting onto polycarbonate urethane film as effective antibacterial agents with controlled hemocompatibility

The synthetic polycations are ideal candidates as antimicrobial agents, because they resemble natural antimicrobial peptides, but to render hemocompatibility to these materials is a great challenge. Herein, we used 2‐(tert‐butyl‐aminoethyl) methacrylate (TBAEMA), to synthesize its homopolymer and pegylated random and diblock copolymers with polyethyleneglycol methacrylate (PEGMA, M_n = 360 Da) by single‐electron transfer–living radical polymerization (SET‐LRP). In the second step, the secondary amino groups in the precursor polymers were quaternized with iodomethane and bromohexane, to obtain three series of quaternized polymers. The antimicrobial properties of these quaternized polymers were evaluated against Escherichia coli (E. coli), by studying the minimum inhibitory concentrations (MICs) which ranged between 32 and 200 mg L^?1 and showed higher values for the quaternized random than the diblock copolymers. In addition to, we have also demonstrated the grafting of these polycations onto polycarbonate urethane film surfaces, which showed good killing efficacy against E. coli. Furthermore, the hemolysis of these materials was investigated against human red blood cells, which indicated that except the quaternized homopolymers that showed highest hemolysis, all other amphiphilic polycations exhibited very low hemolytic activity. Therefore, our designed materials with controlled structures and functionality, synthesized from cheaply available resources could serve as useful agents in the field of biomedicines and implantable materials. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3166–3176     

Chain transfer agents in cationic photopolymerization of a bis‐cycloaliphatic epoxide monomer: Kinetic and physical property effects

The effects of chain transfer agents (CTA) on cationic ring‐opening polymerization of 3,4‐epoxycyclohexylmethyl‐3′,4′‐epoxycyclohexane carboxylate (EEC) were explored. EEC was polymerized in the presence of various CTAs, and epoxide conversions monitored via Raman spectroscopy. Polymer films were prepared and analyzed by dynamic mechanical analysis. Many of the organic alcohols studied greatly enhanced epoxide polymerization rates and conversion levels. The gel fraction of polymer specimens decreased rapidly with increasing amounts of octanol (gel fraction >90% up to 0.3 equiv OH) but remained high with increasing amounts of 1,2‐propanediol (gel fraction >90% up to 0.6 equiv OH). Increasing the size of primary alcohols had little effect on the polymerization rates and conversions. The polymerization rate decreased with increasing alcohol substitution (1°>2°>3°). Acidic alcohols had very low impact on conversion and polymerization rates relative to the neat epoxy resin. The glass transition temperature was inversely related to the size and amount of CTA. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Broadband and high efficiency metal multi-layer dielectric grating based on non-quarter-wave coatings as a reflective mirror

This article deals with designing a broadband and high efficiency metal multi-layer dielectric grating (MMDG) used to compress and stretch an ultrashort laser pulse. The diffraction characteristics of the MMDG are analysed by using the rigorous coupled-wave method. The multi-layer dielectric used as the reflective mirror is made up of non- quarter-wave coatings. Taking the diffraction efficiency of the 1 order as the value of merit function, the parameters such as groove depth, residual thickness, duty cycle, and reflective mirror are optimized to obtain broadband and high diffraction efficiency. The optimized MMDG shows an ultra-broadband working spectrum with the average efficiency exceeding 97% over 160 nm wavelength centred at 1053 nm and TE polarization. The optimized MMDG should be useful for chirped pulse amplification.     

Grafting onto Wool. XXVII. Graft Copolymerization of MixeD Vinyl Monomers by Use of Ceric Ammonium Nitrate as Redox Initiator

In order to ascertain the effect of a donor monomer, vinyl acetate (VAc), on the graft copolymerization of acceptor monomers, ethyl acrylate (EA) and butyl acrylate (BA), grafting of mixed vinyl monomers (EA + VAc) and (BA + VAc) was carried out on Himachali wool in aqueous medium using ceric ammonium nitrate (CAN) as a redox initiator. Graft copolymerization was carried out at different temperatures for various reaction periods. Percent grafting and percent efficiency were determined as functions of 1) concentration of mixed vinyl monomers, 2) concentration of CAN, 3) concentration of HNO₃ 4) temperature, and 5) reaction time. VAc, the donor monomer, was found to decrease percent grafting of EA and BA onto wool.     

Studies on Melamine Modified Polyesteramide as Anticorrosive Coatings from Linseed Oil: A Sustainable Resource

Melamine modified polyester amide (MPEA) was synthesized by the reaction of linseed oil fatty amide. The resin was further cured at room temperature by polystyrene co‐maleic anhydride (SMA) in different phr (30–80) to obtain MPEA coatings. The probable structure of MPEA was confirmed by FT‐IR, ¹H‐NMR and ¹³C‐NMR spectroscopic techniques. The physico‐chemical characterization of these resins viz. iodine value, saponification value, refractive index, inherent viscosity were carried out by standard methods. MPEA (40 wt%) solution in ethylene glycol monomethyl ether (EGME) was applied on a mild steel strip of standard sizes to study their physico‐mechanical and chemical resistance properties. It was found that coatings of MPEA with 60 parts per hundred of the resin (phr) of SMA showed the best performance in physico‐mechanical and alkali resistance properties. Thermal stability and curing behavior were studied by Thermo Gravimetric Analyses (TGA) and Differential Scanning Calorimetry (DSC), respectively.     

Cure Kinetics of Poly(acrylonitrile-butadiene-styrene) Modified Epoxy–Amine System

The cure kinetics of epoxy based on the diglycidyl ether of bisphenol A (DGEBA) modified with different amounts of poly(acrylonitrile-butadiene-styrene) (ABS) and cured with 4,4′-diaminodiphenylsulfone (DDS) was investigated by employing differential scanning calorimetry (DSC). The curing reaction was followed by using an isothermal approach over the temperature range 150–180°C. The amount of ABS in the blends was 3.6, 6.9, 10 and 12.9 wt%. Blending of ABS in the epoxy monomer did not change the reaction mechanism of the epoxy network formation, but the reaction rate seems to be decreased with the addition of the thermoplastic. A phenomenological kinetic model was used for kinetic analysis. Activation energies and kinetic parameters were determined by fitting the kinetic model with experimental data. Diffusion control was incorporated to describe the cure in the latter stages, predicting the cure kinetics over the whole range of conversion. The reaction rates for the epoxy blends were found to be lower than that of the neat epoxy. The reaction rates decreased when the ABS contents was increased, due to the dilution effect caused by the ABS on the epoxy/amine reaction mixture.     

Silica/Silicone Nanofilament Hybrid Coatings with Almost Perfect Superhydrophobicity

A facile method for the preparation of silica/silicone nanofilament hybrid coatings with almost perfect superhydrophobicity (contact angle=179.8° and sliding angle=1.3°) is presented. The coatings are obtained by dip‐coating of silica nanoparticles, followed by chemical vapor deposition of silicone nanofilaments. Predominant growth of silicone nanofilaments onto aggregated silica nanoparticles generates a two‐tier structure. The effect of silica nanoparticle size on the growth of silicone nanofilaments, along with their anti‐wetting properties and transparency are investigated in detail. Surface roughness and anti‐wetting properties can be simply regulated by controlling the size of silica nanoparticles.