氢等离子体处理——一种有效提高碳纳米管场发射性能的方法

研究了经氢等离子体处理后多壁碳纳米管的场发射性能。测量了处理前后样品的电流电压特性和表面形貌。结果表明经氢等离子体处理后,发射性能明显改善,发射点密度由未经处理的104/cm2提高到106/cm2。发现了一种新的碳纳米管结构,称之为多结的碳纳米管,并讨论了样品发射性能提高的可能机理。这种处理提供了一种有效提高发射点密度和基于碳纳米管的平板显示器性能的方法,非常适用于低成本大面积场发射阴极的制作。     

Low voltage electrodeposition of CNx films and study of the effect of the deposition voltage on bonding configurations

Carbon nitride (CN_x) films were deposited from acetonitrile at low voltage (150-450 V) through electrodeposition. The films were characterized by atomic force microscopy (AFM), Raman spectroscopy and Fourier transform infrared (FT-IR) spectroscopy. AFM investigations revealed that the grain size was ∼200 nm and roughness was ∼10 nm. The films were found to be continuous and close packed. IR spectra revealed existence of strong sp³, sp² type bonding and weak sp type carbon nitrogen bonds and these bonds were found to increase with voltage. The fraction of sp³-bonded species in the sample increased in low voltage range and after reaching maximum at 350 V, decreased for higher voltages. However, the concentration of sp² CN ring structures in the film increased with increasing voltage. Also, the peak width decreased at low voltages reaching a minimum and increased thereafter. It was observed that the voltage dependent increase in the concentration of polymeric type sp² CN (chain) structures was much more pronounced than that of graphitic type sp² CN (ring) structures. Raman spectra showed the presence of both the D and G bands. The shift in the G band indicated the presence of nitrogen in the film. The I_D/I_G ratio was found to increase with the incorporation of nitrogen. Auger electron spectroscopy (AES) showed a clear increase in the nitrogen content with increase in the voltage. The formation of the film could be explained on the basis of dissociation of electrolyte under applied voltage.     

Au deposits on graphite: On the nature of high temperature desorption peaks in CO thermal desorption spectra

Due to the discovery of Au as a catalyst for low temperature CO oxidation, the adsorption of CO on Au surfaces has attracted a lot of attention recently. On stepped and rough single crystal surfaces as well as on deposited particles two characteristic desorption states above 100 K have been observed via TPD. We have studied Au deposits on graphite in order to elucidate the nature of these desorption peaks in more detail. For this purpose, Au was deposited at 100 K and 300 K on HOPG as a weakly interacting support. In analogy to other supports, we obtain two desorption states (∼140 K and ∼170 K) whose relative intensities depend strongly on the deposition temperature with the high temperature peak being much more pronounced for the 100 K deposits. After annealing to 600 K, both states drastically lose intensity. XP spectra, on the other hand, show virtually no decrease of the Au 4f intensity as would be expected for desorption or significant changes of the particle morphologies. We conclude that both desorption peaks are defect-related and connected with under-coordinated Au atoms that are lost for the most part upon annealing. These sites could be located at the perimeter of dendritic islands or on small, defect-rich particles in addition to larger particles not adsorbing CO at 100 K. Preliminary STM results are in favour of the second interpretation.     

Carbon films grown on Pt(1 1 1) as supports for model gold catalysts

Carbon films were grown on a Pt(1 1 1) single crystal by ethylene decomposition at elevated temperatures (1000-1300 K). Depending on the preparation conditions, different carbon structures formed on the metal surface such as flat and curved graphitic layers, carbon particles and carbon nanowires. Although these carbon films exhibited a high density of surface defects, gold interacted only weakly with the carbon surface. CO adsorption on the Au/carbon systems was very similar to that observed for various Au/oxide systems previously studied. This finding strongly indicates that CO adsorption on gold is essentially independent of the nature of support.     

Adsorption of CO and C2H4 on Rh-loaded thin-film dysprosium oxide

A dysprosium oxide thin film was deposited on Ru(0 0 0 1) by vapor depositing Dy in 2 × 10⁻⁷ torr O₂ while the Ru was at 700 K. The film was ca. 5 nm thick and produced a p(1.4 × 1.4) LEED pattern relative to the Ru(0 0 0 1) substrate. The adsorption and reaction of CO and C₂H₄ adsorbed on Rh supported on the Dy₂O₃ film were studied by TPD and SXPS. The CO initially reacted with loosely bound oxygen in the substrate to produce CO₂. After the loosely bound oxygen was removed, the CO adsorbed non-dissociatively in a manner similar to what is seen on Rh(1 1 1). C₂H₄ adsorbed on the Rh particles and underwent progressive dehydrogenation to produce H₂ during TPD. The C from the C₂H₄ reacted with the O in Dy₂O₃ to produce CO. CO dissociation on the Rh particles could be promoted by treating the Dy₂O₃ with C₂H₄ before CO exposure.     

