ELECTROSPRAYING/ELECTROSPINNING OF POLY(γ-STEARYL-L-GLUTAMATE): FORMATION OF SURFACES WITH SUPERHYDROPHOBICITY

  Electrospraying/electrospinning of poly(γ-stearyl-L-glutamate) (PSLG) was investigated on a series solutions with different concentrations in chloroform. Field emission scanning electron microscopy (FESEM) and attenuated total reflectance Fourier transform infrared spectroscopy (FT-IR/ATR) were used to characterize the morphology and structure of the electrosprayed/electrospun polypeptide mats. It was found that electrospraying of PSLG with concentrations lower than 16 wt% afforded beads, while microfibers could be electrospun at the concentration of 22 wt%. The hydrophobicity of the electrosprayed/electrospun PSLG mats was investigated with static water contact angle (WCA) and tilt angle measurements. It was demonstrated that the superhydrophobic surfaces of PSLG with WCAs and tilt angles in the ranges of 150°-170° and 16.5°-4.2°, respectively, were obtained through electrospraying/electrospinning process.     

Electrospun cellulose acetate fibers: effect of solvent system on morphology and fiber diameter

This paper reports an investigation of the effects of solvent system, solution concentration, and applied electrostatic field strength (EFS) on the morphological appearance and/or size of as-spun cellulose acetate (CA) products. The single-solvent systems were acetone, chloroform, N,N -dimethylformamide (DMF), dichloromethane (DCM), methanol (MeOH), formic acid, and pyridine. The mixed-solvent systems were acetone–DMAc, chloroform–MeOH, and DCM–MeOH. Chloroform, DMF, DCM, MeOH, formic acid, and pyridine were able to dissolve CA, forming clear solutions (at 5% w/v), but electrospinning of these solutions produced mainly discrete beads. In contrast, electrospinning of the solution of CA in acetone produced short and beaded fibers. At the same solution concentration of 5% (w/v) electrospinning of the CA solutions was improved by addition of MeOH to either chloroform or DCM. For all the solvent systems investigated smooth fibers were obtained from 16% (w/v) CA solutions in 1:1, 2:1, and 3:1 (v/v) acetone–DMAc, 14–20% (w/v) CA solutions in 2:1 (v/v) acetone–DMAc, and 8–12% (w/v) CA solutions in 4:1 (v/v) DCM–MeOH. For the as-spun fibers from CA solutions in acetone–DMAc the average diameter ranged between 0.14 and 0.37 μm whereas for the fibers from solutions in DCM–MeOH it ranged between 0.48 and 1.58 μm. After submersion in distilled water for 24 h the as-spun CA fibers swelled appreciably (i.e. from 620 to 1110%) but the physical integrity of the fibrous structure remained intact.     

Structurally and chemically heterogeneous nanofibrous nonwovens via electrospinning

Homogeneous nonwovens composed of polymer nanofibers of a given diameter are characterized by structural parameters such as the average pore sizes and internal surfaces as well as by transport properties, which are strongly correlated to the fiber diameter at a given porosity. Such nonwovens are used among others for filter applications, protective clothing or as scaffolds for tissue engineering. A frequent requirement is that, to be able to prepare nonwovens optimised for the specific application, one has to find ways to disrupt this strong correlation allowing independent modification of pore diameter, transport properties and internal surface or to induce local chemical and structural heterogeneities within the nonwoven. The route explored in this paper is based on the electrospinning of heterogeneous nonwovens composed of nanofibers with two different average diameters (by a ratio of up to 10 and more) on the one hand and/or different chemical nature on the other hand. Spinning parameters have been optimised to achieve this goal. In addition, nonwovens composed of fibers with circular cross-section and with ribbon-like cross-section have been prepared.     

Electrospun nanofibers of poly（vinyl pyrrolidone）/Eu^3＋ and its photoluminescence properties

Nanofibers of poly（vinyl pyrrolidone） （PVP）/Eu^3＋ with diameters of 300-900 nm were prepared by using sol-gel processing and electrospinning technique. The products were characterized by scanning electron microscope （SEM）, Fourier transform infrared spectroscopy （FT-IR）, and photoluminescence （PL）. The results indicated that, Eu^3＋ was successfully embedded in the onedimensional hybrid nanofibers, and the PVP/Eu^3＋ hybrid nanofibers had favorable photoluminescence properties.     

Partial P-Type Metal Ions Doping Induced Variation of Both Crystal Structure and Oxygen Vacancy Within Cu/SnO2 Metastable Solid Solution Nanofibers for Highly Sensitive C2H2 Sensor

Partial P-type metal ions doping(PPMID) is an alternative method to further enhance the gas sensing performance of N-type metal oxides(NMOs) in contrast to that of P-N metal oxides heterojunctions, but the influences of the introduction of PPMID on the grain size and oxygen vacancies of NMOs have been rarely investigated. Herein, a simple and effective route has been demonstrated to address this problem with Cu²⁺-doped SnO₂ metastable solid solution nanofibers(CSMSSNs) as model and C₂H₂ as target molecule by combining electrospinning and calcination technique. It seems that the introduction of PPMID can also affect crystal structure and oxygen vacancies of NMOs, proven by combining X-ray diffraction(XRD) and X-ray photoelectron spectra(XPS). Thus, PPD, crystal structure and oxygen vacancies have been combined to clarify the enhanced sensing performance of Cu-doped SnO₂ metastable solid solution nanofibers angainst C₂H₂.     

