Effect of Al content on the properties of Cr1−xAlxC films prepared by RF reactive magnetron sputtering

Cr_1−xAl_xC films were deposited on high-speed steel by RF reactive magnetron sputtering. In this study, we aimed to identify the effect of the Al content on the properties of Cr_1−xAl_xC films. We found that Cr_1−xAl_xC films exhibited a fine columnar grain microstructure with some special characteristics, such as high hardness of Hv 1426, a low friction coefficient of 0.29, and a large contact angle of 90° for x = 0.18. Furthermore, an increase in Al content resulted in a decrease in film hardness and an increase in contact angle. Moreover, on annealing at 923 K, the mechanical properties of the films improved and a dense protective film of complex Cr₂O₃ and Al₂O₃ oxides was formed on the surface for better wear resistance, which will ultimately increase the lifetime of the high-speed steel substrate.     

Comment on breakup densities of hot nuclei

In [V.E. Viola et al., Phys. Rev. Lett. 93 (2004) 132701, D.S. Bracken et al., Phys. Rev. C 69 (2004) 034612] the observed decrease in spectral peak energies of IMFs emitted from hot nuclei was interpreted in terms of a breakup density that decreased with increasing excitation energy. Subsequently, Raduta et al. [Ad. Raduta et al., Phys. Lett. B 623 (2005) 43] performed MMM simulations that showed decreasing spectral peaks could be obtained at constant density. In this Letter we point out that this apparent inconsistency is due to a selective comparison of theory and data that overlooks the evolution of the fragment multiplicities as a function of excitation energy.     

Some explicit examples of Hamiltonian minimal Lagrangian submanifolds in complex space forms

In this paper, we find some new explicit examples of Hamiltonian minimal Lagrangian submanifolds among the Lagrangian isometric immersions of a real space form in a complex space form.     

<Emphasis Type="Italic">Comment on</Emphasis>¶Low temperature specific heat of blue bronze K <Emphasis Type="Bold">0.30</Emphasis>MoO <Emphasis Type="Bold">3</Emphasis>, by J. Odin,J.C. Lasjaunias,K. Biljaković, K. Hasselbach,and P. Monceau

Eur. Phys. J. B 24, 315 (2001) Here we comment on a recently published paper on the presence of a phason contribution in the low temperature heat capacity data of the charge-density-wave compounds K_0.3MoO₃ and (TaSe₄)₂I. We have shown that the anomaly in the C _P / T ³ data reported by Odin et al. is straightforwardly interpreted in terms of low energy phonon modes resulting from the peculiar topology of these compounds. Received 21 February 2002 Published online 19 July 2002     

An explosion point space without the fixed point property

In 1988 A. Gutek proved that there exist one-point connectifications of hereditarily disconnected spaces that do not have the fixed point property. We improve on this result by constructing a one-point connectification of a totally disconnected space without the fixed point property.     

脉冲磁场处理对碳纳米管掺杂MgB2线材临界电流密度的影响

对碳纳米管(CNT)掺杂MgB₂超导体磁场处理后的行为进行了研究. 结果表明，CNT掺杂MgB₂超导体经5T脉冲磁场处理后临界电流密度J_c(H)在低磁场下提高了2—3倍，高场下提高一个数量级以上，扫描电镜结果显示CNT沿着处理磁场方向规则排列并且成为MgB₂基体的形核中心和高效的磁通钉扎中心. 关键词： 2')" href="#">MgB₂ 碳纳米管 脉冲磁场处理     

Complete systems, elementary submodels and the tightness of upper hyperspaces

We introduce and study some completeness properties for systems of open coverings of a given topological space. A Hausdorff space admitting a system of cardinality κ satisfying one of these properties is of type Gκ. Hence, we define several new variants of the ?ech number and use elementary submodels to determine further results. We introduce M-hulls and M-networks, for M elementary submodel. As an application, we give estimates for both the tightness and the Lindelöf number of a generic upper hyperspace. Two recent results of Costantini, Holá and Vitolo on the tightness of co-compact hyperspaces follow from ours as corollaries.     

自由曲面光学虚拟制造与检测系统的探讨

自由曲面光学产品设计、制造与检测的工艺流程，通常采取试凑法逐次逼近。由于加工 检测 再加工，循环往复，既费时，成本又高，产生了瓶颈问题。为了解决此弊端，本文运用虚拟制造技术，提出光学虚拟制造的基本构想，即虚拟制造系统结构模型，给出光学系统虚拟原型的构成和光学系统成像质量虚拟检测系统的构成，讨论光学成像质量的仿真检测以及敏度分析方法。研究结果表明：运用虚拟制造与检测技术，可缩短研发周期，降低成本，优化工艺并提高产品质量。