Measurement and analysis of fission rates in a spherical mockup of uranium and polyethylene

Measurements of the reaction rate distribution were carried out using two kinds of Plate Micro Fission Chamber （PMFC）. The first is a depleted uranium chamber and the second an enriched uranium chamber. The material in the depleted uranium chamber is strictly the same as the material in the uranium assembly. With the equation solution to conduct the isotope contribution correction, the fission rate of 238U and 235U were obtained from the fission rate of depleted uranium and enriched uranium. Then, the fission count of 238U and 235U in an individual uranium shell was obtained. In this work, MCNP5 and continuous energy cross sections ENDF/BV.0 were used for the analysis of fission rate distribution and fission count. The calculated results were compared with the experimental ones. The calculation of fission rate of DU and EU were found to agree with the measured ones within 10% except at the positions in polyethylene region and the two positions near the outer surface. Because the fission chamber was not considered in the calculation of the fission counts of 238U and 235U, the calculated results did not agree well with the experimental ones.     

Mechanistic study of the reaction of methyl peroxy radical (CH3O2) with formaldehyde (CH2O)

ABSTRACT

A direct dynamic study on the reactions of CH₃O₂?+?CH₂O was carried out over the temperature range of 300–1500?K. All stationary points were calculated with the M06-2X/6-311++G(d,p) level of theory and identified for local minimum. The energetic parameters were refined at QCISD (T)/cc-pVTZ and CCSD (T)/cc-pVTZ levels of theory. Three channels were explored and a reaction of hydrogen abstraction from CH₂O by CH₃O₂ was identified as dominant channel which involves the formation of a prereactive complex in the entrance channel. The rate coefficient of the dominant channel was calculated with TST and TST/Eck and the Eckart tunnelling effect is only important over the lower temperature region. The calculated rate coefficient of the dominant channel has positive temperature dependence and agrees reasonably with the available literature data.     

Effects of pressure rise rate on laminar flame speed under normal and engine-relevant conditions

Laminar flame speed (LFS) is one of the most important physicochemical properties of a combustible mixture. At normal and elevated temperatures and pressures, LFS can be measured using propagating spherical flames in a closed chamber. LFS is also used in certain turbulent premixed flame modelling for combustion in spark ignition engines. Inside the closed chamber or engine, transient pressure rise occurs during the premixed flame propagation. The effects of pressure rise rate (PRR) on LFS are examined numerically in this study. One-dimensional simulations are conducted for spherical flame propagation in a closed chamber. Detailed chemistry and transport are considered. Different values of PRR at the same temperature and pressure are achieved through changing the spherical chamber size. It is found that the effect of PRR on LFS is negligible under the normal and engine-relevant conditions considered in this study. This observation is then explained through the comparison between the unsteady and convection terms in the energy equation for a premixed flame.     

Multi-phase transformation kinetics of HSLA steels during continuous cooling: experiments and cellular automaton (CA) simulation

ABSTRACT

Kinetics of multiply ferrite/bainite phase transformation of HSLA steels is investigated by experiments and cellular automaton (CA) simulation. Peak-differentiation method to elucidate the sequential ferrite and bainite phase transformation individually, which is verified by the CA simulation. Such CA modelling executed using classic JMAK theory, but also gives an insight of microstructure evolution of the multi-phase transformation routine on different cooling rate. From that, it enables classic JMAK modelling to capture the detached phase transformation with different growth models and interface-migration mechanisms. Also, we find that the final phase constitution is sensitive to the cooling rate. With increasing the cooling rate, bainite sheaves nucleated at prior austenite boundaries and ferrite/austenite interfaces are significantly facilitated, which seriously inhibits the growth of prior ferrites. The scenario can be interpreted by the CA simulation and the influence of the cooling rate on sequential multi-phase transformation can be also obtained.     

