A differential scanning calorimetry method to determine the isothermal crystallization kinetics of cocoa butter

This research aimed to reduce the variability on the data obtained from differential scanning calorimetric (DSC) analysis of the isothermal crystallization kinetics of cocoa butter.

To enable transformation of the DSC crystallization peak to a sigmoid crystallization curve, the DSC peak area has to be integrated. Usually, the start and end points of the crystallization peak are determined visually. The result of this visual determination appeared to be very much dependent on the operator, but also differed considerably when the same operator performed the integration several times. By proposing an objective calculation algorithm to determine the start and end points of integration, the variability caused by the operator during the integration procedure could be eliminated. Furthermore, sample preparation and the DSC heating protocol to melt the sample prior to crystallization were studied. Three heating protocols (65 °C for 15 min, 65 °C for 30 min and 80 °C for 15 min) were compared and it was shown that holding at 65 °C for 15 min was sufficient to eliminate any influence of sample history. Two different sample preparation procedures were compared and it appeared that a change in sample preparation procedure had a significant influence on the measured crystallization process. It is thus important to keep this method constant to eliminate the variability caused by it.     

Decay kinetics of the green emission in tungstates and molybdates

Luminescence characteristics of a number of undoped and variously doped PbWO₄ crystals were studied at 0.4–400 K by the time-resolved spectroscopy and compared with those of ZnWO₄,CdWO₄ and PbMoO₄ crystals. Two types of green emission centres are detected in PbWO₄ crystals. The centres of the first type are responsible for the low-temperature 2.3–2.4 eV emission observed under excitation around 3.90–3.95 eV. The structure and parameters of their relaxed excited states were determined. It was concluded that the origin of defects responsible for the green emission of the first type could vary for different crystals. The centres of the second type with the emission around 2.5 eV appear in crystals containing oxygen vacancies after the thermal destruction of Pb⁺-WO₃ centres at T>180 K. Decomposition of the exciton and various defect-related states was also studied, and activation energies of this process were calculated.     

Polymerization of 1,3‐dienes with functional groups. III. Free‐radical polymerization of N,N‐diethyl‐2‐methylene‐3‐butenamide

Free‐radical homo‐ and copolymerization behavior of N,N‐diethyl‐2‐methylene‐3‐butenamide (DEA) was investigated. When the monomer was heated in bulk at 60 °C for 25 h without initiator, rubbery, solid gel was formed by the thermal polymerization. No such reaction was observed when the polymerization was carried out in 2 mol/L of benzene solution with with 1 mol % of azobisisobutyronitrile (AIBN) as an initiator. The polymerization rate (R_p) equation was R_p ∝ [DEA]^1.1[AIBN]^0.51, and the overall activation energy of polymerization was calculated 84.1 kJ/mol. The microstructure of the resulting polymer was exclusively a 1,4‐structure where both 1,4‐E and 1,4‐Z structures were included. From the product analysis of the telomerization with tert‐butylmercaptan as a telogen, the modes of monomer addition were estimated to be both 1,4‐ and 4,1‐addition. The copolymerizations of this monomer with styrene and/or chloroprene as comonomers were also carried out in benzene solution at 60 °C. In the copolymerization with styrene, the monomer reactivity ratios obtained were r₁ = 5.83 and r₂ = 0.05, and the Q and e values were Q = 8.4 and e = 0.33, respectively. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 999–1007, 2004     

Dark cure studies of cationic photopolymerizations of epoxides: Characterization of kinetic rate constants at high conversions

The effective propagation rate constant (k_p; averaged over all the propagating active centers) was characterized for solvent‐free cationic photopolymerizations of phenyl glycidyl ether over the entire range of conversions, including the high conversion regime in which mass transfer limitations become important. The profile for the k_p as a function of conversion was found to exhibit a constant plateau value at low to intermediate conversions, followed by a monotonic increase above a threshold value of conversion. To explain this trend, it is proposed that at high conversion the diffusional mobility of the photoinitiator counterion is reduced whereas the mobility of the cationic active center remains high because of reactive diffusion. Therefore, with increasing conversion, the average distance between the active centers and counterions may increase, resulting in an increase in the propagation rate constant. The profiles for the k_p values were investigated as a function of the temperature, photoinitiator anion, and photoinitiator concentration. As the photoinitiator concentration was increased, the plateau value of the effective propagation rate constant decreased whereas the threshold conversion increased. All of the experimental trends are consistent with the proposed increase in ion separation at high conversions. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4409–4416, 2004     

