矿渣粉加固粉土的理论分析及路用性能研究

提出了矿渣粉加固粉土的相关理论。将矿渣粉在加固土中的作用归结为火山灰胶凝效应和微集料填充效应,而火山灰胶凝效应又可进一步归结为水化作用、激发作用和离子交换作用;认为微集料填充效应与矿渣粉细度极为相关;用框图归纳了矿渣粉加固土的两种作用效应。进行了矿渣粉、石灰粉加固土无侧限饱水抗压强度、水稳定性、冻稳定性、温度收缩和干燥收缩等路用性能试验,并进行比较。结果表明,矿渣粉加固土所测路用性能指标优于石灰粉加固土。为工程应用提供了试验依据。     

用于同步辐射光源的成像板粉末衍射系统

报道了我们研制的一套成像板粉末衍射装置,对其误差来源进行了详细的分析讨论,并与衍射仪进行了比较.该装置的半径为143.3mm,最大测量角度范围不160°，最大角度(2q )偏差小于0.03°,这些性能指标已被实验所证实,完全可应用于粉末衍射全谱的测量.     

Flame Temperature Effect on the Structure of SiC Nanoparticles Grown by Laser Pyrolysis

Small SiC nanoparticles (10 nm diameter) have been grown in a flow reactor by CO₂ laser pyrolysis from a C₂H₂ and SiH₄ mixture. The laser radiation is strongly absorbed by SiH₄ vibration. The energy is transferred to the reactive medium and leads to the dissociation of molecules and the subsequent growth of the nanoparticles. The reaction happens with a flame. The purpose of the experiments reported in this paper is to limit the size of the growing particles to the nanometric scale for which specific properties are expected to appear. Therefore the effects of experimental parameters on the structure and chemical composition of nanoparticles have been investigated. For a given reactive mixture and gas velocity, the flame temperature is governed by the laser power. In this study, the temperature was varied from 875°C to 1100°C. The chemical analysis of the products indicate that their composition is a function of the temperature. For the same C/Si atomic ratio in the gaseous phase, the C/Si ratio in the powder increases from 0.7 at 875°C up to 1.02 at 1100°C, indicating a growth mechanism limited by C₂H₂ dissociation. As expected, X-ray diffraction has shown an improved crystallisation with increasing temperature. Transmission electron microscopy observations have revealed the formation of 10 nm grains for all values of laser power (or flame temperature). These grains appear amorphous at low temperature, whereas they contain an increasing number of nanocrystals (2 nm diameter) when the temperature increases. These results pave the way to a better control of the structure and chemical composition of laser synthesised SiC nanoparticles in the 10 nm range.     

Strong visible PL from the nc-Si thin film by Ni silicide mediated crystallization

We studied the growth of nanocrystalline silicon (nc-Si) thin film exhibiting a strong room temperature photoluminescence (PL) at 1.81–2.003 eV. The amorphous silicon was crystallized by Ni silicide mediated crystallization (Ni SMC) and then Secco-etched to exhibit the PL. The PL peak energy and intensity increase with increasing the metal density on the a-Si because of the reduction in the grain size down to 2 nm. The photoluminescence energy and peak intensity depend strongly on the Secco etch time because the grain size is reduced by etching the grain boundaries.     

Self-organized amorphous material in silicon (0 0 1) by focused ion beam (FIB) system

A method using a focused ion beam (FIB) to prepare a silicon amorphous material is presented. The method involves the redeposition of sputtered material generated during the interaction of the Ga⁺ ion beam with a silicon substrate material. The shape and dimensions of this amorphous material are self-organized and reproducible. The stability of this amorphous material under electron irradiation was investigated in the transmission electron microscopy (TEM). Electron irradiation can induce recrystallization of the amorphous material, resulting in the lateral and vertical growth, starting at an amorphous-crystalline interface, of polysilicon containing defects.     

Hydroxyapatite coating on porous silicon substrate obtained by precipitation process

Hydroxyapatite Ca₁₀(PO₄)₆(OH)₂ (HAP) is known as a bioactive and biocompatible material, HAP coatings were used to improve the biocompatible of substrate by many researcher, In this work, HAP thin films on porous silicon (PS) substrates have been prepared by aqueous precipitation method with rapid thermal annealing (RTA) processes. The HAP films had been prepared under the annealing temperature ranging from 300 to 1000 °C. By the measurement of X-ray diffraction (XRD), it was found that for the crystallinity optimization, the heat-treatment at 850–950 °C for 1 h would be favorable. Atomic force microscopy (AFM) and scanning electron microscope (SEM) measurements reveal a dense and smooth surface of the HAP film, and tightly adherence of the coating on porous silicon substrate after sintered. Thus, by this method, porous silicon could be increased its bioactivity and so that could be used in the biomedical area.     

TiO2 粉末催化剂光催化降解室内 空气中有机污染物

本文制备了一系列 TiO2粉末催化剂, 用光催化法降解室内空气中各种微量有机污染物,最终降解率 接近 100%. 考察了晶型对光催化剂性能的影响, 结果表明,锐钛矿型 TiO2 的催化性能最好. 最后,分析了 TiO2 光催化反应机理.     

Rebuilding of metal components with laser cladding forming

Laser cladding forming (LCF) is a novel powerful tool for the repairing of metal components. Rebuilding of V-grooves on medium carbon steel substrates has been carried out with laser cladding forming technique using stainless steel powder as the cladding material. Microstructure of the deposited layers has been characterized using optical microscopy (OM), scanning electron microscopy (SEM), energy dispersive X-ray microanalysis (EDAX), electron probe microanalysis (EPMA) and X-ray diffraction (XRD). Mechanical properties of the rebuilt V-groove samples have been evaluated by tensile and impacting tests and microhardness measurement. Experimental results show that good fusion bonding between the rebuilt layers and the substrate has been formed, and the microstructure of the cladding layers is mainly composed of fine, dense and defect-free epitaxial columnar dendrites. Due to the effect of grain size refinement, the tensile strength, impacting toughness, elongation and microhardness of the rebuilt samples have been greatly enhanced compared to those of the substrate. Microhardness is also very uniform throughout the rebuilt regions. With the growth of the deposited layers, the microhardness increases gradually. The good ductility of the deposited regions is verified by the SEM fracture analysis.     

The effect of oxidation on physical properties of porous silicon layers for optical applications

In order to understand the optical loss mechanisms in porous silicon based waveguides, structural and optical studies have been performed. Scanning and transmission electron microscopic observations of porous silicon layers are obtained before and after an oxidation process at high temperature in wet O₂. Pore size and shape of heavily p-type doped Si wafers are estimated and correlated to the optical properties of the material before and after oxidation. The refractive index was measured and compared to that determined by the Bruggeman model.