Direct electrochemistry and electrocatalysis of hemoglobin in gelatine film modified glassy carbon electrode

Direct electrochemical and electrocatalytic behavior of hemoglobin (Hb) immobilized on glass carbon electrode (GCE) containing gelatine (Gel) films was investigated. The characteristics of Hb/Gel film modified GC electrode were performed by using SEM microscopy, UV-vis spectroscopy and electrochemical methods. The immobilized Hb showed a couple of quasi-reversible redox peak with a formal potential of −0.38 V (versus SCE) in 0.1 M pH 7.0 PBS. The formal potential changed linearly from pH 4.03 to 8.41 with a slope value of −52.0 mV pH⁻¹, which suggested that a proton transfer was accompanied with each electron transfer (ET) in the electrochemical reaction. The Hb/gelatine/GCE displayed a rapid amperometric response to the reduction of H₂O₂ and nitrite.     

Determination of copper in medicinal plants used as dietary supplements by atomic absorption spectrometry with direct flame solid analysis

An alternative device for the direct solid analysis (DSA) for copper determination by flame atomic absorption spectrometry (FAAS) is proposed. Copper was directly determined in commercial medicinal plants used as dietary supplements. The determination of copper in solid samples by DSA–FAAS was made by using a conventional air–acetylene flame. Between 0.05 and 1.5 mg of each test, sample was weighed directly into a small polyethylene vial connected to the device used for solid introduction into the flame. Test samples were introduced into the flame as a dry aerosol using a T-quartz cell set between the burner and the optical path. The T-quartz cell has a slit in the superior part by which the solid aerosol passes to the flame. A transient signal, evaluated as integrated absorbance, is produced and it is totally integrated in 2 s. Background signals always presented absorbance values less than 0.1. It was found a characteristic mass of 0.8 ng Cu and absolute limit of detection of 1.2 ng (3 s), or 1.2 μg g⁻¹ if a sample mass of 1 mg was used. Optimized conditions for air flow rate, flame stoichiometry, and so on were established as well. No excessive grinding of the samples was needed and samples with particle of size less than 80 μm were used throughout. No statistical difference between the results from the proposed system and those obtained by sample digestion and determination by conventional FAAS was observed. With the proposed procedure, more than 50 test samples can be analyzed in 1 h and it can be easily adapted to conventional spectrometers for FAAS.     

Development of direct fluorination technology for application to materials for lithium battery

Direct fluorination of 1,3-dioxolan-2-one with elemental fluorine was successfully carried out to provide 4-fluoro-1,3-dioxolan-2-one, which was expected as an additive for lithium ion secondary battery. 4-Fluoro-1,3-dioxolan-2-one was also further fluorinated with elemental fluorine to give three isomers of difluoro derivatives by the same methodology. Another topic is the preparation of trifluoromethanesulfonyl fluoride, an intermediate of lithium battery electrolyte, by the reaction of methanesulfonyl fluoride with elemental fluorine. The use of perfluoro-2-methylpentane as a solvent gave satisfactory selectivity of trifluoromethanesulfonyl fluoride.     

Solid Phase Extraction Chemiluminescence Determination of Methamidaphos on Vegetables

IntroductionDuring recent years,organophosphorus pesticides(OPPs)have been widely used in agriculture becauseof their low environmental persistence and high effec-tiveness.However,they have a high acute toxicity.Trace amounts of OPPs may remain in foodstu…     

Determination of fluoride in complex liquid matrices by electrothermal atomic absorption spectrometry with in-furnace oxygen-assisted ashing

A new chemical method is reported for the determination of total fluoride in complex liquids and suspensions, such as fruit juices, urine, serum and blood. It is based on the formation of the A1F radical in a graphite furnace afterin situ oxygen-assisted ashing of the untreated sample. The absorbance of this radical is measured at 227.45 nm. The method is relatively easy to use and provides a low detection limit (14 ng/ml) and reasonable reproducibility (5–10%).     