Adsorption behavior and reaction properties of NO and CO on Rh(1 1 1)

Reactions between NO and CO on Rh(1 1 1) surfaces were investigated using infrared reflection absorption spectroscopy, X-ray photoelectron spectroscopy, and temperature-programmed desorption. NO adsorbed on the fcc, atop, and hcp sites in that order, whereas CO adsorbed initially on the atop sites and then on the hollow (fcc + hcp) sites. The results of experiments with NO exposure on CO-preadsorbed Rh(1 1 1) surfaces indicated that the adsorption of NO on the hcp sites was inhibited by preadsorption of CO on the atop sites, and NO adsorption on the atop and fcc sites was inhibited by CO preadsorbed on each type of site, which indicates that NO and CO competitively adsorbed on Rh(1 1 1). From a Rh(1 1 1) surface with coadsorbed NO and CO, N₂ was produced from the dissociation of fcc-NO, and CO₂ was formed by the reaction of adsorbed CO with atomic oxygen from dissociated fcc-NO. The CO₂ production increased remarkably in the presence of hollow-CO. Coverage of fcc-NO and hollow-CO on Rh(1 1 1) depended on the composition ratio of the NO/CO gas mixture, and a gas mixture with NO/CO ? 1/2 was required for the co-existence of fcc-NO and hollow-CO at 273 K.     

Study of the spontaneous formation of organic layers on carbon and metal surfaces from diazonium salts

This study investigates the spontaneous grafting of different para-substituted phenyl groups on carbon and metallic surfaces from diazonium salts solutions. Glassy carbon, nickel, zinc and iron plates were allowed to react with an acetonitrile solution of aryldiazonium tetrafluoroborate salt by simple dipping. The surfaces were characterized before and after their immersion by XPS and AFM to evidence the formation of a coating on the different materials. The results are indicative of the presence of substituted phenyl groups on all the investigated surfaces. This study also aims at correlating grafting efficiency with metal reactivities and diazonium salt electronic properties by means of AFM and FT-IRRAS. For this purpose, zinc and nickel were chosen due to their opposite reducing properties and two diazonium salts were selected with electron-donor or -withdrawing para-substituents. The results tend to indicate that redox properties of both partners (diazonium + metal) are of prime importance for grafting to occur.     

The growth of carbon nanotubes on montmorillonite and zeolite (clinoptilolite)

Synthesis of carbon nanotubes described in the present work is based on activation of methane in a hot filament CVD reactor and subsequent creation of nanostructures on a catalyst pre-treated polished surface of silicon. An essential step of the synthesis is the use of natural minerals as catalysts. We have studied the catalyst parameters, the way of its application and the amount of Fe³⁺ cations on the surface of aluminosilicates on the quality of the grown nanotube layers. The growth of carbon nanotubes catalyzed by montmorillonite and zeolite (clinoptilolite) was confirmed by scanning electron microscopy and Raman spectroscopy.     

Sonochemical modification of carbon nanotubes for enhanced nanocomposite performance

Multi-walled carbon nanotubes (CNTs) have been treated using 20 kHz ultrasound in combination with dilute nitric and sulfuric acids at much lower concentrations than previously reported. The measurements revealed an optimum set of sonication conditions (in this case 30 min at 12 W cm⁻²) exists to overcome aggregation of the nanotubes and to allow efficient dispersion in ethanol or in chitosan. Transmission electron microscopy and Raman spectroscopy suggested the removal of amorphous material and reduction of the CNT diameter as well as modifications to their defect structures. The surface oxidation was determined by FTIR spectroscopy. At longer times or higher ultrasound intensities, degradation such as nanotube shortening and additional defect generation in the graphitic network occurred and the benefits of using ultrasound decreased. The modified CNTs were used as fillers for chitosan films and gave a tenfold increase in tensile strength and integrity of the films. The methodology was combined with sonochemical generation of gold or iron oxide nanoparticles to produce a range of functional membranes for catalytic reductive hydrogenation or dye degradation under conditions that are more environmentally benign than those previously used. Our results further add to the usefulness of sonochemistry as a valuable tool in preparative materials chemistry but also illustrate the crucial importance of careful control over the experimental conditions if optimum results are to be obtained.