高砷低金银的铅阳极泥中银的冶炼

本文报导了将纯碱加入砷含量高的铅阳极泥熔炼成贵铅，用硝酸溶解，硫氰酸盐沉淀，再用锌粉还原得银的方法。从而避免砒霜挥发。     

Use of the molybdenum-thiocyanate-rhodamine 6G ternary complex for spectrophotometric molybdenum determination without extraction

A modified thiocyanate method without extraction by using rhodamine 6G as a secondary ligand was developed. Molybdenum in 1.0×10⁻² M HCl, after the addition of ascorbic acid, was heated for 10 min in a 90 °C water bath for reduction. Suitable amounts of glycerine, Triton X-100, rhodamine 6G solutions and 2+1 (v/v) 9 M H₂SO₄+3 M KHSO₄ were added in this order. This solution was allowed to cool to room temperature and the absorbance at 570 nm was measured against a reagent blank 45 min after the addition of thiocyanate solution and the second aliquot of Triton X-100 solution. The complex was stable for at least 4 h, the order of reagent addition was important, and thiocyanate should be in large excess. Beer’s law was obeyed over the range 0.9×10⁻⁶ to 1.1×10⁻⁵ M Mo with the molar absorptivity being 1.1×10⁵ l mol⁻¹ cm⁻¹. The R.S.D. for the determination of 0.7 mg Mo l⁻¹ was 1.83% (n=8). Possible interferences of various cations and anions on molybdenum determination were studied. The proposed method was applied to the determination of molybdenum in a dental alloy, Wiron 99.     

离子交换树脂负载Ni—B无定形合金催化剂的制备与性能

制备了一种新型离子交换树脂负载的Ｎｉ－Ｂ无定形合金催化剂．用３种树脂作为催化剂载体，即弱酸型阳离子树脂Ｄ１５２，强酸型阳离子树脂Ｄ７２及强碱型阴离子树脂Ｄ２６１．用ＸＰＳ、ＴＥＭ和ＩＣＰ等技术对催化剂进行了表征．结果表明，催化剂上镍与带有功能基的载体树脂之间有着很强的相互作用，但其强度与所带的功能基有关．３种催化剂Ｎｉ２ｐ３／２的ＸＰＳ谱图上，ＮｉＢ／Ｄ１５２催化剂的氧化态峰最小，而ＮｉＢ／Ｄ２６１的氧化态峰最大．异丙醇脱氢反应活性实验证实了这一结果．     

MoO3/TiO2-Al2O3催化剂表面结构的LRS研究

负载型Mo和Co-Mo催化剂由于工业上的广泛应用,多年来一直是催化工作者的重要研究课题.工业上应用的Mo和Co-Mo催化剂多以活性Al_2O_3和SiO_2-Al_2O_3为载体,近年来也有用TiO_2,ZrO_2和活性碳作为催化剂载体的研究报导.有关催化剂活性组分与载体之间相互作用对催化剂表面相结构和催化性能的影响方面研究已引起人们的重视。我们多年来在金属-载体相互作用研究基础上,以石油加氢精制催化剂为应用背景,开     

Adsorption of n-Butanol from Aqueous Solutions on a Bi–Ga Electrode

Curves of the differential capacitance at the Bi–Ga/H₂O interface in 0.05 M Na₂SO₄ solutions with different concentrations of n-C₄H₉OH are obtained by a bridge method at 420 Hz and 32°C. Adsorption parameters of n-C₄H₉OH, determined by a regression analysis of these curves, are compared with relevant data for mercury and partially fused polycrystalline bismuth (pBi). That the adsorption behavior of organic molecules at Hg differs from that at pBi and Bi–Ga is due not to their different hydrophilicity but to a different physical interaction water–electrode. The reason for this phenomenon can be an unequal spread of electron density beyond the ionic cores of Hg and Bi. These notions are corroborated by the fact that the Bi–Ga data fit overall correlation dependence between the electronic capacitance of different electrodes in the absence of a chemisorption interaction metal–water and the adsorbability of the n-C₄H₉OH molecules on them.     

Characterization of chromate conversion coating on AA7075‐T6 aluminum alloy

Chromate conversion coatings (CCCs) on AA7075‐T6 were characterized using scanning electron microscopy, focused ion beam sectioning and scanning transmission electron microscopy with nano‐electron dispersive spectroscopy line profiling. The thickness and composition of the CCC was different at different locations on the heterogeneous microstructure of AA7075‐T6. The coating formed on the matrix phase was much thicker than that formed on the coarse Al–Cu–Mg, Al–Fe–Cu and Mg–Si intermetallic particles. Nano‐electron dispersive spectroscopy line profiling indicated that the coating on the Al–Fe–Cu particles was similar to the CCC formed on the phase matrix, primarily a chromium oxide. However, the coatings on the Al–Cu–Mg and Mg–Si particles were mixed Al/Mg/Cr oxide and Mg oxide, respectively. The growth of CCC followed a linear‐logarithmic kinetic rate law. The observations of this study support the sol‐gel model of CCC formation. Copyright © 2004 John Wiley & Sons, Ltd.     

