Determination of Fibre Pore Structure: Influence of Salt,pH and Conventional Wet Strength Resins

It has been shown, in the present investigation, that the two methods used to investigate the pore size distribution of unbleached chemical pulps, i.e. inverse size exclusion chromatography (ISEC) and nuclear magnetic resonance (NMR), give different average pore radius for the pores inside the fibre wall. This is due to the way in which these experiments are performed and the sensitivity of the methods to different types of pores in the cell wall. It was also shown that the two methods gave different results when changing the pH and the ionic strength of the pulp suspension. The pore radius, as detected with ISEC, decreased with both increasing ionic strength and decreasing pH, indicating a loose structure of the exterior of the fibrillar network. However, the pore radius as detected with NMR, was virtually unaffected when increasing the ionic strength, indicating a very rigid structure of the interior of the fibre wall. Decreasing pH though, lead to a decrease in pore radius indicating that upon protonation of the carboxylic groups in the fibre wall, the electrostatic repulsion is diminished and the average pore radius decreases. The NMR technique was also used to study wet strength aid penetration into the fibre wall. It was shown that wet strength aids with a small molecular weight, penetrated the fibre wall, as detected by a decrease in pore radius. It was also shown that addition of different wet strength aids increased the tensile index of the sheet and decreased the fibre strength, measured as zero span-strength of the sheets.     

Synthesis of persulfate containing poly (N-vinyl-2-pyrrolidone) (PVP) hydrogels in aqueous solutions by γ-induced radiation

The effect of ⁶⁰Co γ-irradiation on aqueous solutions of poly(N-vinyl-2-pyrrolidone) (PVP) in the presence of persulfate anion has been investigated. The gelation dose of PVP and persulfate containing PVP aqueous solutions has been determined. At low concentrations of persulfate (1.00–3.50%), gelation percentages exhibited a decreasing trend by increasing persulfate content in aqueous solutions of the polymer. The gelation doses of persulfate containing polymer solutions were calculated by the Charlesby–Pinner equation. It was observed that the gelation dose values were shifted to higher values by increasing persulfate concentration in solution. The ratio of the chain scission and crosslinking yields (G(s)/G(x)) was also determined. The results showed that the G(s)/G(x) ratios were smaller than one for PVP aqueous solution system, whereas those obtained for persulfate containing PVP aqueous solutions were higher than unity. The results implied that the chain scission of polymer is more effective than crosslinking in the presence of persulfate. Mechanism of the crosslinking and/or degradation and structure–property relationship of PVP and PVP/persulfate hydrogel systems were investigated by Fourier transformation infeared and thermal analysis (differential scanning calorimetry, thermal gravimetric analysis and differential thermai analysis) methods.     

Crosslinking and characterization of commercially available poly(VDF-co-HFP) copolymers with 2,4,4-trimethyl-1,6-hexanediamine

Fluorinated copolymers are well known for their large range of applications. These applications can be improved by grafting or crosslinking of several agents. The mechanism of crosslinking of hexamethylene diamine and 2,4,4-trimethyl-1,6-hexanediamine is well known and occurs in four different steps. To elaborate a film of commercially available poly(VDF-co-HFP) copolymer crosslinked by 2,4,4-trimethyl-1,6-hexanediamine, a step of press cure under air is necessary. Temperature, time and pressure were optimised by regarding the solubility of the press cured films, the mechanical properties, the swelling rate in methyl ethyl ketone, and the degradation of the films. The best temperature, time and pressure for press cure were 150 °C, from 15 to 30 min, and 20 bars, respectively. Other properties of crosslinked poly(VDF-co-HFP) copolymers containing 10 mol.% and 20 mol.% of HFP were characterized. First, all films were insoluble in concentrated HCl. Secondly, swelling rates of different amounts of diamine crosslinked copolymers were measured in ethylene carbonate/dimethyl carbonate and in methyl ethyl ketone; it was proved that the higher the molar percentage of diamine, the higher the crosslinking density, so the lower the swelling rate. Concerning thermal properties, glass transition temperature mainly increased when the amount of diamine increased. Thermal stability measurements showed a higher decomposition temperature when the percentage of diamine was very low (5 mol.%). Finally, mechanical properties were measured by dynamic mechanical analysis; the storage tensile modulus (E′) of a diamine crosslinked Kynar^® copolymer versus temperature exhibited a high drop because Kynar^® was a highly amorphous copolymer. Moreover, the higher the amount of diamine, the higher the rubbery modulus.     

