Thermal study of irradiated polyacetylene films

Polyacetylene films irradiated by-rays up to 100 MRad were studied by means of TMA, DTG and DSC methods.It is shown that as the irradiation dose increases the concentration of topological branching knots into the polymer chains and theT _g values decrease, the total mass loss and the enthalpy of the thermal isomerization reaction also decrease.     

TTT Cure Diagram

Curing reactions of the epoxy system consisting of a diglycidyl ether of bisphenol A (BADGE n=0) and m-xylylenediamine (m-XDA) were studied to calculate time-temperature-transformation (TTT) isothermal cure diagram for this system. Gel times were measured as a function of temperature using solubility test. Differential scanning calorimetry (DSC) was used to calculate the vitrification times. DSC data show a one-to-one relationship between T _g and fractional conversion, a independent of cure temperature. As a consequence, T _g can be used as a measure of conversion. The activation energy for the polymerization overall reaction was calculated from the gel times obtained using the solubility test (41.5 kJ mol^-1). This value is similar to the results obtained for other similar epoxy systems. Isoconversion contours were calculated by numerical integration of the best fitting kinetic model. This revised version was published online in July 2006 with corrections to the Cover Date.     

Texture of zirconia obtained by forced hydrolysis of ZrOCl2 solutions

The structure and surface properties of ZrO₂ strongly depend on its preparation. In the present work the impact of prolonged aging at basic conditions (pH = 9, T = 100°C, t = 48 h), on the phase composition and textural properties, obtained by calcination of the precipitate, was investigated using several techniques conjointly (DTA/TG, DSC, XRD, porosimetry). The thermal effects accompanying the ZrO₂·xH₂O gel formation, the coalescence of the particles and crystallization were evaluated and discussed in terms of the structural differences between the aged and non-aged samples. This revised version was published online in July 2006 with corrections to the Cover Date.     

Pozzolanic properties of a residual FCC catalyst during the early stages of cement hydration

The catalyst used in fluidized catalytic cracking (FCC) units of refineries after several recovery cycles in regeneration units, reduces its activity and it is partially substituted by new catalyst in the process. As it has a high silicon and aluminum oxides content, the pozzolanic properties of a Brazilian FCC spent residual catalyst, used in different substitution degrees to cement, were evaluated by three thermal analysis techniques during the early stages of hydration of a type II Portland cement. NCDTA curves show in real time that the residual catalyst, accelerates the stages of cement hydration. TG and DSC curves of respective pastes after 24 h of hydration evidence the pozzolanic activity of the waste, respectively, by the lower water mass loss during the dehydroxylation of the residual calcium hydroxide and by the lower dehydroxylation endothermal effect. Within the analyzed period, the higher is the cement substitution degree, the higher is the pozzolanic activity of the residual catalyst.     

Hemocompatibility of poly(acrylonitrile-co-N-vinyl-2-pyrrolidone)s: swelling behavior and water states

Hemocompatibility is an essential aspect of blood contacting polymers. Knowledge of the relationship between polymer structure and hemocompatibility is important in designing such polymers. In this work, the effect of swelling behavior and states of water on the hemocompatibility of poly(acrylonitrile-co-N-vinyl-2-pyrrolidone) (PANCNVP) films was studied. Platelet adhesion and plasma recalcification time tests were used to evaluate the hemocompatibility of the films. Considering the importance of surface properties on the hemocompatibility of polymers, static water contact angles were measured by both sessile drop and captive bubble methods. It was found that, on the film surface of PANCNVP with a higher NVP content, adhered platelets were remarkably suppressed and the recalcification time was longer. The total water content adsorbed on the PANCNVP film was determined through swelling experiments performed at temperatures of interest. Differential scanning calorimetry and thermogravimetric analysis were used to probe the states of water in the films. Based on the results from these experiments, it was hypothesized that the better hemocompatibility of PANCNVP films with higher NVP contents was due to their higher free water content, because water molecule exchange at the polymer/liquid interface, facilitated by a high free water content, is unfavorable for the formation of surface bound water, which causes poor hemocompatibility. [diagram in text].     