Ammonium tetraphenylborate-naphthalene adsorbent for the preconcentration and trace determination of uranium in standard alloys and synthetic samples using 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol by fourth-derivative spectrophotometry

A solid ion-pair material produced from ammonium tetraphenylborate (ATPB) and naphthalene has been used for the preconcentration of uranium from the large volume of its aqueous complex samples. Uranium reacts with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (5-Br-PADAP) to form a water insoluble, coloured complex. This complex is quantitatively retained on the ATPB-naphthalene adsorbent filled in a column in the pH range 7.0–9.5 and at a flow rate of 2 ml/min. The solid mass from the column is dissolved with 5 ml of dimethylformamide (DMF) and uranium is determined by fourth-derivative spectrophotometry. The calibration curve is linear over the concentration range of 0.13–15.0 g of uranium in 5 ml of the final DMF solution. Seven replicate determinations of 6 g of uranium gave a mean peak height (peak-to-peak signal between 592 nm and 582 nm) of 1.02 with a relative standard deviation of 0.95%. The sensitivity is 0.8419 (d⁴A/d⁴)/(g ml^–1) found from the slope of the calibration curve. The interference of a large number of anions and cations on the estimation of uranium has been studied and the method applied for the determination of uranium in coal fly ash, Zr-base alloy and some synthetic samples corresponding to standard alloys.     

Electrical Double Layer on Liquid Sn–Ga Alloy in Aqueous Solutions

Double-layer parameters of a liquid Sn–Ga electrode in aqueous electrolyte solutions are studied. It is shown that Sn in the alloy with Ga is a surface-active component and is forced out onto a surface layer of the electrode. The double-layer parameters of an Sn–Ga electrode (8 at. % Sn), which are measured in the experimentally accessible range of charges, differ radically from the parameters of Ga electrodes and are close to those of Sn electrode. Hence, an Sn–Ga electrode containing 8 at. % Sn simulates electrochemical properties of a liquid Sn electrode. The difference between reciprocal electronic capacitances of Hg and Sn and a corrected electrochemical work function of Sn are determined. It is shown that the chemisorption interaction of an Sn–Ga electrode with water molecules is virtually absent at charges more negative than –7 C/cm². A potential drop on uncharged Sn, which is associated with water chemisorption, is –20 mV. Thus, the hydrophilicity of Sn is slightly higher than that of Hg, Bi–Ga, Pb–Ga, and Tl–Ga and significantly lower than that of In–Ga, Cd–Ga, and Ga.     

A comparative study on the single-scan and multiple-scan techniques in differential scanning calorimetry: Application to the crystallization of the semiconducting Ge0.13Sb0.23Se0.64 alloy

A method has been developed for analysing the evolution with time of the volume fraction transformed and for calculating the kinetic parameters at non-isothermal reactions in materials involving formation and growth of nuclei. By considering the assumptions of extended volume and random nucleation, a general expression of the fraction transformed as a function of time has been obtained in isothermal crystallization processes. Considering the mutual interference of regions growing from separate nuclei the Johnson–Mehl–Avrami equation has been deduced as a particular case. The application of the transformation rate equation to the non-isothermal processes has been carried out under the restriction of a nucleation which takes place early in the transformation and the nucleation frequency is zero thereafter. Under these conditions, the kinetic parameters have been deduced by using the techniques of data analysis of single-scan and multiple-scan. The theoretical method developed has been applied to the glass-crystal transformation kinetics of the semiconducting Ge_0.13Sb_0.23Se_0.64 alloy. The kinetic parameters obtained according to both techniques differ by only about 2.5%, which confirms the reliability and accuracy of the single-scan technique when calculating the above-mentioned parameters in non-isothermal transformation processes. The phases at which the above-mentioned semiconducting glass crystallizes after the thermal process have been identified by X-ray diffraction. The diffractogram of the transformed material shows that microcrystallites of Sb₂Se₃ and GeSe are associated with the crystallization process, remaining a residual amorphous matrix.     

Electrocatalysis of Nitrate Reduction at Copper‐Nickel Alloy Electrodes in Acidic Media

The cathodic reduction of NO in 1.0 M HClO₄ is investigated by voltammetry at pure Ni and Cu electrodes, and three Cu‐Ni alloy electrodes of varying composition, all configured as rotated disks. Voltammetric data obtained using these hydrodynamic electrodes demonstrate significantly improved activity for NO reduction at Cu‐Ni alloy electrodes as compared to the pure Ni and Cu electrodes. This observation is explained on the basis of the synergistic benefit of different surface sites for adsorption of H‐atoms, generated by cathodic discharge of H⁺ at Ni‐sites, and adsorption of NO at Cu‐sites on these binary alloy electrodes. Koutecky‐Levich plots indicate that the cathodic response for NO at a Cu₇₅Ni₂₅ electrode corresponds to an 8‐electron reduction, which is consistent with production of NH₃. In comparison, the cathodic response at Cu₅₀Ni₅₀ and Cu₂₅Ni₇₅ electrodes corresponds to a 6‐electron reduction, which is consistent with production of NH₂OH. Flow injection data obtained using Cu₅₀Ni₅₀ and Cu₂₅Ni₇₅ electrodes with 100‐μL injections exhibit detection limits for NO of ca. 0.95 μM (ca. 95 pmol) and 0.60 μM (ca. 60 pmol), respectively.