Dual effects of fullerene doped to holographic polymer dispersed liquid crystals

Doping of conductive fullerene particles to the formulation of conventional holographic polymer dispersed liquid crystal‐induced dual effects of reducing both droplet coalescence and operating voltage. Fullerene induced an induction period which otherwise does not exist, followed by a gradual increase of diffraction efficiency to a saturation value being increased with increasing fullerene content. The increased diffraction efficiency was caused by the decreased droplet coalescence which was due to the hindered migration of LC by the fullerene particles. On the other hand, doped fullerene particles augmented the conductivity of polymer phase and hence the local electrical field imposed on LC droplet, which overcome the threshold for driving and reduced operating voltage and response times. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5590–5596, 2007     

Co@SiO2核壳式纳米磁性粒子的合成、性质表征及在细胞分离和细胞芯片上的应用

合成了Co@SiO2核壳式纳米粒子,并采用透射电镜(TEM)、X射线衍射(XRD)、扫描电镜(SEM)和振动样品磁强计(VSM)对其形状、尺寸、荧光及磁特性进行了表征,探讨了其在细胞分离和细胞芯片上的应用和原理.     

Adhesion studies of latex film surfaces on the meso- and nanoscale

In this paper the effects of surface roughness and annealing temperature (T) of latex coating films on adhesion are discussed for the different stages of the film formation process. The surface free energy of latex films was assessed in terms of practical work of adhesion (W) (or adherence) using a custom-built adhesion-testing device (ATD), atomic force microscopy (AFM), and contact angle measurements. For preannealed latex films surface roughness averages (R_a) were determined from AFM height images and were related to the values of W obtained from ATD measurements at room temperature. The results obtained using these tests exhibiting surface behavior on different length scales indicate a dependence of the measured adhesion on surface roughness and temperature, as well as on the length scale of the measurements.First preannealed samples were studied, which were obtained by heat treatment above the respective glass transition temperatures (T_g). Increasing the temperature of preannealing resulted in a decrease of the adherence observed in ATD experiments at room temperature. However, on the nanoscale, using AFM, no significant variation of the adherence was observed. This observation can be explained by roughness arguments. Preannealing decreases roughness which results in lower adherence values measured by ATD while for essentially single asperity AFM experiments roughness has an insignificant effect. Specimens were also annealed over a constant period of time (90 min) at different temperatures. At the end of the heat treatment, adhesion was measured at the treatment temperature by ATD. The amplified effect of temperature observed in this case on adherence is attributed to the combination of roughness decrease and increasing test temperature. In a third set of experiments completely annealed samples were studied by ATD as well as by AFM as a function of temperature. With increasing T values ATD showed a decrease in adherence, which is attributed to a decreasing surface free energy of the annealed films at elevated T values. AFM, on the other hand, showed an opposite trend which is assigned to increasing penetration of the tip into the tip/wetting polymer samples versus increasing temperature. Finally, annealing isotherms as a function of time were investigated by ATD in situ at different temperatures. This last set of experiments allowed us to optimize annealing time and temperature to achieve complete curing.     

The structure of monolayer SiO2 on Mo(1 1 2): A 2-D [Si-O-Si] network or isolated [SiO4] units?

In this letter, atomically resolved scanning tunneling microscopic (STM) images obtained from monolayer SiO₂/Mo(1 1 2) are presented. The results are consistent with a previously proposed structural model of isolated [SiO₄] units based on vibrational features observed by high-resolution electron energy loss spectroscopy (HREELS) and infrared reflection-absorption spectroscopy (IRAS), and oxygen species identified by ultra-violet photoemission spectroscopy (UPS). These results are inconsistent with a structural model that assumes a two-dimensional (2-D) [Si-O-Si] network. These data illustrate that a metal substrate, although coated with an oxide thin layer, can be directly imaged at the atomic-scale with STM.     

