Electromagnetic interference shielding and radiation absorption in thin polypyrrole films

Results of permittivity measurements, electromagnetic interference shielding effectiveness, and heat generation due to microwave absorption in conducting polymer coated textiles are reported and discussed. The intrinsically conducting polymer, polypyrrole, doped with anthraquinone-2-sulfonic acid (AQSA) or para-toluene-2-sulfonic acid (pTSA) was applied on textile substrates and the resulting materials were investigated in the frequency range 1-18 GHz. The 0.54 mm thick conducting textile/polypyrrole composites absorbed up to 49.5% of the incident 30-35 W microwave radiation. A thermography station was used to monitor the temperature of these composites during the irradiation process, where absorption was confirmed via visible heat losses. Samples with lower conductivity showed larger temperature increases caused by microwave absorption compared to samples with higher conductivity. A sample with an average sheet resistivity of 150 Ω/sq. showed a maximum temperature increase of 5.27 °C, whilst a sample with a lower resistivity (105 Ω/sq.) rose by 3.85 °C.     

Hydrogen bonded layer-by-layer assembly of poly(2-vinylpyridine) and poly(acrylic acid): Influence of molecular weight on the formation of microporous film by post-base treatment

This article describes the buildup of hydrogen bonded multilayer film of poly(2-vinylpyridine) (P2VP) and poly(acrylic acid) (PAA), and the influence of polymer molecular weight on the formation of microporous film by post-base treatment. The formation of a microporous film involved a two-step mechanism: the release of PAA from P2VP/PAA multilayer, and the reorganization of the remaining P2VP on the substrate. Fourier transform infrared spectroscopy (FT-IR) indicated that the release of PAA from hydrogen bonded multilayer was a rapid process, which was almost independent of the molecular weight of PAA. Furthermore, the molecular weight of P2VP had a great effect on micropore formation by immersing the P2VP/PAA multilayer in basic solution. The rate of micropore formation increased with increasing molecular weight. We anticipate that a comparative study on P2VP/PAA films containing high or low molecular weight polymer provides a way to control the surface morphology, and will be helpful and constructive for the forthcoming discussion about the formation of the microporous film.     

Reactivity in the solid state between CoWO4 and RE2WO6 where RE = Sm, Eu, Gd

Reactivity in the solid state between CoWO₄ and some rare-earth metal tungstates RE₂WO₆ (RE = Sm, Eu, Gd) was investigated by the XRD method. Two families of new isostructural cobalt and rare-earth metal tungstates, Co₂RE₂W₃O₁₄ and CoRE₄W₃O₁₆, were synthesized. The Co₂RE₂W₃O₁₄ phases are formed by heating in air the CoWO₄ and RE₂WO₆ compounds mixed at the molar ratio 2:1, while the CoRE₄W₃O₁₆ phases are synthesized at the molar ratio of CoWO₄/RE₂WO₆ equals to 1:2. The Co₂RE₂W₃O₁₄ phases as well as the CoRE₄W₃O₁₆ compounds crystallize in the orthorhombic system. The Co₂RE₂W₃O₁₄ and CoRE₄W₃O₁₆ compound melt above 1150 °C. A melting manner of the Co₂RE₂W₃O₁₄ and CoRE₄W₃O₁₆ compounds was determined in an inert atmosphere. The formation of CoWO_4−x phase was observed during heating in an inert atmosphere.     

Electron microscopic phase analysis of BN-thin films

A series of BN films was deposited by means of r.f. magnetron sputtering of a h-BN target onto Si(1OO) surfaces. Hereby, the substrate bias voltage was varied. Special interest is focussed to the influence of the deposition parameters on the orientation of the growing hexagonal BN film with respect to the substrate. For structural investigation, cross section samples were prepared. In addition to HRTEM and diffraction investigations, especially electron energy loss spectroscopy (EELS) was applied successfully for phase identification. For negative bias voltages of U _B =–300 V and U _B =–350V, we found a phase system consisting of a first-grown 25 nm thick layer of hexagonal structure with the c axis parallel to the substrate surface followed by the cubic phase.Dedicated to Professor Dr. rer. nat. Dr. h.c. Hubertus Nickel on the occasion of his 65th birthday     

Sol–gel preparation and properties of hydroxypropylcellulose–titania hybrid thin films

Hydroxypropylcellulose (HPC)–titania hybrid thin films were prepared by sol–gel method where titanium tetraisopropoxide Ti(OC₃H₇ ⁱ )₄ was hydrolyzed under acidic conditions in the presence of HPC, followed by dip-coating and drying at 120 °C for 24 h. The viscosity average molecular weight of HPC was 55,000–70,000 or 110,000–150,000, and the TiO₂/(HPC + TiO₂) mass ratio ranged from 0 to 1, which was calculated on the assumption that all Ti(OC₃H₇ ⁱ )₄ is converted into TiO₂. The films were 0.35–1.0 μm thick, transparent in visible region and opaque in ultraviolet (UV) region, where the optical absorption coefficient in UV region increased with increasing titania content. The refractive index increased with increasing titania content, ranging from 1.6 to 1.8 for the hybrid thin films. The pencil hardness increased from 6B to 5H, the durability in hot water significantly increased and the contact angle of water on films increased from 35° to 89° with increasing titania content. Crack-free films could be deposited on organic polymer substrates irrespective of titania or HPC contents, where cracking did not occur at higher HPC contents even when the substrate was bent.     