Dendrimers as scaffolds for multifunctional reversible addition–fragmentation chain transfer agents: Syntheses and polymerization

The synthesis and characterization of novel first‐ and second‐generation true dendritic reversible addition–fragmentation chain transfer (RAFT) agents carrying 6 or 12 pendant 3‐benzylsulfanylthiocarbonylsulfanylpropionic acid RAFT end groups with Z‐group architecture based on 1,1,1‐hydroxyphenyl ethane and trimethylolpropane cores are described in detail. The multifunctional dendritic RAFT agents have been used to prepare star polymers of poly(butyl acrylate) (PBA) and polystyrene (PS) of narrow polydispersities (1.4 < polydispersity index < 1.1 for PBA and 1.5 < polydispersity index < 1.3 for PS) via bulk free‐radical polymerization at 60 °C. The novel dendrimer‐based multifunctional RAFT agents effect an efficient living polymerization process, as evidenced by the linear evolution of the number‐average molecular weight (M_n) with the monomer–polymer conversion, yielding star polymers with molecular weights of up to M_n = 160,000 g mol^?1 for PBA (based on a linear PBA calibration) and up to M_n = 70,000 g mol^?1 for PS (based on a linear PS calibration). A structural change in the chemical nature of the dendritic core (i.e., 1,1,1‐hydroxyphenyl ethane vs trimethylolpropane) has no influence on the observed molecular weight distributions. The star‐shaped structure of the generated polymers has been confirmed through the cleavage of the pendant arms off the core of the star‐shaped polymeric materials. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5877–5890, 2004     

Adsorption Behaviour of 134Cs and 22Na Ions on Tin and Titanium Ferrocyanides

Tin and titanium ferrocyanides were studied as adsorbents for alkali metal ions, viz., ¹³⁴Cs and ²²Na, which represent radioactive wastes. The ferrocyanides were prepared in granular form. The tin version contained 11.2% water, while the titanium version contained 17.7% water. The exchange capacities for Cs⁺ and Na⁺ in the hydrated tin version were about 1.5 and 0.7 meq/g, respectively, while those in the titanium version were 2.2 and 1.2 meq/g, respectively. Drying at 250°C decimated those capacities. The diffusional time constant of Cs⁺ at 25°C, determined via Fick's second law, was of order of magnitude 1 × 10^–3 s^–1, though there were minor differences due to particle size and the form of ferrocyanide. Similarly, the effective diffusivity was of order of magnitude 1 × 10^–8 cm²/s. The titanium version responded slightly faster than the tin version. Likewise, equilibrium measurements in mixtures with sodium nitrate, potassium nitrate, or uranium oxide, showed that the titanium version exhibited significantly greater selectivity for Cs⁺ than did the tin version. Unfortunately, tests of complete elution of the Cs⁺ from the ferrocyanides were mostly disappointing. Work continues on that subject.     

Pseudo-Isotherms Using a Second Order Kinetic Expression Constant

The kinetics of four sorption systems, Cu/tree fern, Pb/tree fern, AB9/activated clay and BR18/activated clay have been studied based on the assumption of a pseudo-second order rate law. Pseudo-isotherms using the pseudo-second order kinetic expression constant have been developed to describe the four liquid-solid sorption systems. The experimental results have been analyzed using a pseudo-Langmuir and a pseudo-Redlich-Peterson isotherm. Both isotherms were found to represent the measured sorption data well. According to the evaluation using the pseudo-Langmuir equation, the monolayer sorption capacities were obtained to be 13.9, 46.6, 124 and 105 mg g^–1 for copper, lead, AB9 and BR18 respectively.     

