导电复合材料葡萄糖氧化酶传感器的研究

报导了用乙基纤维素和乙炔黑获得的导电复合材料构成的葡萄糖氧化酶生物传感器的制备方法.讨论了多种因素对该生物传感器响应电流的影响.测得此电极酶催化反应的活化能为40.3 kJ•mol－1. AFM实验表明，用环己烷洗去石蜡的导电复合材料 葡萄糖氧化酶生物传感器具有粒状结构，这有利于酶催化反应的进行.     

光化学-荧光分析法研究——Ⅲ.片剂及注射液中安定的测定

本文提出了测定安定的光化学—荧光分析新方法。安定在含有十二烷基硫酸钠的稀硫酸介质中,经紫外光照射后,产物能发射荧光(=368nm,=476nm)。安定浓度在0～2.5μg/ml范围内,荧光强度与浓度成良好的线性关系。方法的相对标准偏差为1.5％,检出限为0.044μg/ml,可用于片剂及注射液中安定含量的测定。     

LaC_3~n(n=-1,0,+1)分子簇的理论研究(英文)

用密度泛函方法研究了ＬａＣ３ｎ（ｎ＝－１，０，＋１）分子簇的结构和稳定性，对这个四原子体系，提出了５种可能构型，其中３种具有Ｃ２ｖ对称性，２种为Ｃ∞ｖ对称性．在Ｃ２ｖ对称性结构中，其中１个为Ｌａ接在弯曲的Ｃ３链上，第２个是Ｌａ通过２个键与Ｃ３环相链，第３个是Ｌａ通过１个键与Ｃ３环相连；在Ｃ∞ｖ对称性中，第１个Ｌａ接在Ｃ３链的一端，而在第２个构型中，Ｌａ被插入在Ｃ３链中．结果表明，环状结构当Ｌａ接在弯曲的Ｃ３链上的是局域极小值并且最稳定     

水热法制备高纯超细CeO2-ZrO2复合氧化物

Superfine composite powders of CeO₂-ZrO₂ (CZ) and CeO₂-ZrO₂-La₂O₃ (CZL) were prepared by hydrothermal method. The effects of pH、temperature and time for hydrothermal process on the performance of the resulting powders were studied. The optimized reaction parameters were on follows: the precursor′s pH≈9.0, hydrothermal temperature of 200 ℃ holding for 2 h. Thermal stable powders with average particle size smaller than 10 nm and specific surface area of 171 m²·g^-1 were obtained. A BET specific surface area was still at 44 m²·g^-1 after calcination at 1 000 ℃ for 6 hours.     

双波长K系数—标准加入吸光光度法同时测定锰和锌

研究应用双波长K系数—标准加入吸光光度法同时测定锰和锌二组分混合物.试验确定了锰和锌测定中K_(Mn)与K_(Zn)的回归方程.对合成试样、人发试样测定,结果满意.     

铜中杂质成分标准物质的研制

介绍铜中9种杂质成分标准物质的研制方法。以1号纯铜为基体，配入硫、铁、铅、锌、镍、铋、锑、磷、砷及锡共10种杂质成分，采用雾化喷粉加工工艺，保证了样品的均匀性。对样品表面作了抗氧化保护处理。采取多家实验室协作定值的方式对除砷外的9种杂质成分进行定值。5年的跟踪检验结果表明，该标准物质稳定性良好。     

Synthesis and Luminescence Property of 4,4＇-Bis（2,2-di（4-fluorophenyl）vinyl）biphenyl for Organic Blue-Light-Emitting Diodes

The novel fluorinated distyrylarylene, 4,4＇-bis（2,2-di（4-fluorophenyl）vinyl）biphenyl （DFPVBi）, was synthesized and fully characterized. The structure was confirmed with IR, 1↑H NMR, 13↑C NMR, 19↑F NMR and MS analyses. Its electronic and photoluminescence properties were investigated by UV-Vis absorption, cyclic voltammetry and fluorescence spectroscopy. The energy levels of the highest occupied molecular orbital （HOMO） and the lowest unoccupied molecular orbital （LUMO） are --5.77 and --2.75 eV, respectively. The electroluminescence proper- ties of the organic light-emitting diode fabricated by DFPVBi were also studied. The device exhibits a pure blue emission peaked at 454 nm, which indicates a maximum luminance of 5872 cd/m ^2 at 14.2 V and a maximum current efficiency of 2.82 cd/A at 10V, respectively.     

Analysis of thermal behaviour of high power semiconductor laser arrays by means of the finite element method (FEM)

New results of steady-state two-dimensional finite-element computations of temperature distributions of high power semiconductor laser arrays are presented. The influence of different thermal loads on the 2D temperature distribution in AlGaAs/GaAs gain-guided laser arrays is investigated. TheFEM model is tested by comparing it with analytical solutions. For numerical convenience, the latter is rewritten in a novel form, which is free of overflow problems. The maximum temperatures calculated by both methods agree within 1%. Several factors determining the thermal resistance of the device are quantitatively examined: the ratio of light emitting to non-emitting areas along the active zone, the amount of Joule losses, the current spreading, the solder thickness, and voids in the solder. This yields design rules for optimum thermal performance.     

Non-stoichiometry of YBa2Cu3O7-d Observed by Repeated Temperature Scanning

Repeated temperature scanning method was applied to observe non-stoichiometry of YBa₂Cu₃O₇-d, and interesting results were obtained. Two simultaneously occurring processes were separately observed in mass change; one is a fast process and the other is slow, so that their responses to the temperature change are quite different from each other. The fast process follows the cyclic temperature change, but the slow process is observed to be a gradual mass change. Kinetic behaviors of these two processes are also made clear by plotting the mass vs. the temperature. Furthermore, a hysteresis loop was observed in the plot of the mass vs. the temperature in a high temperature range presumably due to the third process, and it depends on the heating and cooling rates. This revised version was published online in July 2006 with corrections to the Cover Date.     

Dynamic headspace liquid-phase microextraction of alcohols

A method was developed using dynamic headspace liquid-phase microextraction and gas chromatography-mass spectrometry for extraction and determination of 9 alcohols from water samples. Four different solvents, hexyl acetate, n-octanol, o-xylene and n-decane were studied as extractants. The analytes were extracted using 0.8 microl of n-octanol from the headspace of a 2 ml sample solution. The effect of sampling volume, solvent volume, sample temperature, syringe plunger withdrawal rate and ionic strength of the solution on the extraction performance were studied. A semiautomated system including a variable speed stirring motor was used to ensure a uniform movement of syringe plunger through the barrel. The method provided a fairly good precision for all compounds (5.5-9.3%), except methanol (16.4%). Detection limits were found to be between 1 and 97 microg/l within an extraction time of approximately 9.5 min under GC-MS in full scan mode.