疏水缔合型增稠剂聚(丙烯酰胺-丙烯酸高级酯)的合成及增稠性能研究

采用沉淀聚合法合成了聚（丙烯酰胺－丙烯酸十四酯），聚（丙烯酰胺－丙烯酸十六酯）和聚（丙烯酰胺－丙烯酸十八酯），重点讨论了共聚物中疏水基团数量及疏水基团链长对增稠性能的影响。采用凯达尔定氮法和动态热分析（DMTA）测定了共聚物的组成及玻璃化温度。     

(R)-2-羟基-4-苯基丁酸乙酯的合成

综述了血管紧张素转化酶抑制剂类治疗高血压和充血性心力衰竭药物的关键中间体（R）－2－羟基－4－苯基丁酸乙酯的合成方法。参考文献25篇。     

Microphase separation of PEG-modified urethane acrylate and the swelling behavior of its gels

The viscosity of PEG-modified urethane acrylate (PMUA) showed peculiar behavior in the course of soap-free emulsification. Moreover, the viscosity change with added amounts of water was influenced by the reaction molar ratio of polyethylene glycol (PEG). The rate of increase in viscosity slowed and the ratio of increase in viscosity increased as the reaction molar ratio of PEG increased. This peculiar viscosity behavior was due to the microphase separation between hydrophilic and hydrophobic segments of PMUA, and the orientation of polyoxyethylene groups at O/W interface which influenced droplet size of the soap-free PMUA emulsion. The location of polyoxyethylene groups of this resin at O/W interface was confirmed using the adsorption isotherm measurement of PMUA molecules containing polyoxyethylene groups at water/benzene interface. The microphase separation behavior of PMUA between hydrophilic and hydrophobic segments could apply to the preparation of the PMUA gels containing peculiar structure. PMUA gels were prepared using dioxane (UAG) and the swelling behavior of these gels were compared to that of gels prepared using water (UAHG) in the same medium. In the same medium, the swelling behavior of UAHG gels differed from that of UAG gels because of the difference in the microstructure of gel due to the microphase separation between hydrophilic and hydrophobic segments. This phase separation in the course of gelation in water could be confirmed using contact angle measurement.     

A novel hyperbranched polyester acrylate used for microfabrications

A novel hyperbranched polyester acrylate (HPEA) was synthesized based upon ethylenediamine tetraacetic acid as a “core” molecule, 5‐hydroxyisophthalic acid as an AB₂ monomer, and 2‐hydroxyethyl acrylate as an endcapping reagent. The obtained oligomer has an unsaturation concentration of 4.10 mmol_C?C g^?1 measured by nuclear magnetic resonance and a wide molecular weight distribution of 1.64 measured by gel permeation chromatography. The two‐photon absorption (TPA) photopolymerization of HPEA under the exposure of a Ti : sapphire femtosecond laser with a wavelength of 800 nm was investigated through laser exposure dose‐dependant spatial resolutions of its resins. The TPA photopolymerization thresholds at the range 1.6–4.3 × 10⁷ mJ cm^?2, and exposure dose windows at the range 3.4–4.3 for three formulations were determined. A spatial resolution of 0.85 μm was obtained through the TPA photopolymerization of the formulation containing 1 wt% photoinitiator and 0.3 wt% photoinhibitor. A diffraction grating and real three‐dimensional coupled gear wheel created by TPA photopolymerization were described to demonstrate the unique capability of HPEA in microfabrications. Copyright © 2004 John Wiley & Sons, Ltd.     