Synthesis,characterization, and curing kinetics of novel ladder‐like polysilsesquioxanes containing side‐chain maleimide groups

Two ladder‐like polysilsesquioxanes (LPS) containing side‐chain maleimide groups have been synthesized successfully by reacting N‐(4‐hydroxyphenyl)maleimide (HPM) with LPS containing 100 mol % of chloropropyl groups (Ladder A ) and 50 mol % of each methyl and chloropropyl group (Ladder B ). HPM was synthesized by reacting maleic anhydride with 4‐aminophenol, and the resulting amic acid was imidized using p‐toluenesulfonic acid as a catalyst (Scheme 1 ). The LPSs were characterized by Fourier transform infrared (FTIR), ¹H nuclear magnetic resonance (NMR), proton‐decoupled ¹³C NMR, ²⁹Si NMR, wide‐angle X‐ray diffraction (WAXD), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). Characterization indicated that these polymers had ordered ladder‐like structures with possible defects. These polymers were soluble in common solvents at ambient temperature, which suggested that they were not crosslinked. Both the polymers and the HPM were cured, and their kinetics were followed by dynamic DSC. The Ozawa and Kissinger methods were used to calculate activation energies for curing. Curing increased the temperature at which both 5% weight loss and maximum rate of weight loss were observed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4036–4046, 2004     

Kinetic study of the crosslinking reaction of 1,2‐polybutadiene with dicumyl peroxide in the absence and presence of vinyl acetate

The crosslinking reaction of 1,2-polybutadiene (1,2-PB) with dicumyl peroxide (DCPO) in dioxane was kinetically studied by means of Fourier transform near-infrared spectroscopy (FTNIR). The crosslinking reaction was followed in situ by the monitoring of the disappearance of the pendant vinyl group of 1,2-PB with FTNIR. The initial disappearance rate (R₀) of the vinyl group was expressed by R₀ = k[DCPO]^0.8[vinyl group]^−0.2 (120 °C). The overall activation energy of the reaction was estimated to be 38.3 kcal/mol. The unusual rate equation was explained in terms of the polymerization of the pendant vinyl group as an allyl monomer involving degradative chain transfer to the monomer. The reaction mixture involved electron spin resonance (ESR)-observable polymer radicals, of which the concentration rapidly increased with time owing to a progress of crosslinking after an induction period of 200 min. The crosslinking reaction of 1,2-PB with DCPO was also examined in the presence of vinyl acetate (VAc), which was regarded as a copolymerization of the vinyl group with VAc. The vinyl group of 1,2-PB was found to show a reactivity much higher than 1-octene and 3-methyl-1-hexene as model compounds in the copolymerization with VAc. This unexpectedly high reactivity of the vinyl group suggested that an intramolecular polymerization process proceeds between the pendant vinyl groups located on the same polymer chain, possibly leading to the formation of block-like polymer. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4437–4447, 2004     

A nucleophilic substitution reaction in microemulsions based on either an alcohol ethoxylate or a sugar surfactant

A nucleophilic substitution reaction between 4-tert-butylbenzyl bromide and a series of iodide salts has been performed in oil-in-water microemulsions based on either a fatty alcohol ethoxylate or a sugar surfactant. The reaction kinetics was compared with the kinetics of the same reaction performed in a microhomogeneous reaction medium, d-MeOH. Previous results showing a particularly high reactivity in the microemulsion based on the fatty alcohol ethoxylate was confirmed. It was shown that in both microemulsions the reaction rate was almost independent of the choice of counterion to iodide. This indicates that complexation of the cation with the surfactant headgroup, which, in particular, could have taken place with surfactants containing oligooxyethylene chains (a “crown ether effect”), seems not to be of importance.

¹²⁷I NMR studies, as well as quadrupole splitting experiments performed by ²H NMR, indicate that there is a certain accumulation of iodide at the oil–water interface of the microemulsions. It is difficult to draw any quantitative conclusions in this respect, however.

The results obtained in this study, combined with results from previous investigations of the same reaction, indicate that the unexpectedly high reactivity obtained in the microemulsion based on a surfactant containing an oligooxyethylene headgroup is most probably due to the nucleophile being poorly solvated when present in the headgroup layer of such a microemulsion. Poorly solvated anions are known to be highly reactive nucleophiles.