The effect of humidity on thermal process of zinc acetate

The thermal decomposition of zinc acetate dihydrate Zn(CH₃CO₂)₂·2H₂O in some humidity-controlled atmospheres has been successfully investigated by novel thermal analyses, which are sample-controlled thermogravimetry (SCTG), thermogravimety combined with evolved gas analysis using mass spectrometry (TG–MS) and simultaneous measurement of differential scanning calorimetry and X-ray diffractometry (XRD–DSC). The thermal processes of anhydrous zinc acetate in dry gas atmosphere by conventional linear heating experiment initiated with the sublimation around 180 °C, followed by the fusion and the decomposition over 250 °C. SCTG was useful to interpret clearly the successive reaction because the high-temperature parallel decompositions were effectively inhibited. The thermal behavior changed dramatically by introducing water vapor in the atmosphere and the thermal process was quite different from that in dry gas atmosphere. Zinc oxide (ZnO) was formed only in a humidity-controlled atmosphere, and could be easily synthesized at temperatures below 300 °C. XRD–DSC equipped with a humidity generator revealed directly the crystalline change from Zn(CH₃CO₂)₂ to ZnO. A detailed thermal process of Zn(CH₃CO₂)₂·2H₂O and the effect of water vapor are discussed.     

Synthesis of tridimensional polymers by the copolymerization of phenylglycidylether with aromatic diglycidylethers

Copolymers from phenylglycidylether and several aromatic diglycidylethers are prepared using different ratios of difunctional comonomers and the AIP/ZnCl₂ initiator system. It is found that the percentage of incorporated comonomer depends on the nature of the aromatic moiety introduced. The copolymers are characterized by ¹³C-NMR spectroscopy and turn out to be completely regular and with a high degree of isotacticity (about 80%) that confirms the high degree of regio- and stereoselectivity of the initiator system used. The thermal characteristics of copolymer networks are investigated using differential scanning calorimetry and thermogravimetry. Two fusion endotherms are observed which vary with the degree of crosslinking. By thermogravimetric analyses the thermal stability is found to increase when the crosslinking degree does. © 1994 John Wiley & Sons, Inc.     

Interaction of water with the regenerated cellulose membrane studied by DSC

One to three endothermal peaks atributted to melting of bulk and interfacial water were observed by DSC in the regenerated cellulose — water system. The profiles of thermal effects depend on water content, time of conditioning, film pretreatment and the conditions applied during the preceding freezing-thawing cycles. The occurrence might be deduced of melting-crystallisation processes. A large amount of non-freezable strongly bounded water was also detected. Although cellulose absorbs water quickly after immersion, the structural changes consisting on ordering of polymer fraction occur during further conditioning due to increase in strength of water binding. Using the membranes in the separation module at 90°C causes weakening of these bonds. Differences between interaction of particular cellulose films with water can be detected during the first, the second and the third heating. This revised version was published online in July 2006 with corrections to the Cover Date.     

DETECTION OF T_g BY MODULATED DIFFERENTIAL SCANNING CALORIMETRY

The glassy transition of the polyethylene terephthalate (PET) sampleswhich have been subjected to solvent induced crystallization (SINC) was investigated bymodulated differential scanning calorimetry (MDSC) and density measurement. The dif-ferential of heat capacity signal, d C_p/dT from MDSC, was used to monitor the SINCprocess. It reveals that the T_g temperature shifts to higher value with the advancement ofSINC. When the toluene-immersing time was longer (168h), the detection of T_g becomemore difficult, because some smaller peaks emerged at the lower temperatures and theseare explained as the movement of small segments in the amorphous region. These observedresults are due to the morphology and structure introduced by the SINC process.     

The influence of hydroxyapatite modification on the cross-linking of polydimethylsiloxane/HAp composites

Hydroxyapatite (HAp) was modified by the action of various hydrophobic agents based on silicon-containing compounds. The influence of the type of applied agent on the thermodynamic and kinetic parameters of the cross-linking of poly(dimethyl siloxane)/HAp composites was investigated. All the modified HAp particles became hydrophobic and these samples were used to synthesize the polysiloxane/hydroxyapatite composites (PDMS/HAp). The possible modes of interaction between the hydroxyapatite and hydrophobing agents were discussed. The most probable interaction between hydroxyapatite and the applied hydrophobing agents is hydrogen bonding. PDMS/HAp composites were formed directly in the cell of the DSC and cross-linking was investigated in situ. It was determined that the introduction of hydroxyapatite into polysiloxane matrices changed the enthalpy of cross-linking, as well as the activation energy of cross-linking and reaction order, while the introduction of modified HAp led to thermodynamic and kinetic parameters more similar to those of the cross-linking of unfilled elastomer.