盐酸后处理制备高效制氢光催化剂Zn2In2S5

采用水热法制备了ZnIn₂S₄固溶体, 并通过用盐酸对其进行后处理获得了系列Zn_mIn₂S_m+3(m≥2, 整数)固溶体. 通过X射线衍射(XRD)、 扫描电子显微镜(SEM)、 透射电子显微镜(TEM)、 X射线光电子能谱(XPS)、 紫外-可见漫反射光谱(UV-Vis DRS)、 荧光光谱(PL)和电化学测试对催化剂的组成、 结构和性能进行了表征. 研究了系列固溶体可见光光催化制氢活性. 结果表明, ZnIn₂S₄固溶体经0.5 mol/L HCl处理后能转化为Zn₂In₂S₅固溶体, 其制氢活性为ZnIn₂S₄固溶体的2.2倍, 并且具有良好的稳定性.     

278.15～318.15 K下葡萄糖在盐酸中的体积性质

测定了278.15～318.15 K(间隔10 K)下葡萄糖＋HCl＋水三元体系的密度, 计算了葡萄糖在盐酸(浓度0.2～2.1 mol•kg^–1)中的表观摩尔体积V_Φ,G、标准偏摩尔体积V⁰_Φ,G、葡萄糖-HCl在水中的体积对相互作用参数V_EG和标准偏摩尔膨胀系数(∂V⁰_Φ,G/∂T)_p. 结果表明: (1)葡萄糖在盐酸中的表观摩尔体积随葡萄糖和HCl的浓度的增加而线性增大; (2) V⁰_Φ,G随HCl的质量摩尔浓度的增加而线性增大; (3)葡萄糖与HCl在水溶液中的体积相互作用参数V_EG＞0, 但数值对温度变化不甚敏感; (4)葡萄糖在水和盐酸中的V⁰_Φ,G值随实验温度的变化关系均可表示为: V⁰_Φ,G＝a₀＋a₁(T－273.15 K) ^2/3; (5) (∂V⁰_Φ,G/∂T)_p为正值且随温度的升高而减小; 在一定温度下, 其值随HCl浓度的增加而稍稍减小. 糖的水化程度随温度的升高和HCl的浓度的增加而减小. 用结构相互作用模型对葡萄糖与HCl之间的体积相互作用进行了解释.     

毛细管电泳用于水产品中五种抗生素的同时测定

用毛细管电泳-紫外检测法同时测定水产品中的四环素(TC)、金霉素(CTC)、土霉素(OTC)、多西环素(DC)及氯霉素(CAP)的含量．研究了缓冲体系的酸度、浓度、添加剂、分离电压、进样时间以及温度等条件对分离的影响,得到了电泳的最优条件．在278nm波长处,分离电压为22kV,20mmol／L磷酸氢二钠-10mmol／L柠檬酸(pH值2．8,含0．25mmol／L Na2EDTA和体积分数为4．0％的吐温-80)运行缓冲液下,上述5种组份在25min内得到完全分离．5种抗生素的质量浓度和电泳峰面积在2．5～300．0mg／L和10．0～300．0mg／L范围内呈现良好的线性,TC、CTC、OTC、DC和CAP的相关系数(r)分别为0．9996、0．9992、0．9993、0．9934、0．9987,检测下限为0．5～1．5μg／mL。该方法灵敏度高,重现性好,操作简便,并已成功用于水产品鲫鱼中的5种抗生素残留的检测。     

CrO3.CH3NH2.HCl／Al2O3的制备及其对苯偶姻体系的氧化反应

ＣｒＯ３·ＣＨ３ＮＨ２·ＨＣｌ／Ａｌ２Ｏ３的制备及其对苯偶姻体系的氧化反应张贵生＊石启增陈密峰蔡昆（河南师范大学化学系新乡４５３００２）关键词ＣｒＯ３·ＣＨ３ＮＨ２·ＨＣｌ／Ａｌ２Ｏ３，苯偶姻，苯偶酰，氧化１９９６－０８－１８收稿，１９９６－１１－０...     

