采用空心阴极放电等离子体化学气相沉积方法制备a-CH薄膜

 研究了不同衬底-阴极距离、直流电压和H₂流量对a-CH薄膜沉积速率的影响。结果表明：衬底-阴极距离必须大于0.5cm，随着该距离的增加，薄膜的沉积速率减少；直流电压达550V时沉积速率最大；随着H2含量的增加，CH₄含量相对减少，沉积速率随之降低。用AFM观察了以该方法制得的448.4nm CH薄膜的表面形貌，表面粗糙度约为10nm。最后测出了不同条件下CH薄膜的UV-VIS谱，由此可以计算得到薄膜的禁带宽度及折射率。     

射流式单重态氧发生器研究

单重态氧O2 (a1Δg)是迄今唯一能用纯化学反应高效产生的具有长寿命的亚稳激发态分子 .为了考察提出的用两个O2 (1Δ)能量汇集反应生成氧第二单重激发态O2 (b1Σ+ g)以实现近可见短波长化学激光方案的现实性 ,设计和实验了一个氯流量为 3～ 10mmol/s的射流式单重态氧发生器 (JSOG) .考察了三种具有不同孔径和孔数目的喷头、氯气流量和脱水冷阱温度等对JSOG出口的O2 (1Δ)浓度、O2 (1Δ)分压、氯利用率及水蒸气含量的影响 .发现用聚氯乙烯管作冷阱时 ,最佳冷阱介质温度为 - 140～ - 15 0℃ ,对此提出了O2 (1Δ)表面脱活与脱水互相竞争的解释 .在最佳条件下 ,可将O2 (1Δ)气中水分压降低至 4Pa ,这一结果是首次报导     

On practical metrology and chemical analysis: etalons and traceability systems

 National measurement systems are infrastructures to ensure, for each nation, a consistent and internationally recognised basis for measurement. Such complex systems have historical, technical, legal, organisational and institutional aspects to connect scientific metrology with practical measurements. Underlying any valid measurement is a chain of comparisons linking the measurement to an accepted standard. The ways the links are forged and the etalons (measurement standards) to which they connect are defining characteristics of all measurement systems. This is often referred to as traceability which aims at basing measurements in common measurement units – a key issue for the integration of quantitative chemical analysis with the evolving physical and engineering measurement systems. Adequate traceability and metrological control make possible new technical capabilities and new levels of quality assurance and confidence by users in the accuracy and integrity of quantitative analytical results. Traceability for chemical measurements is difficult to achieve and harder to demonstrate. The supply of appropriate etalons is critical to the development of metrology systems for chemical analysis. An approach is suggested that involves the development of networks of specialised reference laboratories able to make matrix-independent reference measurements on submitted samples, which may then be used as reference materials by an originating laboratory using its practical measurement procedures. Received: 31 July 1995 Accepted: 19 August 1995     

Shape transition from InAs quantum dash to quantum dot on InP(3 1 1)A

We report on the shape transition from InAs quantum dashes to quantum dots (QDs) on lattice-matched GaInAsP on InP(3 1 1)A substrates. InAs quantum dashes develop during chemical-beam epitaxy of 3.2 monolayers InAs, which transform into round InAs QDs by introducing a growth interruption without arsenic flux after InAs deposition. The shape transition is solely attributed to surface properties, i.e., increase of the surface energy and symmetry under arsenic deficient conditions. The round QD shape is maintained during subsequent GaInAsP overgrowth because the reversed shape transition from dot to dash is kinetically hindered by the decreased ad-atom diffusion under arsenic flux.     