Influence of the cathodic polarization on the stability of Ti surface in concentrated KOH solutions

The stability of spontaneous thin layers and thin layers formed upon cathodical polarization of Ti in KOH solutions have been studied by potentiostatic and ellipsometric methods. At open circuit potential (OCP) the strongly adherent films, whose thickness depends on the concentration of the KOH solution, were formed. During the cathodic polarization the transformation of these films to weakly adsorbed precipitated layers on the electrode surface was observed. Comparing the theoretically computed curves with the experimental Ψ vs Δ loci measured ellipsometrically, the complex indices of refraction and the thickness of the generated films, from 3.6 to 60 nm in 1 M KOH and from 36 to 105 nm in 5 M KOH (adherent to the electrode surface), were determined. At OCP the rate of film growth increases with increasing the concentration of KOH solution. Cathodic polarizations change the chemical composition and retard the rate of film growth. Based on the ellipsometric and electrochemical data the chemical compositions of the formed films consisted of TiO₂, Ti₂O₃, TiO₂·H₂O, Ti(OH)₃ and TiOOH·nH₂O.     

A surface adsorption model for electroless cobalt alloy thin films

Thin cobalt alloy films have been obtained using electroless deposition solution with two reducing agents: dimethylamine borane (DMAB) and sodium hypophosphite. This system allows spontaneous and self-activated deposition of barrier layers on Cu lines and via contacts for ultra large scale integration (ULSI) interconnects applications. This work presents a study of the solution composition effects on the material properties and composition of the films. First, we present the deposition rates, the electrical resistance, the various element profiles in the thin film, and the thin film roughness. Next, we discuss the film’s composition and its dependence on the ratio between the reducing agents composition in the solution. The experimental results suggest that the film phosphorous and boron composition is determined by the surface adsorption rates of the reducing agents. Therefore, a surface co-adsorption model of the two reducing agents is proposed, formulated, analyzed, and compared to the experimental results. Finally, we discuss the model and its significance to the formation of high-quality ultra-thin barrier layers. Dedicated to Professor Dr. Algirdas Vaskelis on the occasion of his 70th birthday.     

Heterometallic lead-titanium oxyalkoxide precursors to lead titanate thin films

Two lead titanium oxyalkoxides with composition Pb₂Ti₄O₂(O₂CCH₃)₂(OC₂H₅)₁₄ and Pb₂Ti₂O₂(O₂CCH₃)₂(OCH(CH₃)₂)₈ have been isolated and characterised by elemental analysis, IR, ²⁰⁷Pb NMR and molecular weight measurements. X-ray structural analysis of the 1:2 complex confirmed the presence of two Pb₂Ti₂O units which are linked by a common Pb···Pb edge and are held together by alkoxide and acetate bridges. The acetate groups have migrated from the Pb to the Ti centres during the reaction. Hydrolysis of the 1:1 Pb/Ti complex produced clear gels providing the H₂O/complex ratio was less than 4. Heat treatment of the gel results in loss of residual organics below 400°C. The XRD pattern indicates the presence of the pyrochlore and perovskite phases after heating at 500°C but the sample is poorly crystalline. Complete conversion to the perovskite phase of lead titanate occurs on heating to 600°C for 1 hour. Thin films of lead titanate were deposited by dip-coating a solution of this complex in isopropanol. Analyses of the films, carried out using electron microprobe, Scanning Auger Spectroscopy and Rutherford Backscattering, indicated that they were of excellent quality, crystalline after heating at 600°C and with relatively sharp substrate-coating interface.     

Linked crystallites in the conducting topmost layer of polymer bilayer films controlled by temperature: from micro- to nanocrystallites.

Temperature has great impact on the structure and size of the linked crystallites of the conducting topmost layer formed at the surface of a polycarbonate film via the reaction BEDT-TTF+IBr [BEDT-TTF=bis(ethylenedithio)tetrathiafulvalene]. We show that fine temperature control permits formation of a semiconducting topmost layer of alpha'-(BEDT-TTF)(2)(I(x)Br(1-x))(3) crystallites with either micro- or nanometre size, a result that opens a route to miniaturized conducting plastic materials.     

Nanocomposite materials from latex and cellulose whiskers

Composite materials were processed by casting a mixture of aqueous suspensions of latex and microfibrils. These microfibrils, or whiskers, are extracted from a sea animal and are monocrystals of cellulose, with an aspect ratio around 100 and an average diameter of 20 nm. It has been found that the mechanical properties (shear modulus) are increased by more than two orders of magnitude in the rubbery state of the polymeric matrix, when the whisker content was 6% (w/w). This very large effect is discussed on the basis of different types of mechanical models and it is concluded that these whiskers form a rigid network, probably linked by hydrogen bonds. The formation of this network is assumed to be governed by a percolation mechanism.