高比表面CexTi1-xO2催化剂的结构表征及其HCl催化氧化性能

以硝酸铈,硫酸钛为前驱体,用氨水共沉淀法制备了一系列CexTi1-xO2催化剂.利用XRD、Raman、N2吸附-脱附、H2-TPR对催化剂进行了表征并考察了其催化HCl氧化制Cl2的性能.结果表明:复合氧化物较CeO2和TiO2更加分散甚至高度弥散,大大增加了其比表面积,最高可达170.5 m2·g-1,同时CeO2与TiO2之间的相互作用显著提高了其可还原氧物种数目,改善了其氧化还原性能.催化反应结果表明,复合氧化物的活性较CeO2和TiO2显著提升,Ce0.1Ti0.9O2表现出了良好的氯化氢催化氧化能力和较好的催化稳定性,在430℃时氯气产率可以达到0.90 gCl2·gcat-1·h-1,反应60 h后,氯气产率稳定在0.76 gCl2·gcat-1·h-1.     

Understanding the adsorption of 4H-1,2,4-triazole derivatives on mild steel surface in molar hydrochloric acid

This study examines the use of some 4H-triazole derivatives, namely 3,5-diphenyl-4H-1,2,4-triazole (DHT), 3,5-bis(4-pyridyl)-4H-1,2,4-triazole (4-PHT) and 3,5-bis(4-methyltiophenyl)-4H-1,2,4-triazole (4-MTHT) for corrosion and dissolution protection of mild steel in normal hydrochloric acid solution. The inhibiting efficiency of the different additives is evaluated by means of weight loss and electrochemical techniques such as ac impedance measurements and polarisation curves. The experimental results obtained reveal that 4-MTHT is the best effective inhibitor and the inhibition efficiency is found to be in the following order: 4-MTHT > 4-PHT > DHT. The variation in inhibitive efficiency mainly depends on the type and nature of the substituents present in the inhibitor molecule. Polarisation curves show that theses triazoles are mixed-type inhibitors in 1 M HCl. The inhibition efficiency increases with 4H-triazole derivatives concentration and attains the maximum value of 99.6% in the case of 4-MTHT at 5 × 10⁻⁴ M. The results obtained from weight loss electrochemical studies were in reasonable agreement. The adsorption of 4H-triazole derivatives on the steel surface obeys to the Langmuir isotherm model. The thermodynamic data of adsorption and activation are determined and discussed. The fundamental thermodynamic functions were used to glean important information about the 4H-triazoles inhibitory behaviour. Molecular modeling was used to get better insight, about structural and electronic effects in relation to the inhibition efficiencies.     

Ultrasound-assisted soil washing processes for the remediation of heavy metals contaminated soils: The mechanism of the ultrasonic desorption

Ultrasound-assisted soil washing processes were investigated for the removal of heavy metals (Cu, Pb, and Zn) in real contaminated soils using HCl and EDTA. The ultrasound-assisted soil washing (US/Mixing) process was compared with the conventional soil washing (Mixing) process based on the mechanical mixing. High removal efficiency (44.8% for HCl and 43.2% for EDTA) for the metals was obtained for the most extreme conditions (HCl 1.0 M or EDTA 0.1 M and L:S = 10:1) in the Mixing process. With the aide of ultrasound, higher removal efficiency (57.9% for HCl and 50.0% for EDTA) was obtained in the same extreme conditions and similar or higher removal efficiency (e.g., 54.7% for HCl 0.5 M and L:S = 10:1 and 50.5% for EDTA 0.05 M and L:S = 5:1) was achieved even in less extreme conditions (lower HCl or EDTA concentration and L:S ratio). Therefore, it was revealed that the US/Mixing was advantageous over the conventional Mixing processes in terms of metal removal efficiency, consumption of chemicals, amount of generated washing leachate, and volume/size of washing reactor. In addition, the heavy metals removal was enhanced for the smaller soil particles in the US/Mixing process. It was due to more violent movement of smaller particles in slurry phase and more violent sonophysical effects. In order to understand the mechanism of ultrasonic desorption, the desorption test was conducted using the paint-coated beads with three sizes (1, 2, and 4 mm) for the free and attached conditions. It was found that no significant desorption/removal of paint from the beads was observed without the movement of beads in the water including floatation, collision, and scrubbing. Thus, it was suggested that the simultaneous application of the ultrasound and mechanical mixing could enhance the physical movement of the particles significantly and the very high removal/desorption could be attained.     