Microstructure effect on microtopography of chemically etched α + β Ti alloys

Microstructure effect on chemical etching behavior of the annealed Ti-6Al-4V and Ti-3Al-2.5V titanium (Ti) alloys was compared with that of unalloyed commercially pure titanium. The microstructural evolution of structure phases after annealing the titanium and its alloys at temperature near and above β transus and followed by furnace cooling to room temperature was studied using optical microscope, scanning electron microscope and X-ray diffraction techniques. The microstructure study illustrates that the heat treatment enhanced partitioning effect allows extensive formation of hemispherical and near spherical pits roughened surface to be readily acquired by chemically etching the annealed α + β titanium alloys. The kinetics of the chemical etching reaction process show a linear dependence on time. The annealed α + β titanium alloys that exhibit relatively lower weight loss and thickness reduction rate illustrate less chemical activity than the annealed unalloyed titanium.     

Effects of vitrification suppression on structure morphology, conductivity and dielectric properties of vanadium phosphate glasses

Vitrification suppression in the (V₂O₅)_1−x (P₂O₅)_x glasses where x=0.10, 0.15, 0.20, and 0.25 was controlled by changing the rate of quenching glasses. The structure variations occurring in the glasses were detected by differential thermal analysis and optical microscope. The results implied the separation and growth of V₂O₅ orthorhombic microcrystal in the samples with x=0.10 and 0.15 whereas other samples did not illustrate remarkable changes in their microstructure. However, in temperature range between 300 and 473 K a semiconducting behavior for all samples appears during the study of electrical conductivity-temperature dependence. A decrease in conductivity values accompanied with some variations in activation energies by reducing quenching rate was observed. The conductivity results suggested that the conduction occurs by the phonon assisted hopping of a small polaron between V⁴⁺ and V⁵⁺ states at relatively higher temperature range above θ_D/2. Whereas at relatively low temperatures the conduction may occur by electron jumping between filled and empty states at Fermi level in the disordered matrix besides polaronic conduction. Reasonable values for the density of localized states, carrier concentration and carrier mobility were estimated and discussed. Also, dielectric constant and dielectric loss were studied as a function of frequency at different temperatures confirming the structure variations in the glass system.     

EPR investigations of oxidation effects in (V1−xMox)2−δO3

Electron paramagnetic resonance (EPR) investigations has been carried out on the new family of molybdenum doped vanadium sesquioxides (V_1−xMo_x)_2−δO₃. The oxidation effects were monitored from the rate of paramagnetic V⁴⁺ created when the sample is exposed to the air. The effects of the oxidation time, sample temperature, and annealing at 1000 °C under a diluted hydrogen atmosphere on the EPR signal features are analyzed. The V⁴⁺ concentration in the oxidized samples is determined and the relaxation effects driven by the conduction electrons are pointed out from the thermal behaviour of the EPR line features. EPR spectra of all the oxidized samples also reveal a small ferromagnetic contribution strongly correlated with the V⁴⁺ content.     

CID-ICP-AES检测煤中不同形态的硫

研究了CID-ICP-AES检测煤中硫酸盐和硫铁矿形态硫的方法。较现有国标方法快速、简便，常见元素不干扰，加标回收率在98．5％-103．0％之间，10次测定的RSD在0．76％-1．59％之间。     

Organocatalysis: quantum chemical modeling of nucleophilic addition to α,β‐unsaturated carbonyl compounds

One of the successful transformations within the field of organocatalysis, the organocatalytic asymmetric addition of nitromethane to α,β‐unsaturated aldehydes and ketones, has been studied by quantum chemical modeling. The level of accuracy of the hybrid density functional theory method B3LYP/6‐31G(d) was compared to a high level ab initio benchmark for this reaction. It is concluded that B3LYP/6‐31G(d) performs very well for this reaction type, giving good estimates of critical energies. The reaction between acrolein and nitromethane was studied in detail. The reaction mechanism revealed an intermediate oxazolidin structure, which is currently unknown. Alkyl substitution in various positions on the amine catalyst or α,β‐unsaturated carbonyl compound influences the reactivity in a predictive fashion. The iminium ion, prop‐2‐en‐iminium, is less activated towards nucleophilic attack compared to protonated acrolein. Copyright © 2007 John Wiley & Sons, Ltd.