复合载体及其制备方法对非晶态Ni-B合金催化剂性能的影响

采用浸渍法及溶胶-凝胶法制备了TiO2-Al2O3复合载体,采用浸渍还原法制备了负载型非晶态Ni-B合金,以糠醛液相加氢制糠醇为探针反应考察了不同载体及复合载体的不同制备方法对非晶态Ni-B合金催化性能的影响.采用等离子发射光谱(ICP)、差示扫描量热法(DSC)、透射电镜(TEM)、H2化学吸附法、程序升温还原(TPR)和程序升温脱附(TPD)等技术研究了负载型非晶态Ni-B合金的负载量、合金组成、热稳定性、粒子大小和形态、活性表面积、还原性能以及吸附性能等.用N2吸附法测定了催化剂及载体的比表面和孔径.研究结果表明,与单一氧化铝载体相比,复合载体负载的Ni-B合金催化活性和选择性明显提高,浸渍法制备的TiO2-Al2O3复合载体负载Ni-B合金的催化性能优于溶胶-凝胶法.主要的原因为复合载体负载的催化剂中Ni含量更高,Ni-B粒子细化导致活性表面积更大,以及催化剂的还原及吸附性能发生改变.     

NO_2-Ni~(2+)-SCN配合物极谱吸附波的研究及痕量NO_2的测定

本文提出了极谱法测定痕量亚硝酸根的一个新体系。在含有Ni~(2+)和SCN~-的稀硫酸底液中,在单扫示波极谱仪上,有一灵敏的亚硝酸根配合物吸附波,峰电位为-0.57V(vs SCE)。一阶导数峰高与亚硝酸根浓度在2×10~(-8)～2×10~(-6)mol/L之间成线性关系。检测限达8×10~(-9)mol/L。回归方程为:Y=0.47x+0.096,相关系数为0.998,相对标准偏差为1.6％。该法具有良好的选择性,尤其是大量硝酸根不干扰测定。成功地应用于实际样品中痕量亚硝酸根的分析。     

Inhibitive detection of benzoic acid using a novel phenols biosensor based on polyaniline–polyacrylonitrile composite matrix

A novel sensitive and stable phenols amperometric biosensor, based on polyaniline–polyacrylonitrile composite matrix, was applied for determination of benzoic acid. The electrochemical biosensor functioning was based on the inhibition effect of benzoic acid on the biocatalytic activity of the polyphenol oxidase (PPO) to its substrate (catechol) in 0.1 M phosphate buffer solution (pH 6.5). A potential value of −50 mV versus SCE, and a constant catechol concentration of 20 μM were selective to carry out the amperometric inhibition measurement. The kinetic parameters Michaelis-Menten constant and maximum current (I_max) in the absence and in the presence of benzoic acid were also evaluated and the possible inhibition mechanism was deduced. The inhibiting action of benzoic acid on the polyphenol oxidase electrode was reversible and of the typical competitive type, with an apparent inhibition constant of 38 μM. This proposed biosensor detected levels of benzoic acid as low as 2 × 10⁻⁷ M in solution. In addition, the effects of temperature, pH value of solution on the inhibition and the interferences were investigated and discussed herein. Inhibition studies revealed that the proposed electrochemical biosensor was applicable for monitoring benzoic acid in real sample such as milk, yoghurt, sprite and cola.     

互通多孔碳/二氧化锰纳米复合材料的原位水热合成及电化学性能

以互通多孔碳（IPC）为载体，水热条件下在碳表面原位反应生成纳米结构的二氧化锰（MnO₂），制备互通多孔碳/二氧化锰纳米（IPC/MnO₂）复合电极材料. 采用扫描电镜（SEM），透射电镜（TEM），X射线衍射（XRD），热重分析（TGA）对其结构进行表征；采用循环伏安法、恒流充放电和交流阻抗对其电化学性能进行研究. 结果表明：生成的MnO₂均匀地负载在碳的表面，形成多层次结构，并且随着温度的升高IPC表面负载的MnO₂由纳米颗粒变为纳米片状结构；MnO₂纳米片具有典型的K-Birnessite 型晶体结构；复合物中MnO₂的含量约为34%（w）. 在100 ℃制备的IPC/MnO₂复合材料在三电极系统中最高比电容达到了411 F·g^-1；随着反应温度的升高,比容量先增长后基本保持不变. 以IPC/MnO₂为正极，活性炭（AC）为负极，1 mol·L^-1 Na₂SO₄溶液为电解液组装成IPC/MnO₂//AC 混合超级电容器，发现IPC/MnO₂电极的电容器其电位窗口从1 V扩展到1.8 V，容量可达86F·g^-1，且表现出良好的电容特性和大电流放电性能.     

