Laser cladding of copper with molybdenum for wear resistance enhancement in electrical contacts

Laser cladding of Mo on Cu has been attempted with the aim of enhancing the wear resistance and hence increasing the service life of electrical contacts made of Cu. In order to overcome the difficulties arising from the large difference in thermal properties and the low mutual solubility between Cu and Mo, Ni was introduced as an intermediate layer between Mo and Cu. The Ni and Mo layers were laser clad one after the other to form a sandwich layer of Mo/Ni/Cu. Excellent bonding between the clad layer and the Cu substrate was ensured by strong metallurgical bonding. The hardness of the surface of the clad layer is seven times higher than that of the Cu substrate. Pin-on-disc wear tests consistently showed that the abrasive wear resistance of the clad layer was also improved by a factor of seven as compared with untreated Cu substrate. The specific electrical contact resistance of the clad surface was about 5.6 × 10⁻⁷ Ω cm².     

基于反向传播神经网络的阻抗断层图像重建新方法

电阻抗成像是通过对物体表面电压、电流的测量来重建物体内部阻抗分布或变化图像的一种新颖计算机断层成像技术。阻抗断层图像重建是一种病态的、非线性的逆问题。提出了一种全新的阻抗断层图像重建方法，它利用反向传播神经网络来表征物体内部阻抗变化位置与物体表面电压变化大小的非线性映射关系，从而可以根据对物体表面测量电压的变化先准确定位阻抗变化区域，再用线性近似方法重建阻抗变化图像，这种方法不仅具有一定的抗噪能力，而且成像精度和空间分辨率都大大好于逆投影方法。     

便携式无线人体脂肪率测量仪的设计

生物电阻抗法(BIA)是一种安全非侵入式的、结果可靠有效的人体组成成分(脂肪含量)测量方法。以此为原理,设计了一款便携式无线人体脂肪率测量仪。硬件上,系统以高集成化、低功耗的阻抗测量芯片AD5933为核心,通过蓝牙实现与上位机的无线通信,大大降低了设备的复杂度。软件部分提出一种单频点小阻抗范围的增益系数校准方式,计算量小且容易实现。将新测量仪和欧姆龙体脂仪HBF-358进行对比实验,并作Bland-Altman一致性分析。结果表明,二者的相关系数为0.997。此外,该测量仪还具有易操作、小型化的特点。     

Electrical relaxation studies of olivine type nanocrystalline LiMPO4 (M=Ni,Mn and Co) materials

The olivine type LiMPO₄ (M=Ni, Mn and Co) materials were synthesized by solution combustion technique using glycine as fuel. The structural characterizations were explored to confirm the phase formation of materials. The scanning electron microscope was used to identify the morphology of olivine materials. The local structure and chemical bonding between MO₆ octahedral and (PO₄)^3- tetrahedral groups were probed by Raman spectroscopy. Grain and grain boundaries were contributed for ion relaxation and dc conduction in olivine materials. Two orders of enhancement in ionic conductivity was observed in these olivine materials than the reported value. Among all the explored olivine samples, LiMnPO₄ showed highest enhancement in conductivity due to weak Li–O bonding and largest unit cell volume.     

Effect of bias voltage and electrodes size on the Pd conductance histograms

Conductance histograms of palladium nanocontacts in ultra high vacuum (UHV) were experimentally studied at room temperature using scanning tunneling microscope (STM). Our results show that the resolution of the pure Pd peaks, at 1.8 and around 3G₀, in the histograms, depends on the bias voltage and the electrodes size. The size of the electrodes should be as small as possible to achieve the higher extraction of hydrogen from them and therefore preventing the diffusion of H from the bulk to the nanocontacts during the conductance measurements, particularly at low bias voltage. This could explain why peaks have not been observed previously in the Pd histograms, using STM techniques in UHV.     

Electrochemical Recognition of Chiral Molecules with Poly(4‐bromoaniline) Modified Gold Electrode

A poly(4‐bromoaniline) (PBA) film is electrochemically synthesized on a gold electrode for the recognition of amino acids enantiomers. Scanning electron microscopy measurements show that the porous PBA films are made up of nano‐ribbons. At the PBA modified Au electrode differential pulse voltammograms of L ‐ and D ‐glutamic acids not only have very different current densities, but also produce different waveforms, providing an intuitive way to differentiate the two chiral molecules. Similar results are obtained in analyzing L ‐ and D ‐aspartic acids. Control experiments suggest that the observed sensing behavior arises from synergistic interactions between Au and the PBA film, where polymerization at the meta‐position creates a steric structure needed for differentiating chiral molecules.     

