含氰基的酚醛树脂及其碳纤维复合材料

含氰基的酚醛树脂，具有优异的耐高温性能和高温下的机械强度，在３１５℃下性能变化甚小；不着火，发烟量低，有良好的加工成型性能。热固化过程中氰基成三嗪环而交联，没有小分子脱出，是一类具有广泛发展前景的新型热固性树脂。     

Carbon–epoxy composites based on fibers coated with nylon 6,6: hygrothermal ageing versus interlaminar shear strength

Carbon fibers were coated in situ with a thin film of polyhexamethylene adipamide by an interfacial polycondensation technique. The modified fibers were used for the preparation of epoxy-based unidirectional composites. Specimens of these materials were immersed in water until equilibrium conditions were attained. The weight gain at equilibrium was determined as a function of the immersion temperature, the fiber volume fraction and the polyamide content deposited on the fibers. Water penetration in specimens made with uncoated carbon fibers increases when the volume fraction decreases. Introduction of the polyamide interlayer initially increases the water absorption, but reduces it at higher immersion temperatures and/or higher polyamide contents. The treated specimens were subjected to the short beam test to determine the interlaminar shear strength (ILSS). The data show that the ILSS decreases with water penetration but increases when the immersion temperature increases from 40 to 70°C. The overall performance encountered is discussed in terms of the possible roles of the polyamide interphase while taking into account mechanisms concerned with matrix plasticization, interphase degradation and residual stress relaxation.     

Methane activation on Ni(1 1 1): Effects of poisons and step defects

We have, theoretically and experimentally, investigated the dissociation of methane on the terraces and steps of a Ni(1 1 1) surface. Using Density Functional Theory (DFT) total energy calculations combined with Ultra High Vacuum (UHV) experiments, we find that the steps exhibit a higher activity than the terraces. We have, furthermore, investigated how carbon and sulfur present on the surface will deactivate the steps, leaving only the terraces active. We find the intrinsic sticking probabilities of methane on the steps and terraces at 500 K to be 2.8 × 10⁻⁷ for the steps and 2.1 × 10⁻⁹ for the terraces, in complete agreement with our calculated difference in activation energy of 17 kJ/mol.     

Effect of carbon content on the microstructure and the cracking susceptibility of Fe-based laser-clad layer

The laser cladding of Fe-based alloys on a medium carbon steel substrate was performed using a CO₂ laser and Ar shielding gas that was blown into a molten pool. The microstructure and cracking susceptibility of the laser-clad layers were studied in terms of carbon additions. Results show that the small change of the carbon content in the alloy powders can obviously change the microstructure and properties of the layers. When the carbon content is in the range of 0.3–0.4 wt.%, the decrease of the carbon content in alloy powders will increase the hardness and toughness of the layers simultaneously under the same process parameters. As a result, crack-free coatings with high hardness can be obtained. As the carbon content increases from 0.2 wt.% to 0.4 wt.%, the segregation ratio of chromium increases, while the segregation ratios of nickel, manganese, and silicon first decrease and then increase. At the same time, a new designing principle concerning the composition and microstructure has been put forward, and the principal mechanisms of strengthening and toughening of the layers are fine-grain strengthening and low carbon martensitic phase transformation strengthening.     

Preparation of well-aligned carbon nanotubes by pyrolysis of phenolic resin in anodic alumina pores

Well-aligned carbon nanotubes (CNTs) of high quality were synthesized by pyrolysis of phenolic resin at 800 °C in anodic alumina oxide (AAO) pores under argon protection. The innocuous source materials and safe operational conditions permit this method to synthesize well-aligned CNTs in large-scale and low cost. The formation mechanism of the synthesized CNTs is also proposed in this work by a series of visual sketches and is proved with obvious evidence. Firstly, phenolic resin nanotubes form in the template pores through the evaporation of solvent. Heat treatment then transfers these tubes into CNTs.     

Preparation of nanosized ZnO using α brass

Nanosized ZnOs were synthesized on the surface of α brass coated a film of nickel catalyst at 500-700 °C under atmosphere of O₂ and CH₄ gases. The nanosized ZnOs have shapes including pillar, leaf, sheet and rod, which were determined by the synthesis temperature and the flow rates of O₂ and CH₄ gases. The nanosized ZnOs were characterized by electron microscopy including transmission electron microscope for crystal structure, morphology and high resolution images, both field emission scanning electron microscope and scanning electron microscope for morphology, and energy dispersive X-ray spectroscope equipped in electron microscope for chemical composition. A mechanism was proposed for the growth of nanosized ZnO obtained in this work.     

Apparatus for High-Resolution Solid Hydrogen Matrix Isolation Spectroscopy and Its Application

Apparatus integrating a Fourier transform-infrared (FT-IR) spectrometer and a mid-infrared difference frequency generation (DFG) laser spectrometer was built for the study of the matrix isolation spectrum in solid molecular hydrogen. A 3-cm-long molecular hydrogen crystal was grown in a liquid-helium Dewar, and its infrared absorption spectrum in the 1-5 μm region was recorded to test the system. The W₀(0) (ν=0←0, J=6←0) line around 2410 cm⁻¹ of solid hydrogen was investigated with the DFG laser spectroscopy. High-resolution matrix isolation spectrum of CO² co-deposited with hydrogen on a BaF₂ cold plate at liquid-helium temperature was studied.     

Transparent carbon nanotube coatings

Thin networks of carbon nanotubes (CNTs) are sprayed onto glass or plastic substrates in order to obtain conductive transparent coatings. Transparency and conductivity at room temperature of different CNT material are evaluated. CNT coatings maintain their properties under mechanical stress, even after folding the substrate. At a transparency of 90% for visible light we observe a surface resistivity of 1 kΩ/sq which is already a promising value for various applications.     

K＋－SrO－La_2O_3／ZnO催化剂上甲烷氧化偶联反应Ⅰ．催化活性和反应气中添加CO_2的影响

Ｋ＋┐ＳｒＯ┐Ｌａ２Ｏ３／ＺｎＯ催化剂上甲烷氧化偶联反应＊Ⅰ．催化活性和反应气中添加ＣＯ２的影响余林徐奕德＊＊郭燮贤（中国科学院大连化学物理研究所催化基础国家重点实验室，大连１１６０２３）关键词钾离子，氧化锶，氧化镧，氧化锌，金属氧化物催化剂，甲烷，...