低浓度HPAM/AlCit交联体系的27Al NMR研究

用27Al NMR谱研究了高分子量低浓度的部分水解聚丙烯酰胺(HPAM)与柠檬酸铝(AlCit)体系交联反应过程中Al的化学位移和Al的自旋-晶格弛豫时间的变化. 结果表明, HPAM与AlCit反应后, 与HPAM分子链上的羧基发生配位交联的Al的化学位移向低场移动, 而不参与交联反应的AlCit分子结构中Al的化学位移基本不变. HPAM/AlCit交联体系中存在三种形态的Al, 分别对应三种不同的自旋-晶格弛豫时间. 当HPAM的质量浓度≤200 mg/L时, HPAM与AlCit反应过程中交联态Al的自旋-晶格弛豫时间τ13随反应进行变小, HPAM与AlCit主要发生分子内交联反应. 当HPAM的质量浓度≥250 mg/L时, HPAM与AlCit反应过程中交联态Al的自旋-晶格弛豫时间τ13随反应进行变大, HPAM与AlCit主要发生分子间交联反应.     

合成云母蒙脱石及其交联物在乙醇氨化反应中的催化行为

用水热法合成了云母蒙脱石,并与羟基铝齐聚物交联,DTA和IR结果表明,由于柱的引进,高温焙烧时层内八面体上羟基脱除变得较为容易。由NH_3-TPD和吡啶吸附测得的表面酸性表明Al-CLS具有较SMM更多的弱酸和强酸中心。催化剂上弱酸中心有利于醇的脱水,而吸附在强酸中心上的NH_3有利于醇的胺化。     

Viscoelastic and thermal characterization of crosslinked PVC

Soft PVC is employed for the manufacturing of a wide range of products with different properties and a relatively low cost. The utilization of soft PVC is restricted by the poor thermal, chemical and mechanical resistance properties. Also, plasticizer migration can modify the properties or can make useless the materials for some applications because of toxicity or a general loss of properties. PVC crosslinking is the most effective way to improve mechanical and transport properties of rigid or flexible PVC at high temperatures, but at the same time the thermal stability of PVC may be significantly reduced. In this work, the crosslinking reaction of plasticized poly(vinyl chloride) (PVC) through difunctional amines was studied. The mechanisms involved in the crosslinking reaction were explained by Fourier transform infrared (FTIR) analysis. The thermal activated crosslinking reaction was studied by cone and plate rheometry, analyzing the evolution of viscoelastic properties of the suspension as a function of time and temperature. The effect of the addition of crosslinking agents on the thermal stability of the polymer was studied by thermogravimetric analysis (TGA), which revealed that crosslinking reactions promote thermal degradation phenomena in the polymer matrix. This is attributed to the formation of HCl and other species promoting polymer degradation during crosslinking, thus leading to higher weight loss during thermal treatment with respect to unmodified PVC plastisols. This was also confirmed by an evident yellowing after crosslinking, especially at higher temperatures.     