互通多孔碳/二氧化锰纳米复合材料的原位水热合成及电化学性能

以互通多孔碳（IPC）为载体，水热条件下在碳表面原位反应生成纳米结构的二氧化锰（MnO₂），制备互通多孔碳/二氧化锰纳米（IPC/MnO₂）复合电极材料. 采用扫描电镜（SEM），透射电镜（TEM），X射线衍射（XRD），热重分析（TGA）对其结构进行表征；采用循环伏安法、恒流充放电和交流阻抗对其电化学性能进行研究. 结果表明：生成的MnO₂均匀地负载在碳的表面，形成多层次结构，并且随着温度的升高IPC表面负载的MnO₂由纳米颗粒变为纳米片状结构；MnO₂纳米片具有典型的K-Birnessite 型晶体结构；复合物中MnO₂的含量约为34%（w）. 在100 ℃制备的IPC/MnO₂复合材料在三电极系统中最高比电容达到了411 F·g^-1；随着反应温度的升高,比容量先增长后基本保持不变. 以IPC/MnO₂为正极，活性炭（AC）为负极，1 mol·L^-1 Na₂SO₄溶液为电解液组装成IPC/MnO₂//AC 混合超级电容器，发现IPC/MnO₂电极的电容器其电位窗口从1 V扩展到1.8 V，容量可达86F·g^-1，且表现出良好的电容特性和大电流放电性能.     

纳米钒铬复合氧化物的溶剂热合成、表征及催化2,6-二氯甲苯氨氧化反应（英文）

甲基芳烃气相氨氧化反应制备对应的芳香腈被认为是丙烯氨氧化制备丙烯腈之后化工领域又一重大进展,芳香腈是重要的精细化学品,广泛应用于医药、农药、颜料、染料、橡胶、光电材料等领域.其中2,6-二氯甲苯氨氧化反应制备2,6-二氯苯腈是特别重要的反应,2,6-二氯苯腈工业上可用于制备高效除草剂、杀菌剂及各种特种工程塑料;然而相较于其它的甲基芳烃,2,6-二氯甲苯由于甲基邻位有两个较大位阻且较强吸电子的氯原子影响,甲基活性较低,较难发生氨氧化反应,原料转化率和产品收率均较低.本课题组一直致力于发展高活性和选择性的氨氧化催化剂以及有效的策略实现甲基芳烃高效转化为芳香腈,我们曾以硅胶负载的钒磷氧化物(VPO/SiO_2)和钒铬氧化物(VCrO/SiO_2)为催化剂,成功实现了2,6-二氯甲苯氨氧化反应制备2,6-二氯苯腈.钒铬复合氧化物(VCrO)具有广泛的应用,可用于多相催化、气体传感、能量储存等领域.VCrO通常通过高温固相反应制备,然而一般得到的是混合相,产品形态和颗粒大小也不能很好控制;当用于氧化或氨氧化反应时,需要较高的反应温度,原料也容易发生过度氧化,导致积碳及活性降低.我们以V_2O_5和CrO_3为原料,在醇或者醇水溶液中于180℃进行溶剂热反应制备了无定形的VCrO前驱体,然后将前驱体在不同温度下氮气气氛中煅烧,产品通过粉末X射线衍射、透射电镜和X射线光电子能谱等进行表征.当以甲醇或甲醇水溶液为溶剂热反应介质,并且前驱体700℃进行煅烧后,产品为纯的正交晶系CrVO4纳米晶相;当以甲醇为溶剂时,CrVO_4晶相的尺寸大约为500 nm;而改为甲醇水溶液为溶剂时,产品尺寸急剧减小到50 nm以下,而且通过改变甲醇和水的体积比分别为10:1,5:1,1:1和1:5时,CrVO_4纳米晶相的尺寸从50 nm逐渐减小到30,20和10 nm,能够进行有效调控.据我们所知,这是首次合成纯的CrVO_4纳米晶相.我们以该纳米CrVO4为催化剂催化2,6-二氯甲苯氨氧化反应制备2,6-二氯苯腈,在335℃的相对较低温度下反应,原料转化率为84%,产品收率为75%;进一步升高温度到390℃,原料转化率为99%,产品收率可达81%.在所有已报道的二元复合氧化物催化剂中,纳米CrVO_4显示了最高的催化活性,主要归功于它较小的粒子尺寸、较大的表面积和更多暴露的活性中心     

