CRYSTAL STRUCTURE AND MORPHOLOGY OF NASCENT SAMPLES OF SYMMETRIC AROMATIC POLYESTERS——Ⅱ. POLY(p-PHENYLENE 2,6-NAPHTHALATE)

Confined thin film melt polymerization (CTFMP) of naphthalene chloride/hydroquinone (NCMQ, 1/1, molar)mixtures at polymerization temperatures (T_p) below ca. 300℃ resulted in relatively thick, elongated crystals. Polymerizationof NC/HQ above 300℃ between glass yielded well-formed lamellar crystals ca. 100 A thick. Phase Ⅰ and Ⅱ [001] EDpatterns were obtained for all T_p, the relative amount of phase Ⅰ increasing with T_p. Polymerization of naphthalenedicarboxylic acid/hydroquinione diacetate 1/1 mixtures at high T_p also yielded lamellar crystals that "curled up" off of thesubstrate. When the high temperature CTFMP polymerization was conducted between mica, aggregates of lamellae on-edgedeveloped but epitaxial growth did not occur. Epitaxial growth of lamellae between mica could be obtained, however, byconfined thin film solution polymerization, with both of the latter samples yielding apparently related ED patterns from adifferent unit cell than phase Ⅰ or Ⅱ. Fiber patterns, obtained from sheared samples, indicated considerably greater crystaldisorder than in the nascent crystals. Refinement of the phase Ⅰ unit cell parameters, based on the [001] and [01 1] EDpatterns, with modeling based on Cerius~2, suggests a monoclinic phase Ⅰ unit cell with a = 7.76, b = 5.71, c = 14.99 A, α = γ= 90°, β= 99.7°, ρ = 1.47 g/cm~3, space group P12_1/al.     

The effect of Cu substitution on the A1g mode of La0.7Sr0.3MnO3 manganites

We report on the first Raman data of Cu substituted La_1−ySr_yMn_1−xCu_xO₃ (0≤x≤0.10 and 0.17≤y≤0.3, accordingly in order to have the same Mn⁴⁺/[Mn⁴⁺+Mn³⁺] ratio), collected in the frequency range 100-900 cm⁻¹ and at room temperature, with parallel (e_i∥e_s) and crossed (e_i⊥e_s) polarizations of the incident (e_i) and scattered (e_s) light. Spectra were fitted with a Drude-Lorentz model, and peaks at 190-220 and 430 cm⁻¹, together with two broad structures centered at near 500 and 670 cm⁻¹, have been found. We also have observed that the A_1g mode is substantially shifted with increasing Cu substitution. The A_1g phonon shift is a linear function of the tolerance factor t and the rhombohedral angle α_r, thus following the structural changes of the MnO₆ octahedra in the system.     

Energy storage in Ce-doped LiCaAlF6 and LiSrAlF6 crystals

Absorption, emission and thermoluminescence (TL) of as-grown and X-irradiated pure and Ce-doped LiCaAlF₆ (LiCAF) and LiSrAlF₆ (LiSAF) crystals have been analyzed. It is shown that the energy storage is defined by the dissimilarity of basic matrix properties, intrinsic defect structure, preferred Ce³⁺ ion disposition and charge compensation defect type. This is the reason of higher colorability and TL efficiency of as-grown Ce:LiSAF compared to Ce:LiCAF. Pre-filling of ultra-deep traps leads to enormous increases in the TL response. Due to these properties Ce:LiSAF and Ce:LiCAF are promising thermoluminescent dosimetric materials.     

The synthesis mechanism of Ca3Al2O6 from soft mechanochemically activated precursors studied by time-resolved neutron diffraction up to 1000°C

The reaction pathway for the Ca₃Al₂O₆ formation up to 1300°C, from mechanochemically treated mixtures of amorphous aluminum hydroxide and CaCO₃, was studied in situ by differential thermal analysis, constant heating rate dilatometry and time-resolved neutron powder diffraction. The experiment was carried out, in an open system, on a sample with the nominal Ca₃Al₂O₆ stoichiometry. The results obtained by neutron diffractometry and thermal analysis were in good agreement with the data obtained by scanning electron microscopy and X-ray diffraction on heat-treated and-quenched samples. The synthesis path implied the formation of cryptocrystalline Al₂O₃, crystalline CaO, CaAl₂O₄ and Ca₁₂Al₁₄O₃₃ as transitory phases. Finally the nucleation and growth of the single phase Ca₃Al₂O₆ took place at 1300°C and exhibited porous structure due to CO₂ and H₂O release.     

New 6-Arylsulfonyl-1,2-benzoisothiazol-3(2H)-one 1,1-Dioxides Derived from Diphenyl Sulfone Monosulfonyl Chlorides

Various methods were studied for the oxidation of 2-methyl-5-(phenylsulfonyl)benzenesulfamide and its derivatives. The oxidation by sodium dichromate in sulfuric acid was found most efficient. The effects of temperature, concentration, reagent ratio, and time of the oxidation reaction on the yield of the desired product were investigated. Conditions were proposed for obtaining the desired product in yields up to 95%. A synthesis was developed for a series of new saccharin derivatives.     

含k-次增生算子的Ishikawa迭代的收敛性问题

主要研究了非线性方程x Tx=f的Ishikawa迭代解．其中T为k-次增生的或增生的，并在一致光滑和任意的实Banach空间分别研究了上述方程的带误差的Ishikawa迭代解，从而推广了已知的一些结果。     

Fatigue Loading and Life Prediction in Three Fretting Fatigue Fixtures

Three fixtures for conducting laboratory fretting fatigue tests are described and their respective testing methods and the results of the analysis are compared. Each of these fixtures has been used to investigate the effects of various parameters of interest in fretting fatigue. These fixtures include a unique apparatus in which all load applied to the specimen is transferred to the fretting pads, an apparatus similar to many found in the literature where partial load transfer occurs across the pads, and a simplified dovetail fixture in which the clamping load, P, and the shear load, Q, are varied in phase. Select test conditions from prior experiments performed on identical material and resulting in similar lives ranging from one to ten million cycles from these fixtures are identified. The various testing conditions were used to compute the unique stress field for each case. The resulting contact stresses were used to calculate crack initiation based criteria, and to calculate stress intensity factors. The three fixtures were shown to be able to accommodate a range of loads, fretting pad contours, and specimen geometries that produced a variety of stress fields. A crack-initiation-based criterion was shown to predict the failure lives of thinner specimens accurately. The stress intensity factor calculations showed the possibility of a crack arresting for a stress field that decays rapidly and the possibility of a local minimum for K as a function of depth. The fixtures are shown to be complementary in generating data for development of robust fretting fatigue models that use these criteria.