Measurement of micro weld joint position based on magneto-optical imaging

In a laser butt joint welding process,it is required that the laser beam focus should be controlled to follow the weld joint path accurately.Small focus wandering off the weld joint may result in insufficient penetration or unacceptable welds.Recognition of joint position offset,which describes the deviation between the laser beam focus and the weld joint,is important for adjusting the laser beam focus and obtaining high quality welds.A new method based on the magneto-optical(MO)imaging is applied to measure the micro weld joint whose gap is less than 0.2 mm.The weldments are excited by an external magnetic field,and an MO sensor based on principle of Faraday magneto effect is used to capture the weld joint images.A sequence of MO images which are tested under different magnetic field intensities and different weld joint widths are acquired.By analyzing the MO image characteristics and extracting the weld joint features,the influence of magnetic field intensity and weld joint width on the MO images and detection of weld joint position is observed and summarized.     

GC–MS with photoionization of cold molecules in supersonic molecular beams—Approaching the softest ionization method

A new type of photoionization ion source was developed for the ionization of cold molecules in supersonic molecular beams (named Cold PI). The system was based on a GC–MS with supersonic molecular beams and its fly‐through EI of cold molecules ion source (Cold EI) plus quadrupole mass analyzer. A continuously operated deuterium VUV photoionization lamp was added and placed above and between the supersonic nozzle and skimmer whereas the Cold EI ion source served only as a portion of the ion transfer ion optics. The supersonic nozzle and skimmer were voltage biased and the VUV light crossed the supersonic expansion about 10 mm from the nozzle. We obtained over three orders of magnitude enhancement in the relative abundance of the molecular ion of squalane in Cold PI versus in photoionization of this compound as a thermal compound. Accordingly, we also proved that standard photoionization is not as soft ionization method as previously perceived for large compounds. We found that Cold PI is as soft as and possibly softer than field ionization; thus, it could be the softest known ionization method. The ionization yield was about 200–300 times weaker than with Cold EI yet our limit of detection was about 200 femtogram in SIM mode for cholesterol and pyrene which is reasonable. Practically, all hydrocarbons gave only molecular ions with rather uniform response whereas alcohols gave some molecular ions plus major fragment ions particularly with a loss of water (similarly to field ionization). We tested Cold PI in the GC–MS analysis of diesel fuels and analyzed the time averaged data for group type information. We also found that we can analyze the diesel fuels by fast under 20‐s flow injection analysis in which the generated averaged mass spectrum of molecular ions only could serve for the characterization of fuels.     

Analysis of impurities in pharmaceuticals by LC‐MS with cold electron ionization

Pharmaceuticals require careful and precise determination of their impurities that might harm the user upon consumption. Although today, the most common technique for impurities identification is liquid chromatography‐mass spectrometry (LC‐MS/MS), it has several downsides due to the nature of the ionization method. Also, the analyses in many cases are targeted thus despite being present, some of the compounds will not be revealed. In this paper, we propose and show a new method for untargeted analysis and identification of impurities in active pharmaceutical ingredients (APIs). The instrument used for these analyses is a novel electron ionization (EI) LC‐MS with supersonic molecular beams (SMB). The EI‐LC‐MS‐SMB was implemented for analyses of several drug samples spiked with an impurity. The instrument provides EI mass spectra with enhanced molecular ions, named Cold EI, which increases the identification probabilities when the compound is identified with the aid of an EI library like National Institute of Standards and Technology (NIST). We analyzed ibuprofen and its impurities, and both the API and the expected impurity were identified with names and structures by the NIST library. Moreover, other unexpected impurities were found and identified proving the ability of the EI‐LC‐MS‐SMB system for truly untargeted analysis. The results show a broad dynamic range of four orders of magnitude at the same run with a signal‐to‐noise ratio of over 10 000 for the API and almost uniform response.     

宽幅钢箱梁环焊缝焊接顺序优化研究

基于热弹塑性有限元法,采用ANSYS软件建立了网格疏密过渡的单箱五室钢箱梁壳单元模型;结合高效的分段移动热源,实现了对大型复杂长焊缝结构焊接全过程的数值模拟,并定性对比了宽幅钢箱梁在不同的环焊缝焊接顺序下顶板和底板的变形情况.分析结果表明:腹板焊缝的焊接顺序对竖向最大变形值(绝对值)的影响不大,其值主要取决于顶板和底板...     

Bose-like few-fermion systems

It is shown that the specific heat of a few-fermion system with odd number fermions behaves differently from that of a few-fermion system with even number fermions. The specific heat of an even-number-fermion system behaves like a Bose one rather than a Fermi one.     

THERMOTROPIC LIQUID CRYSTALLINE COPOLYESTERS-SOLID STATE POLYMORPHISM

This paper offers some new evidence on the polymorphism of solid state of liquid crystalline aromatic copolyesters which were prepared in our laboratory. The effects of different treatment conditions(quenching and annealing) on solid structure have been examined mainly by DSC and X-ray diffraction. The discussion focuses on the supercooled mesophase and low temperature solid-solid transition, the shifting of double melting peaks of annealed samples and the changing of their ΔH data depending on the treatment temperature, time and thermal scanning rate.     

冷原子吸收光谱法测定磷酸二氢钾中的汞

用冷原子吸收光谱法测定磷酸二氢钾中的汞含量,研究了测定介质及其浓度、重铬酸钾用量、还原剂用量、共存元素干扰等因素对测定的影响,在本试验条件下方法的回收率为97%-104%,相对标准偏差＜10%.     

Laser welding of thin foil nickel-titanium shape memory alloy

In this study, two L27 Taguchi experiments were carried out to study the effect of fibre laser welding parameters and their interactions upon the weld bead aspect ratio of nickel-titanium thin foil. The optimum parameters to produce full penetrated weld with the largest aspect ratio and desirable microstructure were successfully obtained by the Taguchi experimental design. The corrosion property of the optimized NiTi weld in Hank’s solution at 37.5 °C was studied and compared with the as-received NiTi. To improve the corrosion properties of the weld, the effect of post-weld-heat-treatments ranging from 573 to 1173 K was investigated. The corrosion properties, surface morphology, microstructure and Ti/Ni ratio of the heat-treated NiTi weld were analysed. It was found that a post-weld heat treatment at 573 K for 1 h provided the best pitting corrosion resistance at the weld zone.     

共价氢化物与汞离子反应的研究：Ⅱ.痕量硒的高灵敏分析新方法

本文详细研究了硒化氢与汞离子反应条件并建立了氢化物发生－冷原子荧光法间接测定痕量硒的新方法。考察了各种实验条件，并将此方法用于合成水样分析，得到一些有意义的结果。     

CO2 laser welding of copper slabs

For the first time it has been possible to laser weld copper sheets up to 3 mm thick with a 2 kW cw CO₂ laser. The main questions arising from the process are indicated.