Synergic effect in electrical conductivity using a combination of two fillers in PVDF hybrids composites

The objective of this work was to prepare novel conductive blends of poly(vinylidene fluoride) (PVDF) with polypyrrole (PPy) and to compare their performance with PVDF/multiwall carbon nanotube (MWCNT) composites and novel PVDF/PPy/MWCNT hybrid systems. All the compositions were prepared by melt mixing using a miniature mixer. The mixtures were characterized by Fourier transformed infrared (FTIR), wide angle X-ray diffraction (WAXD), thermogravimetric analyses (TGA), scanning and transmission electron microscopy (SEM and TEM, respectively) and volume electrical resistivity. For the binary PVDF/PPy and PVDF/MWCNT systems, percolation thresholds of 10 and 0.3 wt%, respectively, were found. In the hybrid systems, however, the percolation threshold for each filler was lower than in the binary systems, but the electrical conductivities were always much higher at all concentrations than the conductivities of the binary systems. Therefore, the addition of both fillers had a synergistic effect on the hybrid system conductivity, which was attributed to its morphology: the PPy increased the homogeneity of the MWCNT distribution and decreased the available free volume for the MWCNT; as a result the MWCNT rolled around the PPy particles bridging them through the PVDF matrix, increasing the quantum tunneling effect and thus, the electrical conductivity of the system.     

Electrical conductivity of poly(vinylidene fluoride)/polyaniline blends under oscillatory and steady shear conditions

Blends of poly(vinylidene fluoride) (PVDF) and polyaniline (PAni) were prepared through melt blending in a batch mixer. The morphology, rheological behavior and electrical conductivity were investigated through transmission electron microscopy (TEM) and combined electro-rheological measurements. Through TEM analysis, it was possible to observe that all blends showed typical phase separation with the presence of conductive polymer aggregates. Deformations imposed during a strain sweep caused, not only disturbance of the linear viscoelastic behavior, but also changes in electrical conductivity. The oscillatory shear altered the morphology, breaking the PAni domains into smaller ones. This effect increases the distance between them and, consequently, resulted in a decrease of the electrical conductivity. The measurements under quiescent conditions and steady shear proved that the disturbance in morphology for PVDF/PAni system is non-recoverable. Through combined electrical and rheological measurements, it was possible to achieve good correlation between the electrical and flow behavior of PVDF/PAni blends.     

Synthesis and performance of electroless Ni–P–TiCN composite coatings on Al substrate

Electroless Ni–P and Ni–P–TiCN composite coatings have been deposited successfully on Al substrates. Scanning electron microscopy (SEM) and energy dispersive X‐ray (EDX) techniques were applied to study the surface morphology and the chemical composition of the deposited films. Moreover, X‐ray diffraction (XRD) proved that Ni–P and Ni–P–TiCN deposits have amorphous structures. The properties of Ni–P–TiCN/Al composite films such as hardness, corrosion resistance and electrocatalytic activity were examined and compared with that of Ni–P/Al film. The results of hardness measurements reveal that the presence of TiCN particles with Ni–P matrix improves its hardness. Additionally, the performance against corrosion was examined using Tafel lines and electrochemical impedance spectroscopy techniques in both of 0.6 M NaCl and a mixture of 0.5 M H₂SO₄ with 2 ppm HF solutions. The results indicate that the incorporation of high dispersed TiCN particles into Ni–P matrix led to a positive shift of the corrosion potential and an increase in the corrosion resistance for all aluminum substrates after their coating with Ni–P–TiCN. In addition, Ni–P–TiCN/Al electrodes showed a higher electrochemical catalytic activity and stability toward methanol oxidation in 0.5 M NaOH solution compared with that of Ni–P/Al. Copyright © 2014 John Wiley & Sons, Ltd.     

In vitro dielectrophoresis of HEK cell migration for stimulating chronic wound epithelialization

This article describes a dielectrophoresis (DEP)-based simulation and experimental study of human epidermal keratinocyte (HEK) cells for wounded skin cell migration toward rapid epithelialization. MyDEP is a standalone software designed specifically to study dielectric particles and cell response to an alternating current (AC) electric field. This method demonstrated that negative dielectrophoresis (N_DEP) occurs in HEK cells at a wide frequency range in highly conductive medium. The finite element method was used to characterize particle trajectory based on DEP and drag force. The performance of the system was assessed using HEK cells in a highly conductive EpiLife suspending medium. The DEP experiment was performed by applying sinusoidal wave AC potential at the peak-to-peak voltage of 10 V in a tapered aluminum microelectrode array from 100 kHz to 1 MHz. We experimentally observed the occurrence of NDEP, which attracted HEK cells toward the local electric field minima in the region of interest. The DIPP-MotionV software was used to track cell migration in the prerecorded video via an automatic marker and estimate the average speed and acceleration of the cells. The results showed that HEK cell migration was accomplished approximately at 6.43 μm/s at 100 kHz with 10 V, and F_DEP caused the cells to migrate and align at the target position, which resulted in faster wound closures because of the application of an electric field frequency to HEK cells in random locations.