What we have learned from studies on chemical properties of amorphous alloys?

Amorphous alloys have many attractive characteristics including extremely high corrosion resistance if the sufficient amounts of corrosion-resistant elements are added. The superiority of amorphous alloys is based on the homogeneous single phase nature without any chemical and physical heterogeneities. Although there are processing limitations to avoid the formation of heterogeneous crystalline structure in addition to no welding technology without crystallization, the application of corrosion-resistant amorphous alloys is expected particularly to the very aggressive environments, where any conventional crystalline metallic materials cannot be used. Some amorphous bulk alloys showed zero corrosion mass loss due to spontaneous passivation even in 12 M HCl. Production of amorphous bulk alloys became possible for selected compositions. The homogeneous single phase nature is also effective to form useful catalysts with unique composition and structure. An example of catalysts is for carbon dioxide methanation useful for supply of renewable energy in the form of methane.     

Improvement in magnetic properties of La substituted BaFe12O19 particles prepared with an unusually low Fe/Ba molar ratio

In this study, effect of lanthanum substitution on the phase composition, lattice parameters and magnetic properties of barium hexaferrite has been studied in samples synthesized in ammonium nitrate melt. Samples, prepared with different lanthanum amount and having various initial Fe/(Ba+La) ratios in between 12 and 2 {(Ba_1−xLa_x)·n Fe₂O₃, where 0≤x≤1 and 1≤n≤6)}, are sintered at temperatures from 800 to 1200 °C. The lattice parameters, both a and c, decreases with increasing La amount which results in a decrease of the unit cell volume. The scanning electron microscope micrographs show that the pure and La-substituted sample with x=0.3, both calcinated at 1000 °C, have grain sizes smaller than 1 μm. The coercivities of the La-substituted samples increase with increasing La amount and reaches to a maximum value of 5.73 kOe, when x=0.3. Sintering at higher temperatures (above 1000 °C) decreases the coercivity, resembling a transition from single to multi-domain behavior of the particles, while saturation magnetization of the samples continues to increase due to the increasing grain size. Magnetization measurements of the samples prepared with different Fe/(Ba+La) molar ratios, n's, revealed that the specific saturation magnetization slightly increases with decreasing n, while coercivities fluctuates around 5.5 kOe. However, a sharp increase in the saturation magnetization has been observed in the sample having n=1 and washed in HCl. It was measured as 59.2 emu/g at 15 kOe, which is higher than that of the pure sample (57.5 emu/g). Thus, the magnetic parameters are optimized in the sample Ba_0.7La_0.3Fe₁₂O₁₉ so as to maximize both coercivity and specific saturation magnetization in the HCl-washed sample synthesized by starting with an unusually low Fe/(Ba+La) molar ratio of 2 (or n=1).     

Three Spectrophotometric Methods for the Determination of Oxomemazine Hydrochloride in Bulk and in Pharmaceutical Formulations Using Bromocresol Green,Congo Red,and Methyl Orange

Abstract

Three simple, sensitive, and highly accurate spectrophotometric methods have been developed for the determination of oxomemazine hydrochloride (OXO‐HCl) in bulk and in pharmaceutical formulations. These methods are based on the formation of yellow ion‐pair complexes between the examined drug and bromocresol green (BCG), congo red (CR), and methyl orange (MO) as reagents in universal buffer solution of pH 3.0, 5.5, and 3.5, respectively. The formed complexes were extracted with chloroform and measured at 413, 495, and 484 nm, respectively for the three systems. The best conditions of the reaction were studied and optimized. Beer's law was obeyed in the concentration ranges 2.0–18.0, 2.0–14.0, and 2.0–16.0 µg ml^?1 with molar absorptivity of 4.1×10⁴, 1.1×10⁴, and 3.5×10⁴ mol^?1cm^?1, for the BCG, CR, and MO methods, respectively. Sandell's sensitivity, correlation coefficient, detection, and quantification limits are also calculated. The proposed methods have been applied successfully for the analysis of the drug in pure and in its dosage forms. No interference was observed from common pharmaceutical excipients and additives. Statistical comparison of the results with those obtained by HPLC method shows excellent agreement and indicates no significant difference in accuracy and precision.