Effect of carbon content on the microstructure and the cracking susceptibility of Fe-based laser-clad layer

The laser cladding of Fe-based alloys on a medium carbon steel substrate was performed using a CO₂ laser and Ar shielding gas that was blown into a molten pool. The microstructure and cracking susceptibility of the laser-clad layers were studied in terms of carbon additions. Results show that the small change of the carbon content in the alloy powders can obviously change the microstructure and properties of the layers. When the carbon content is in the range of 0.3–0.4 wt.%, the decrease of the carbon content in alloy powders will increase the hardness and toughness of the layers simultaneously under the same process parameters. As a result, crack-free coatings with high hardness can be obtained. As the carbon content increases from 0.2 wt.% to 0.4 wt.%, the segregation ratio of chromium increases, while the segregation ratios of nickel, manganese, and silicon first decrease and then increase. At the same time, a new designing principle concerning the composition and microstructure has been put forward, and the principal mechanisms of strengthening and toughening of the layers are fine-grain strengthening and low carbon martensitic phase transformation strengthening.     

Preparation of well-aligned carbon nanotubes by pyrolysis of phenolic resin in anodic alumina pores

Well-aligned carbon nanotubes (CNTs) of high quality were synthesized by pyrolysis of phenolic resin at 800 °C in anodic alumina oxide (AAO) pores under argon protection. The innocuous source materials and safe operational conditions permit this method to synthesize well-aligned CNTs in large-scale and low cost. The formation mechanism of the synthesized CNTs is also proposed in this work by a series of visual sketches and is proved with obvious evidence. Firstly, phenolic resin nanotubes form in the template pores through the evaporation of solvent. Heat treatment then transfers these tubes into CNTs.     

Preparation of nanosized ZnO using α brass

Nanosized ZnOs were synthesized on the surface of α brass coated a film of nickel catalyst at 500-700 °C under atmosphere of O₂ and CH₄ gases. The nanosized ZnOs have shapes including pillar, leaf, sheet and rod, which were determined by the synthesis temperature and the flow rates of O₂ and CH₄ gases. The nanosized ZnOs were characterized by electron microscopy including transmission electron microscope for crystal structure, morphology and high resolution images, both field emission scanning electron microscope and scanning electron microscope for morphology, and energy dispersive X-ray spectroscope equipped in electron microscope for chemical composition. A mechanism was proposed for the growth of nanosized ZnO obtained in this work.     

锥形光纤的偏振特性

随着光通信技术的不断发展，光纤的应用越来越广泛，而锥形光纤以其独特的传光方式越来越多地应用于光纤连接、成像及测量等领域。实验测定了不同锥角和不同长度锥形光纤的偏振特性。理论上，根据麦克斯韦方程组以及边界条件给出了光在理想光纤中的场分布，阐明了实际光纤中光的传输特性。论证了锥形光纤长度与其偏振特性的关系，进而利用几何光学方法对锥形光纤锥角与其偏振特性的关系作了定性说明。并用具体数据进行了定量计算，得出偏振光经锥形光纤传输或耦合后再传输到其终端所得到均是椭圆偏振光的结论。     

光双二进制传输系统的性能研究

光双二进制信号的谱宽是传统二进制信号的一半,采用双二进制传输比二进制传输色散限制的中继距离可增加一倍.本文对采用传统光接收机的光双二进制传输系统用MATLAB进行了通信仿真.结果表明:在完全消光条件下,10 Gb/s双二进制信号在常规单模光纤上传输可达160 km,40 Gb/s双二进制信号在非零色散光纤上为30 km,均比二进制增加了一倍;详细考察了消光比对传输的影响,只有消光比大于25 dB时,双二进制相对于二进制传输的优越性才呈现出来.     

光纤陀螺信号处理中SLD驱动电路设计

光纤陀螺用光源要求输出功率高、相干性低、稳定性好，超辐射发光二极管（SLD）是能满足这些要求的理想光源，目前国内光纤陀螺用的光源基本上主要选择超辐射发光二极管（SLD），从工程实际应用出发，介绍了超辐射发光二极管（SLD）驱动电路设计，以此来提高光纤陀螺性能。     

Apparatus for High-Resolution Solid Hydrogen Matrix Isolation Spectroscopy and Its Application

Apparatus integrating a Fourier transform-infrared (FT-IR) spectrometer and a mid-infrared difference frequency generation (DFG) laser spectrometer was built for the study of the matrix isolation spectrum in solid molecular hydrogen. A 3-cm-long molecular hydrogen crystal was grown in a liquid-helium Dewar, and its infrared absorption spectrum in the 1-5 μm region was recorded to test the system. The W₀(0) (ν=0←0, J=6←0) line around 2410 cm⁻¹ of solid hydrogen was investigated with the DFG laser spectroscopy. High-resolution matrix isolation spectrum of CO² co-deposited with hydrogen on a BaF₂ cold plate at liquid-helium temperature was studied.     

10瓦级双包层光纤激光器

考虑到所用大功率激光二极管的光谱特性，对光纤激光器的基本法布里-珀罗腔型稍加改变，研制出激光二极管抽运的10w级双包层光纤激光器，获得最高功率为11．8w、波长1100mm的单模激光输出。     

Transparent carbon nanotube coatings

Thin networks of carbon nanotubes (CNTs) are sprayed onto glass or plastic substrates in order to obtain conductive transparent coatings. Transparency and conductivity at room temperature of different CNT material are evaluated. CNT coatings maintain their properties under mechanical stress, even after folding the substrate. At a transparency of 90% for visible light we observe a surface resistivity of 1 kΩ/sq which is already a promising value for various applications.