真空条件下LiCl溶液蒸发量随浓度变化规律研究

除湿溶液再生是除湿空调系统的核心过程,为了提高除湿溶液再生效率,以蒸发量作为评价标准,在不同的真空度下对不同浓度LiCl溶液进行再生。对不同再生条件下,溶液的再生情况进行数学模拟及实验研究,并将模拟结果与实验结果进行对比分析,结果表明,实验结果同模拟结果具有相同的变化趋势。在6 kPa和8 kPa的压强下,LiCl溶液的蒸发量随浓度的增大先上升后下降,而在1 kPa的压强下,LiCl溶液的蒸发量随浓度的增大呈现出先下降再升高接着又下降的趋势。     

Multi-wavelength operation of LD side-pumped Nd:YAG laser

A dual-wavelength laser at 1064 nm and 1319 nm is obtained by a single Nd:YAG crystal rod. On the basis of 1064 nm and 1319 nm dual-wavelength laser installation, the second harmonic waves at 532 nm and 660 nm can be achieved by using non-linear frequency conversion technology. When 1064 nm and 1319 nm lasers oscillate simultaneously, the maximum output power is 30.5 W and 8.78 W, respectively. When the 1319 nm laser is restrained, we obtain a 35.6 W maximum output power at 1064 nm and by contrary 11.2 W at 1319 nm. The maximum output powers of 532 nm and 660 nm lasers are 5.34 W and 1.353 W when oscillating simultaneously. With one of them restrained, the maximum output power is 6.72 W at 532 nm and 1.90 W at 660 nm. The optimum repetition rate of the acousto-optic Q-switch is 10.5 KHz and 20.5 KHz for 532 nm and 660 nm lasers, respectively. The optical-to-optical conversion efficiency from the fundamental waves to the harmonic waves is 17.5% and 15.4%. The instability is less than 2%.     

Corrosion and passivation behavior of Mg-Zn-Y-Al alloys prepared by cooling rate-controlled solidification

Highly corrosion-resistant nanocrystalline Mg-Zn-Y-Al multi-phase alloys have been prepared by consolidation of rapidly solidified (RS) ribbons. The relation between corrosion behavior and microstructure evolution of Mg-Zn-Y-Al alloys with a long period stacking ordered phase has been investigated. In order to clarify the influence of rapid solidification on the occurrence of localized corrosion such as filiform corrosion, several Mg_96.75Zn_0.75Y₂Al_0.5 (at.%) alloys with different cooling rates are fabricated by the gravity casting, copper mould injection casting and melt-spinning techniques and their corrosion behavior and microstructures are examined by the salt water immersion test, electrochemical measurements, GDOES, XRD, SEM and TEM. To clarify the effect of aluminium addition on the improvement in corrosion resistance of the alloys, several Mg_97.25−xZn_0.75Y₂Al_x alloys with different aluminium contents are fabricated by consolidating RS ribbons and the formation of corroded films on the Mg-Zn-Y-Al alloys have been investigated. Rapid solidification brings about the grain refinement and an increase in the solid solubility of zinc, yttrium and aluminium into the magnesium matrix, enhancing microstructural and electrochemical homogeneity, which in turn enhanced corrosion resistance. The addition of aluminium to magnesium can modify the structure and chemical composition of surface films and improves the resistance to local breakdown of the films.     

Extreme-value dependence: An application to exchange rate markets

Extreme value theory (EVT) focuses on modeling the tail behavior of a loss distribution using only extreme values rather than the whole data set. For a sample of 10 countries with dirty/free float regimes, we investigate whether paired currencies exhibit a pattern of asymptotic dependence. That is, whether an extremely large appreciation or depreciation in the nominal exchange rate of one country might transmit to another. In general, after controlling for volatility clustering and inertia in returns, we do not find evidence of extreme-value dependence between paired exchange rates. However, for asymptotic-independent paired returns, we find that tail dependency of exchange rates is stronger under large appreciations than under large depreciations.     

间断问题的并行多重网格预条件共轭梯度法求解

首先比较了四种串行多重网格预条件共轭梯度法求解四类典型间断问题时,数值收敛因子与间断类型、间断程度、网格步长的关系;然后,在算法中引入Schwarz并行,探讨了并行算法收敛因子与子区域个数的关系,以及Schwarz并行的获益。给出了详细的性能比较结果。