Influence of SiO2 in SiCp on the microstructure and impact strength of Al/SiCp composites fabricated by pressureless infiltration

The effect of SiO₂ in SiC_p and the following processing parameters on the microstructure and impact strength of Al/SiC_p composites fabricated by pressureless infiltration was investigated: Mg content in the aluminum alloy, SiC particle size, and holding time. Preforms of SiC_p in the form of rectangular bars (10 × 1 × 1 cm) were infiltrated at 1150°C in an argon→nitrogen atmosphere for 45 and 60 min by utilizing two aluminum alloys (Al-6 Mg-11 Si and Al-9 Mg-11 Si, wt.%). The results obtained show that the presence of SiO₂ in SiC affects the microstructure and impact strength of the composites significantly. When Al₄C₃ is formed, the impact strength decreases. However, a high proportion of SiC to SiO₂ limits the formation of the unwanted Al₄C₃ phase in the composites. Also, a higher content of Mg in the Al alloy lowers the residual porosity and, consequently, increases the composite strength. The impact strength grows with decrease in SiC particle size and increases considerably when the residual porosity is less than 1%. Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 42, No. 3, pp. 401–418, May–June, 2006.     

High temperature annealing effect on structural and magnetic properties of Ti/Ni multilayers

High temperature annealing effect on structural and magnetic properties of Ti/Ni multilayer (ML) up to 600 °C have been studied and reported in this paper. Ti/Ni multilayer samples having constant layer thicknesses of 50 Å each are deposited on float glass and Si(1 1 1) substrates using electron-beam evaporation technique under ultra-high vacuum (UHV) conditions at room temperatures. The micro-structural parameters and their evolution with temperature for as-deposited as well as annealed multilayer samples up to 600 °C in a step of 100 °C for 1 h are determined by using X-ray diffraction (XRD) and grazing incidence X-ray reflectivity techniques. The X-ray diffraction pattern recorded at 300 °C annealed multilayer sample shows interesting structural transformation (from crystalline to amorphous) because of the solid-state reaction (SSR) and subsequent re-crystallization at higher temperatures of annealing, particularly at ≥400 °C due to the formation of TiNi₃ and Ti₂Ni alloy phases. Sample quality and surface morphology are examined by using atomic force microscopy (AFM) technique for both as-deposited as well as annealed multilayer samples. In addition to this, a temperature dependent dc resistivity measurement is also used to study the structural transformation and subsequent alloy phase formation due to annealing treatment. The corresponding magnetization behavior of multilayer samples after each stage of annealing has been investigated by using Magneto-Optical Kerr Effect (MOKE) technique and results are interpreted in terms of observed micro-structural changes.     

Liquid phase oxidation of p-chlorotoluene to p-chlorobenzaldehyde over cobalt-doped mesoporous titania with a crystalline framework

Cobalt-doped mesoporous titania with a crystalline framework synthesized by surfactant templating method presented highly selective (99%) and reasonable conversion rate (49%) of catalytic oxidation of para-chlorotoluene to para-chlorobenzaldehyde in acetic acid using aqueous hydrogen peroxide as oxidant for the first time. Recycling of the catalyst indicates that the catalyst can be used a number of times without losing its activity to a greater extent. By contrast, cobalt-doped mesoporous titania without a crystalline structure and cobalt doped the commercial titania, Degussa P25 prepared by impregnation method with the similar concentration of cobalt were found inactive. The effects of catalyst concentration, reaction time, reaction temperature, and solvents on the performance of the catalyst were also investigated.     

Microstructure of laser melted Al18B4O33w/2024Al composite

The microstructure of a laser treated Al₁₈B₄O₃₃w/2024Al composite has been investigated using transmission electron microscope (TEM), low-angle (glancing angle) X-ray diffraction (XRD) techniques. Various surface microstructures were observed in the laser treated composite. The Al₁₈B₄O₃₃ whisker on the surface of the composite was decomposed during laser surface melting, various decomposition products were studied in the laser treated composite. Eutectic phases and the precipitation in the matrix of the composite with laser-treated were observed. The main phases detected in the molten zone were aluminum and decomposition products Al₂O₃. The effect of laser treatment on the hardness of the composite was also examined. A surface hardness of 400 Hv was noted.     

Precise measurement of magnetic moment of short-lived β-emitting nuclei12B ( I π=1+, T 1/2=20.18 ms)

The spin polarized β-emitting nuclei¹²B (I ^π=1⁺,T _1/2=20.18 ms) were produced by the nuclear reaction¹¹B(d, p)¹²B and by the selection technique of the incident deuteron energy and the¹²B recoil angle following the nuclear reaction. The nuclear magnetic moment of the short-lived nuclei¹²B was measured by β-NMR with the β-NMR and β-NQR setup established for the first time in China. The nuclear magnetic moment of¹²B was determined to be μ=0.99993±0.00048 nm org=0.99993±0.00048 after the precise correction of the Knight shift.     

Multilayer optics for XUV spectral region: technology fabrication and applications

We present research investigations in the field of multilayer optics in X-ray and extreme ultra-violet ranges (XUV), aimed at the development of optical elements for applications in experiments in physics and in scientific instrumentation. We discuss normal incidence multilayer optics in the spectral region of “water window”, multilayer optics for collimation and focusing of hard X-ray, multilayer dispersing elements for X-ray spectroscopy of high-temperature plasma, multilayer dispersing elements for analysis of low Z-elements. Our research pays special attention to optimization of multilayer optics for projection EUV-lithography (ψ-13nm) and short period multilayer optics.     

Photoelectron spectroscopic study of Li oxides on Li over-deposited V2O5 thin film surfaces

The Li oxides species formed on Li over-deposited V₂O₅ thin film surfaces have been studied by using X-ray and UV induced photoelectron spectroscopy (XPS and UPS). The photoelectron spectroscopic data show that the Li over-deposited V₂O₅ system itself is not stable. Further chemical decomposition reactions are taken place even under UHV conditions and lead to form Li₂O and Li₂O₂ compounds on the surface. The formation of Li₂O₂ causes to arise an emission line at about 11.3 eV in the valence band spectra.