Influence of plasticizers and crosslinking on the properties of biodegradable films made from sodium caseinate

Plasticized protein films were prepared by the casting method from water solution of sodium caseinate and plasticizers with the aim to obtain environmentally friendly materials for packaging applications. Mechanical properties (tensile strength, elongation and Young’s modulus) of caseinate based films were determined versus ratio of protein to plasticizer, plasticizer type and relative humidity conditions. Among the different polyol-type plasticizers tested, glycerol (Gly) and triethanolamine (TEA) were the most efficient for the improvement of mechanical properties (high strains for low stresses). Further, chemical crosslinking between formaldehyde (HCHO) and free amino groups (ε-NH₂) of sodium caseinate was performed to increase water resistance of TEA plasticized films. Optimal mechanical properties, i.e. elastic modulus of 105 MPa, tensile strength of 8-9 MPa for elongation at break about 110-125% were obtained for HCHO/ε-NH₂ ratios higher than 1.35. Protein specific water solubility was determined from a 280 nm absorbance. For convenient crosslinker (HCHO) content sodium caseinate solubility can be lowered to less than 5 wt% after 24 h immersion in water.     

Monodisperse Crosslinked Microsphere Polymer Particles by Dispersion Copolymerization of Glycidyl Methacrylate and Divinylbenzene

Monodisperse polyglycidyl methacrylate (PGMA) microsphere particles crosslinked with divinylbenzene crosslinker were prepared by single-stage dispersion copolymerization in ethanol medium. 1 wt% of DVB was successfully incorporated due to the costabilizing effect of GMA as a surface-active monomer. This behavior may indicate that the fast formation of stable primary particle leads to monodispersity. The average particle sizes and the particle size distributions increased with the DVB crosslinker concentration. The effects of two different variables (initiator concentration, crosslinker concentration) on the rate of dispersion copolymerization have been investigated. With the initiator concentration, the polymerization procedure mainly depended on the dual natures of general dispersion polymerization, in the crosslinked state. Up to 1 wt% DVB, the particle growth was controlled by the monomer diffusion from the continuous phase into the particle phase.     

Synthesis and Polymerization of N-(L-Menthylcarboxylatomethyl)maleimide

A new type of optically active N-(L-menthylcarboxylatomethyl)maleimide (MGMI) was synthesized from maleic anhydride, glycine, and L-menthol. Radical homopolymerization of MGMI was performed at 50°C for 24 h to give optically active polymer having [α]_D = -57°. Radical copolymerizations of MGMI (M ₁) were performed with styrene (ST, M ₂), methyl methacrylate (MMA, M ₂) in benzene at 50°C. From the results, the monomer reactivity ratios (r ₁, r ₂) and the Alfrey-Price Q, e values were determined as follows: r ₁ = 0.16, r ₂ = 0.006 for the MGMI-ST system; r ₁ = 0.15, r ₂ = 1.65 for the MGMI-MMA system, and Q ₁ = 0.72, e ₁ = 1.59 calculated from the MGMI-MMA system. Anionic homopolymerizations of MGMI were also carried out. Chiroptical properties of the polymers were investigated.     

Effect of partial crosslinking on morphology and properties of the poly(β-hydroxybutyrate)/poly(d,l-lactic acid) blends

Poly(β-hydroxybutyrate) (PHB) is a bio-based and biodegradable aliphatic polyester, however its application is limited by some disadvantages such as high price, brittleness, poor processability and low melt-strength due to serious thermal degradation. Partial crosslinking initiated by dicumyl peroxide (DCP) was applied in this work to improve the performance of poly(β-hydroxybutyrate)/poly(d,l-lactic acid) (PHB/PDLLA) blends. The partial crosslinking of the blends and its effect on the properties, morphology, rheology and thermal behavior of the blends were investigated. The tensile strength and impact toughness of the PHB were increased by incorporation of the PDLLA, which were improved further after the partial crosslinking because of an increased compatibility between the PHB and the PDLLA phases. The rheological study revealed that the storage modulus (G′) and complex viscosity (η*) of the blends were increased after addition of the DCP. On the other hand, the crystallization of PHB in the blends was restricted to a certain extent by the formation of partially crosslinked network while its crystal form was not modified.