Development and validation of a stability-indicating HPLC method for the determination of degradation products in dipyridamole injection

Summary The development and subsequent validation of an isocratic high-performance liquid chromatographic (HPLC) procedure employing ultraviolet (UV) detection for the determination of degradation products in Dipyridamole Injection is reported. The development of this assay involved the evaluation of several factors including buffer type, ionic strength, pH, organic composition, and column type. The described method is simple, reproducible, accurate, and selective. The precision, relative standard deviation (RSD), amongst five sample preparations for total degradation products was not more than (NMT) 10.2 %, while the individual degradation products were NMT 12.1%. Intermediate precision, as determined from fifteen sample preparations, generated by two Analysts on different HPLC systems over three days, exhibited an RSD for total and individual degradation products of 8.2 % and NMT 27.5 %, respectively. The mean absolute recovery of dipyridamole using the described method is 102.1±1. 9%, (mean±SD, n=12) over the concentration range of 0.03 % to 5.0 % of its label claim of 5 mg mL⁻¹. The limit of detection and limit of quantitation were 0.1 and 0.3 μg mL⁻¹, respectively. The linearity of the peak response was verified with respect to dipyridamole concentration over a range of 0.3 and 50 μg mL⁻¹ (0.03 % to 5.0 % label claim). The Standard and Assay Preparations are stable for up to 48 hours at room temperature. The selectivity was evaluated by subjecting the finished product (Dipyridamole Injection) to thermal, acidic, basic, oxidative and fluorescent radiation stress conditions. No interference in the analysis of degradation products was observed, showing the method is stability-indicating.     

基于氮化碳复合材料磁性固相萃取结合高效液相色谱法测定尿液中3种羟基多环芳烃

建立了测定尿液中3种羟基多环芳烃的氮化碳复合材料磁性固相萃取结合高效液相色谱-荧光检测法。所构筑的磁性氮化碳材料，经扫描电子显微镜、X射线衍射仪、振动样品磁强计和比表面积分析仪表征后，用于尿液中3种羟基多环芳烃的富集净化。考察了吸附剂用量、吸附时间、洗脱溶液和洗脱体积（单次洗脱体积×洗脱次数）对萃取效率的影响。结合高效液相色谱-荧光分析，在0.25~250 μg/L范围内线性关系良好（相关系数r=0.999），3种羟基多环芳烃的检出限和定量限分别为0.08和0.25 μg/L，回收率为90.1%~102%，日内和日间精密度分别为1.5%~7.7%和2.2%~8.7%。该本方法简单、快速、高效，可用于尿液中羟基多环芳烃的分析。     

A simple flow injection-reduced volume column system for hemoglobin typing

A flow injection (FI)-reduced volume column system was developed for hemoglobin (Hb) typing to be used as an initial screening method for thalassemia. The column was packed with 140 μl diethylaminoethyl (DEAE)-Sephadex A-50 ion exchange beads. Hb can be separated using Tris–HCl buffer solution with pH gradient 8.5–6.5 and then monitored spectrophotometrically at 415 nm. The hemolysate of 40 blood samples from packed red cells were screened for thalassemia by determining the amount of HbA₂ and HbE present. The proposed system was able to predict positive test results from those samples with β, E-trait and EE homozygous thalassemia, Hb types that were independently identified following the conventional method at the hospital laboratory. Advantages of the proposed system over the conventional column technique include low amount of reagents and blood sample needed, short analysis time and low cost. Each analysis required only 80 μl of 50 times diluted packed cells, which is equivalent to 1.6 μl undiluted packed cells, and it can be completed in only 35 min. This simple FI-reduced volume column system was demonstrated to be an economic alternative system for Hb typing to initially screen some types of thalassemia such as β-trait, E-trait and EE-homozygous which are commonly found in Thailand.     

流动注射光度法同时测定铜基合金中的铝和铁

提出了同时测定铜基合金中铝和铁的流动注射分析法。以０．０４ｍｏｌ／ＬＨＣｌ作载液，铬天青Ｓ为显色剂，通过测定６２８ｎｍ处铝、铁两配合物的吸光度之和及铝配合物的吸光度，实现了两组分的同时测定。在优化的实验条件下，检测限：Ａｌ和Ｆｅ分别为１．６９×１０－３和１．７３×１０－３ｍｇ／Ｌ，Ａｌ浓度在０～０．８ｍｇ／Ｌ；Ｆｅ浓度在０～１．０ｍｇ／Ｌ时服从比耳定律。进样频率为６０样／ｈ，所拟方法用于实际样品分析，获得满意结果。