改进形态学相关算法以识别高相似度灰度图像

从形态学角度定义了灰度联合图像相似度，提出两种基于位表示法形态学相关算法的改进算法，通过提取位表示法的图像片边缘特征或二元化位表示法的图像片功率谱，以提高位表示法形态学相关算法对高相似度灰度图像的识别能力。     

生长温度对磁控溅射ZnO薄膜的结晶特性和光学性能的影响

采用反应射频磁控溅射方法，在Si (100) 基片上制备了具有高c轴择优取向的ZnO薄膜.利用 原子力显微镜、透射电子显微镜、X射线衍射分析、拉曼光谱等表征技术，研究了沉积温度 对ZnO薄膜的表面形貌、晶粒尺度、应力状态等结晶性能的影响；通过沉积温度对透射光谱 和光致荧光光谱的影响，探讨了ZnO薄膜的结晶特性与光学性能之间的关系.研究结果显示， 在室温至500℃的范围内，ZnO薄膜的晶粒尺寸随沉积温度的增加而增加，在沉积温度为500 ℃时达到最大；当沉积温度为750℃时，ZnO薄膜的晶粒尺度有所减小；在室温至750℃的范 围内，薄膜中ZnO晶粒与Si基体之间均存在着相对固定的外延关系；在沉积温度低于500℃时 ，制备的ZnO薄膜处于压应变状态，而750℃时沉积的薄膜表现为张应变状态.沉积温度的不 同导致ZnO薄膜的折射率、消光系数、光学禁带宽度以及光致荧光特性的变化，沉积温度对 紫外光致荧光特性起着决定性的作用.此外，探讨了影响薄膜近紫外光致荧光发射的可能因 素. 关键词： ZnO薄膜 表面形貌 微观结构 光学常数     

Improvement of the properties of polyarylate reinforced with liquid crystalline polymers

Blends of polyarylate of bisphenol A, PAr, with two commercial main chain liquid crystalline polymers, Vectra A950 and Vectra B950, are studied. From dynamic viscoelastic measurements it is deduced that both systems (PAr/Vectra A950 and PAr/Vectra B950) are immiscible and scanning electron microscopy (SEM) micrographs show the presence of spherical domains of the liquid crystalline polymer when PAr constitutes the matrix. Extrusion capillary measurements reveal that, under conditions of temperature and shear rate similar to those of processing, the viscosity is reduced to approximately 10% of its value when the content of liquid crystalline polymer is only 20%. This great improvement of the rheological properties is observed in both PAr/Vectra A950 and PAr/Vectra B950 blends. The effect of draw ratio on Young's modulus for different compositions is also analyzed, pointing out the reinforcing action of both liquid crystalline polymers on polyarylate: for instance, 20% of Vectra B950 in the blend gives rise to a 700% increase of the modulus of fibres prepared at a draw ratio of 50. SEM of the extrudates reveals that the spherical domains are elongated at the entrance of the capillary giving rise to a microfibrillar morphology which is related to the excellent rheological and mechanical properties of the blends.     

Thermoanalytical procedures to identify the morphology of polycrystalline materials

Polypropylenes of differing morphologies were examined by differential thermal analysis. The problems of reordering during the programmed heating are discussed. Four potential procedures by which the reordering could be inhibited are considered, and three of these are experimentally assessed. Their advantages and deficiencies are identified. Two pretreatments, an etching and a crosslinking, are recognised as able to qualitatively characterise the initial morphology, with a preference for the former. A test to identify the occurrence of reordering is identified. In celebration of the 60^th birthday of Dr. Andrew K. Galwey     

Solved and unsolved problems in surface structure determination

The range of surface structural problems of interest in understanding the physics and chemistry of solid surfaces is reviewed with reference to the available methods and their strengths and limitations. Key challenges being addressed currently concern the achievable precision of measurements and their physical and chemical significance, and the complexity of the problems which may be solved. Past progress and future problems are illustrated with a series of examples ranging from the relaxation of simple clean metal surfaces through complex semiconductor reconstructions to large molecular adsorption and coadsorption systems and complex adsorbate-induced reconstructions. The strengths and limitations of scanning tunnelling microscopy as a complement to true quantitative structural methods are discussed, as is the role of chemical state specificity and elemental specificity in solving complex molecular adsorbate systems.     

Morphology of Nylon-6 blends with styrenic polymers

The morphology of blends of styrenic polymers in a matrix of 75% Nylon-6 prepared in a Brabender Plasti-Corder was examined by scanning electron microscopy. Styrene/acrylonitrile copolymers (SAN) form smaller particles as the AN level increases owing to the corresponding decrease in the SAN–polyamide interfacial tension. Various styrenic polymers containing functional groups, maleic anhydride or oxazoline type, that can react with Nylon-6 during melt processing were added to the SAN phase which also led to a decrease in the particle size owing to the graft copolymer formed in situ. The effects of functional group type, amount of functional groups per chain, amount of functional polymer added, and the miscibility of the styrene/maleic anhydride (SMA) and SAN copolymers on the morphology of the styrenic phase in the Nylon-6 matrix are described. © 1992 John Wiley & Sons, Inc.