壳多糖与丙烯酸丁酯的乳液接枝共聚研究

以十二烷基苯磺酸钠为乳化剂，过硫酸钾－亚硫酸氢钠为引发剂，研究了壳多糖与丙烯酸丁醋的乳液共聚合，结果表明当［Ｋ２Ｓ２Ｏ８］＝［ＮａＨＳＯ３］＝２．５７×１０－３ｍｏｌ·１－１，［ＢＡ］＝０．６８ｍｏｌ．１－１，［Ｃｈｉｔｏｓａｎ］＝１９．２ｇ·ｌ－１，在７０℃下反应５小时，共聚反应的接技率和接枝效率均较高．用红外光谱，差热分析，Ｘ射线衍射，扫描电镜对接技共聚物进行了表征，此外测试了共聚物胶乳成膜的机械性能，表明用丙烯酸丁酯对壳多糖进行接枝改性，可提高壳多糖的韧性，扩大其应用范围．     

Preparation of poly(N‐ethyl methacrylamide) particles via an emulsion/precipitation process: The role of the crosslinker

Monodisperse, thermosensitive poly(N‐ethyl methacrylamide) microgel particles were prepared by the batch precipitation/emulsion polymerization of water‐soluble N‐ethyl methacrylamide and the hydrophobic crosslinker ethylene glycol dimethacrylate initiated by potassium persulfate. Particular attention was paid to the effect of the crosslinker agent on the polymerization process (kinetics, conversion, and water‐soluble oligomer content). Particles were characterized in terms of their size distribution and swelling capacity. A polymerization mechanism for the water‐soluble monomer and non‐water‐soluble crosslinker is proposed and discussed on the basis of a combination of both emulsion and precipitation polymerization processes. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1808–1817, 2002     

淀粉接枝丙烯酸/醋酸乙烯酯高吸水性树脂的制备

以过硫酸铵为引发剂,N,N-亚甲基双丙烯酰胺为交联剂,淀粉与丙烯酸/醋酸乙烯酯混合单体通过接枝共聚,制备了吸水及耐盐性能均较好的淀粉接枝丙烯酸/醋酸乙烯酯高吸水性树脂(CGAV)。最佳工艺条件为:淀粉10.0 g,m(混合单体)∶m(淀粉)=4∶1,w(引发剂)=0.3%,w(交联剂)=0.05%,于45℃反应2h~3 h。在最佳工艺条件下制得的CGAV吸去离子水率760 g.g-1,吸0.9%NaC l水溶液率68 g.g-1。     

Polymer-Titanium hybrids obtained by radical polymerization and Sol-Gel process

The possibility to prepare hybrids made by poly(vinyl acetate) (PVAc), poly(methyl methacrylate) (PMMA) and/or poly(ethyl acrylate) (PEtA) with TiO₂ was studied. The processes of polymer formation-radical polymerization and sol-gel process for inorganic network —were achieved simultaneously. Due to a high reactivity of titanium isopropoxide (TIP) in the sol-gel process, a complexant comonomer, allyl acetoacetate (AlAcAc), was used. Covalent bonds between polymer and inorganic chains were obtained by addition of trialkoxysilane derivates with vinyl (VTES) or methacryloyl (MPTS) groups. The presence of TIP inhibits the radical polymerization of vinyl acetate (VAc). The PVAc-TiO₂ hybrids were produced by the sol-gel process of TIP in the presence of pre-obtained PVAc. Except for VTES and MPTS, trialkoxysilane derivates with methyl (MeTES), octyl (OTES) and phenyl (PTES) groups were used. The thermal stability of hybrids is strongly affected by TiO₂ presence and by the type of trialkoxysilane derivates. The thermal stability of PVAc hybrids decreases in the presence of TiO₂ inorganic network. The glass transition temperature of polymers increases in the presence of the inorganic network.     

核-壳型聚丙烯酸酯复合乳液

简述了核-壳型聚丙烯酸酯复合乳液的合成方法、形态及其影响因素与判断方法、结构与性能等方面的研究进展;认为核-壳型复合乳液膜机械性能优良的原因是:核、壳两相间存在的过渡区适当地抑制了二者的相分离。     

水性丙烯酸酯共聚物交联体系的流变性

用旋转粘度计研究了甲基丙烯酸甲酯／丙烯酸丁酯／丙烯酸三元共聚物水性交联体系的流变性，考察了树脂含量、金属鳌合物含量和氨水水化对其流变性的影响。结果表明：三元共聚物水性交联体系呈非牛顿流体流变行为，具有剪切变稀特性；随树脂含量或鳌合物含量增加，体系的增稠能力得以增强；水化不仅可改善体系的增稠性能，而且可增强体系的非牛顿流变性。