复合分子筛催化微晶纤维素水解

采用水热晶化法制备了HY/ZSM-5复合分子筛。通过XRD、SEM、N2-吸附脱附、NH3-TPD及吡啶吸附红外光谱等手段表征催化剂的结构和性质。结果表明,HY与HZSM-5复合后HY型分子筛完全被HZSM-5紧密包裹,形成致密的核壳结构。与机械混合物相比,复合分子筛微孔比表面积及孔体积均有所减少,总酸量略高,弱酸量小,而强酸量大,Br9nsted酸量与之相似,而Lewis酸量有所减少。将所制备的HY/ZSM-5复合分子筛催化剂应用于以离子液体氯化1-乙基-3-甲基咪唑鎓([Emim]Cl)为溶剂的纤维素水解反应中,与HY催化的纤维素水解相比,HY/ZSM-5催化纤维素水解反应获得的最佳葡萄糖收率由28.04%提高到38.78%,葡萄糖选择性由28.91%提高至48.29%。     

Fukui Functions for the Temporary Anion Resonance States of Be~-, Mg~-, and Ca~-

In this work,the Fukui functions of the two ~2P resonance states of Be,a ~2P resonance state of Mg~–,and a ~2D resonance state of Ca~– have been determined.The trajectories of these resonance states,in conjunction with the complex rotation of the Hamiltonian,were used to determine their wave functions.The electron densities,Fukui functions,and values of the hyper-radiusr~2were computed from these wave functions.The Fukui functions have negative regions in the valence shell in addition to the inner shell regions,indicating screening effects of the outer temporary electron.Selected configuration interactions with up to quadruple excitations were used along the trajectories and for computing the final wave function.Based on this data,the densities,Fukui functions,andr~2were calculated.     

Electric and dielectric behavior of copper-chromium layered double hydroxide intercalated with dodecyl sulfate anions using impedance spectroscopy

The Cu₂Cr-DS-LDH hybrid was successfully prepared by the anion exchange method at room temperature. The structure, the chemical composition and the physico-chemical properties of the sample were determined using powder X-ray diffraction (PXRD), Fourier transform infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA) and inductively coupled plasma (ICP). In this work, the electrical and dielectric properties investigated are determined using impedance spectroscopy (IS) in a frequency range of 1 Hz to 1 MHz. Indeed, the Nyquist diagram modelized by an electrical equivalent circuit showed three contributions attributed respectively to the polarization of grains, grains boundaries and interface electrode-sample. This modelization allowed us to determine the intrinsic electrical parameters of the hybrid (resistance, pseudo-capacitance and relaxation time). The presence of the non-Debye relaxation phenomena was confirmed by the frequency analysis of impedance. Moreover, the evolution of the alternating current conductivity (σ_ac) studied obeys the double power law of Jonscher. The ionic conduction of this material was generated through a jump movement by translation of the charge carriers. As for the dielectric behavior of the material, the evolution of dielectric constant as a function of frequency shows relatively high values in a frequency range between 10 Hz and 1 KHz. The low values of the loss tangent obtained in this frequency zone can valorize this LDH hybrid.     

Network synchronization under distributed delayed impulsive control: Average delayed impulsive weight approach

This paper mainly investigates synchronization of complex dynamical networks (CDNs) with both system delay and coupled delay through distributed delayed impulsive control. Instead of constraining the impulsive weight and impulsive delay one by one, a new concept of average delayed impulsive weight is proposed to obtain more relaxed conditions. Subsequently, based on the impulsive control topology, Lyapunov theory and linear matrix inequality (LMI) design, certain flexible criteria of global exponential synchronization (GES) are given and the corresponding convergence rate is estimated. It is interesting to see that the CDNs can still achieve synchronization under comprehensive conditions though impulsive weights work negatively. Namely, the delays in impulsive control are able to promote synchronization potentially. Finally, simulations are given to show that the distributed delayed impulsive control can not only speeds up the convergence rate for synchronized networks, but also facilitates synchronization for desynchronized networks. In addition, the obtained results can be applied to unmanned craft systems.