CdSe量子点的光物理性质研究与荧光杂化纤维的制备

半导体纳米晶体(NCs)具有良好的光稳定性,广泛的发射持久性和高消光系数,在过去几年被广泛研究报道,其中,硒化镉半导体纳米晶体(CdSe NCs)被广泛用于电子照明、太阳能发电、光电传感等领域.然而CdSe NCs的电学、热力学和光物理性质具有较强的尺寸依赖性,在传统的制备方法及应用中容易出现晶体表面缺陷和悬空键以及较...     

磷钼酸/聚苯乙烯/聚乙烯醇电纺纤维膜的制备及性能

采用静电纺丝法制备了磷钼酸/聚苯乙烯(PS)/聚乙烯醇(PVA)复合纤维,并将其模压成膜.利用红外光谱(IR)、扫描电子显微镜(SEM)及X射线能谱(EDX)等对复合纤维及其膜的结构与形貌进行表征,并对复合纤维膜的光催化性能、力学性能及在水中稳定性进行测试.结果表明,在复合纤维中磷钼酸的Keggin结构得到保持.PS与PVA质量比为1∶1时,复合纤维形貌最佳,表面光滑,直径较小且分布均匀,复合纤维的直径随着磷钼酸含量的增加而减小.将磷钼酸固载于复合纤维膜上比直接使用具有更高的光催化活性,光照25 min后接近98%的甲基橙降解;复合纤维膜易于回收再利用,5次重复使用后,复合纤维膜没有破损,磷钼酸损失较少,光催化性能无明显下降.复合纤维膜的强度随磷钼酸含量的增加先增大后减小,韧性随PVA含量的增加而增大,随磷钼酸含量的增加而减小.     

Ag修饰的Fe_3O_4/TiO_2复合磁性纳米纤维的制备及光催化性能

通过静电纺丝法制备了含有Fe3O4纳米粒子的TiO2纳米纤维,采用水热法对该纤维表面进行纳米Ag修饰,制备出具有较强磁性和较好光催化性能的复合纤维.采用X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)和紫外-可见光谱(UV-Vis)等对样品的结构和形貌进行表征,并以罗丹明B(Rh B)水溶液降解为模型反应,考察样品在紫外光照射下的光催化性能.结果表明,所制备的TiO2为锐钛矿结构,Fe3O4纳米粒子均匀分布在TiO2纤维中,Ag纳米颗粒比较均匀地分散在磁性TiO2纤维表面.经过纳米Ag修饰后,材料的光吸收能力大为增强,吸收带红移并扩展到可见光区.在紫外光照射40 min后,合成样品对Rh B的降解率达到99.5%.此外,Fe3O4纳米粒子的存在使该材料具有较强的磁性,可通过外加磁场将其分离回收.     

高分散钴氮共掺杂碳纳米纤维氧还原催化剂

过渡金属氮掺杂碳基催化剂已成为替代铂基氧还原反应(ORR)电催化剂的理想选择。本文通过静电纺丝技术制备了高比表面、高度分散的钴原子配位氮掺杂的碳纳米纤维催化剂(Co-N/C)。X射线衍射(XRD)和高分辨率透射电镜(HRTEM)结果证实Co元素高度分散于制备的Co-N/C催化剂中。X射线光电子能谱结果表明N元素主要以吡啶N和石墨N形式存在。该Co-N/C催化剂对ORR反应呈现出较高的电催化活性,其氧还原起始和半波电位分别为0.92 V和0.80 V(相对于标准氢电极),接近于商业化Pt/C催化剂的性能。以制备的Co-N/C催化剂作为阴极,25℃下锌空气燃料电池的开路电位1.54 V、最大功率密度达到了190 m V·cm~(-2)表明该催化剂具有良好的应用前景。     

Antibacterial thermoplastic polyurethane electrospun fiber mats prepared by 3-aminopropyltriethoxysilane-assisted adsorption of Ag nanoparticles

Antibacterial thermoplastic polyurethane(TPU) electrospun fiber mats were prepared by adsorption of Ag nanoparticles(Ag NPs) onto TPU/3-aminopropyltriethoxysilane(APS) co-electrospun fiber mats from silver sol. The use of APS can functionalize TPU fibers with amino groups, facilitating the adsorption of Ag NPs. The effects of p H of silver sol and APS content on Ag NP adsorption and antibacterial activity were investigated. Ag NP adsorption was evidenced by TEM, XPS and TGA. Significant Ag NP adsorption occurred at p H = 3-5. The main driving force for Ag NP adsorption is electrostatic interaction between ―NH3~+ of the fibers and ―COO-derived from the ―COOH group capped on the surfaces of Ag NPs. The antibacterial activity of the Ag NP-decorated TPU/APS fiber mats was investigated using both gram-negative Escherichia coli and gram-positive Bacillus subtilis. The antibacterial rate increases with increasing APS content up to 5% where the antibacterial rates against both types of bacteria are over 99.9%.