电场的增强作用对介质膜光栅损伤形貌的影响

研究了电场在介质膜光栅结构中的增强效应对其抗激光损伤阈值的影响.使用傅里叶模式方法计算了电场在介质膜光栅浮雕结构内的分布.数值分析表明：电场在介质膜光栅中增强的最大值为入射光的2倍,其最大的位置出现在相对于入射光对面的光栅槽侧壁。实验测试介质膜光栅样品在1 064 nm和12 ns, 51.2°和TE偏振光入射时,其抗激光损伤阈值为6.61 J/cm2.对损伤形貌进行扫描电镜精确分析,发现介质膜光栅的初始损伤产生于电场在介质膜光栅内增强最大的位置处.     

萘磺酸掺杂对纳米管结构聚苯胺低温电阻率的影响

通过研究用自组装法制备的萘磺酸掺杂的纳米管结构聚苯胺(苯胺与萘磺酸的摩尔比分别为1∶025,1∶05,1∶1,1∶2,1∶3)的电阻率温度依赖关系(测量温区为80—300K),仔细分析聚苯胺的结构形貌特征,提出了变程跳跃隧道穿透混合模型:认为在萘磺酸掺杂的纳米管结构聚苯胺样品中,跳跃和隧穿两种机制同时起作用,载流子沿纳米管传导是变程跳跃过程起主要作用,而载流子在纳米管之间的传导是隧穿过程起主要作用.实验结果表明,不同浓度的萘磺酸掺杂对样品的低温电阻率的影响很大,随着掺杂浓度增加,载流子传导所需克服的能垒C0迅速减小,当掺杂接近饱和时,C0不再减小.实验中还研究了不同形貌对电阻率的影响,结果表明样品中纳米管所占比例的增大有利于载流子传导 关键词： 聚苯胺 纳米管 低温电阻率     

一种简单的光纤光栅电调谐方法

采用较简单的双点源真空蒸发法在光栅外表面上蒸镀一层均匀铝膜,利用电流流过铝膜时产生的电阻热改变光栅的温度而使光栅的中心波长向长波方向发生改变.光栅中心波长的变化与所加电流的平方成正比.实验中用较小的电流(约43mA)获得了较大的波长调谐范围(约4nm),其调谐精度达到2.15×10^-3nm/(mA)².     

高温无铅BaTiO_3-(Bi_(1/2)Na_(1/2))TiO_3正温度系数电阻陶瓷阻抗和介电谱分析

采用固相反应法制备了Y2O3施主掺杂的92 mol%BaTiO3-8 mol%(Bi1/2Na1/2)TiO3(BBNT8)高温无铅正温度系数电阻(positive temperature coe?cient resistivity,PTCR)陶瓷.利用透射电镜观察材料的显微结构,发现陶瓷的显微结构主要包括晶粒和晶界两部分,观察不到明显的壳层结构.进一步利用交流阻抗谱研究了陶瓷的宏观电学性能,发现陶瓷的总电阻是晶粒和晶界两部分的贡献,而晶粒电阻很小,在居里温度以上变化不大,材料的PTCR效应主要是晶界部分的贡献.当温度高于居里温度时,随着温度的升高,晶界介电常数逐渐减小,导致势垒增加,晶界电阻增大,从而产生正温度系数效应.最后,通过测试材料的介电频谱特性,研究计算了陶瓷的室温电阻率.     

高温超导电缆终端预制式应力锥的设计与分析

高温超导电缆终端是高温超导电缆系统的重要组成部分。借鉴常规电缆终端预制式应力锥的设计理论,结合高温超导带材的特殊工作特性,选用耐低温的绝缘材料,对高温超导电缆终端预制式应力锥进行设计。运用有限元分析软件ANSYS对设计的高温超导电缆终端预制式应力锥进行建模和仿真计算,得到终端处的电场和电位分布,并将仿真结果和理论计算结果进行对比分析,验证设计的可行性,为进一步的研究奠定了基础。     

黏滞等离子体中双撕裂模不稳定性的数值模拟研究

本文采用磁流体力学模型,数值研究了平板位形下双撕裂模线性增长率关于等离子体电阻η和黏滞v的定标关系.结果表明,对于有理面间距较大的情况,线性增长率关于电阻和黏滞的指数定标率随着黏滞的增加逐渐由γ∝ η3/5v0的定标变化到γ∝η5/6v-1/6的定标;而对于有理面间距较小的情况,其指数定标率随着黏性的增加从γ∝η 1/3 v0的定标逐渐变化到γ∝η2/3v-1/3的定标.本文还给出了初始阶段对称的双撕裂模的非线性演化,发现在非线性阶段对称的双撕裂模将转化为反对称的双撕裂模,并解释了相应的物理机理.     

Recovery of low temperature electron irradiation-induced damage in n-type gaas

Undoped n-type GaAa was irradiated near 5 and 77 °K with electrons having incident energies between 0.46 and 1.30 MeV. The recovery of the electrical resistivity and the Hall coefficient upon annealing from 4 to 520 °K was monitored. Changes which occurred upon annealing below 200 °K could be reversed by ionizing radiation. A small amount of irreversible ionization-induced recovery was observed after irradiation near 5 °K. Major irreversible recovery stages were centered near 235 (stage I), 280 (stage II) and 520 °K (stage III). Recovery in stage I and II obeyed first order kinetics. The activation energies of stages I and II were determined as 0.72 and 0.83 eV, respectively. The carrier concentration changes per unit irradiation dose corresponding to the three recovery stages differed in their energy dependence indicating that the defects which are removed in stage III have the lowest threshold energy. The carrier concentration changes per unit irradiation dose corresponding to stages I and III were higher for irradiation near 5 °K than for irradiation near 77 °K.     

Induced polarization forward modelling using finite element method and the fractal model

The modeling of induced polarization data from 2D and 3D geological medium was developed. We applied the finite element method and the fractal model to complex resistivity of rocks as an intrinsic electrical property of geological medium. The LU factorization and pre-conditioned complex bi-conjugated gradient method were applied to solve the complex linear equation system. The modeling implemented in this work was efficient and prompt. In addition, the induced polarization survey using the fractal model as intrinsic property of the medium is a promising method for environmental investigation.     

Inspection of the efficiency of conductive clothing examination

High voltage live-line maintenance (LLM) is a commonly applied method worldwide to execute planned works in the grid economically [1]. In case of bare-hand technique workers wear a so-called conductive clothing acting as a Faraday-cage which protects them against the high electric fields during the work.