Design and application of phase photon sieve

The imaging principle of Fresnel zone plate and photon sieve were analyzed in this paper. The design and fabrication of phase photon sieve were discussed. The feasibility of using phase photon sieve to realize nano-lithography was analyzed, a novel lithography experiment system based on phase photon sieve was presented, which not only has higher resolution and image contrast than the Fresnel zone plate lithography but also have higher diffractive efficiency than the amplitude photon sieve lithography.     

Physics and applications of aligned carbon nanotubes

Ever since the discovery of carbon nanotubes (CNTs) by Iijima in 1991, there have been extensive research efforts on their synthesis, physics, electronics, chemistry, and applications due to the fact that CNTs were predicted to have extraordinary physical, mechanical, chemical, optical, and electronic properties. Among the various forms of CNTs, single-walled and multi-walled, random and aligned, semiconducting and metallic, aligned CNTs are especially important since fundamental physics studies and many important applications will not be possible without alignment. Even though there have been significant endeavors on growing CNTs in an aligned configuration since their discovery, little success had been realized before our first report on growing individually aligned CNTs on various substrates by plasma-enhanced chemical vapor deposition (PECVD) [Science 282 (1998) 1105–1108]. Our report spearheaded a new field on growth, characterization, physics, and applications of aligned CNTs. Up to now, there have been thousands of scientific publications on synthesizing, studying, and utilizing aligned CNTs in various aspects. In this communication, we review the current status of aligned CNTs, the physics for their alignment, their applications in field emission, optical antennas, subwavelength light transmission in CNT-based nanocoax structures, nanocoax arrays for novel solar cell structures, etc.

The focus of this review is to examine various aligned CNT systems, either as an individual or as an array, either the orientation is vertical, parallel, or at other angles to the substrate horizon, either the CNT core structures are mostly hollow channels or are composed of complex compartments. Major fabrication methods are illustrated in detail, particularly the most widely used PECVD growth technique on which various device integration schemes are based, followed by applications whereas current limitations and challenges will also be discussed to lay down the foundation for future developments.     

Effect of deposition power and pressure on rate deposition and resistivity of titanium thin films grown by DC magnetron sputtering

ABSTRACT

Based on magnetron sputtering deposition technology, titanium (Ti) thin films are deposited on silicon (Si) substrate using different preparation conditions such as sputtering power and pressure. The influence of altering these conditions on deposition rate and microstructure is studied. The results show that sputtering power significantly affects the rate of deposition and the resistivity. The deposition rate of the Ti thin film increases when the resistivity decreases under sputtering powers of 150–225?W with a pressure of 0.8?Pa and Argon (Ar) flux of 80 sccm. As sputtering power was increased further (from 225 to 250?W), the deposition rate reduced and the resistivity augmented. Pressure also has influence on the deposition rate and resistivity – when pressure increases from 0.6 to 0.8?Pa, the deposition rate escalates while the resistivity reduces; when the pressure is raised from 0.8 to 1.0?Pa with Ar flux of 100 sccm, the deposition rate decreases and resistivity increases. The surface chemical compositions and the structures of the Ti film were studied by using X-ray photoelectron spectroscopy (XPS) and X-ray diffractometer (XRD). Observing the cross-section of the thin-film samples produced by scanning electron microscope (SEM) reveals the influence of the preparation conditions used on the microstructure and confirms the influence of sputtering power and pressure on the resistivity.     

Strong water repellency effect on SiO<Subscript>2</Subscript> films processed at a nanometric scale

The present study deals with the creation of nano-rough surfaces with stable and controlled high hydrophobicity. These surfaces were obtained by combining the ion track etching technique with a simple functionalization by grafting perfluoroctyltrichlorosilane (PFOTS) molecules. Surface morphology was investigated by AFM observations which evidenced a self-affine fractal structure with a fractal dimension D_f ~ 2.6. The study of the wetting properties of these surfaces allowed to elucidate the conditions for observing a high hydrophobicity phenomenon and to predict the contact angle values for surfaces designed at a nanometric scale.     

Mass cultivation of various algal species and their evaluation as a potential candidate for lipid production

Microalgae have been proposed as a promising source for biodiesel production. Focusing on algal strains for biodiesel production, efforts should be made to search new strains. Experiments were carried out to investigate the effects of growth parameters (nutrients, pH, light, aeration and temperature) and the oil percentage of eight algal strains (Chlorella sp., Cladophora sp., Hydrodictylium sp., Oedogonium sp., Oscillatoria sp., Spirogyra sp., Stigeocolonium sp., Ulothrix sp.). Results show that 6.5–7.5 is the optimum pH for the growth of all algal species. Temperature showed a greater variation (25°40°C). Ulothrix sp. gave more biomass productivity and is the most suitable strain for biodiesel production due to higher oil percentage (62%). Least biomass production was observed for Stigeocolonium sp. and least oil content was obtained from Hydrodictylium sp. It was observed that among these eight algal strains for biodiesel production, Ulothrix and Chlorella are the most promising algae species.     

In situ fabrication of nanostructured titania coating on the surface of titanium wire: A new approach for preparation of solid-phase microextraction fiber

Nanostructured titania-based solid-phase microextraction (SPME) fibers were fabricated through the in situ oxidation of titanium wires with H₂O₂ (30%, w/w) at 80 °C for 24 h. The obtained SPME fibers possess a ∼1.2 μm thick nanostructured coating consisting of ∼100 nm titania walls and 100-200 nm pores. The use of these fibers for headspace SPME coupled with gas chromatography with electron capture detection (GC-ECD) resulted in improved analysis of dichlorodiphenyltrichloroethane (DDT) and its degradation products. The presented method to detect DDT and its degradation products has high sensitivity (0.20-0.98 ng L⁻¹), high precision (relative standard deviation R.S.D. = 9.4-16%, n = 5), a wide linear range (5-5000 ng L⁻¹), and good linearity (coefficient of estimation R² = 0.991-0.998). As the nanostructured titania was in situ formed on the surface of a titanium wire, the coating was uniformly and strongly adhered on the titanium wire. Because of the inherent chemical stability of the titania coating and the mechanical durability of the titanium wire substrate, this new SPME fiber exhibited long life span (over 150 times).     

Physics of transparent conductors

Transparent conductors (TCs) are materials, which are characterized by high transmission of light and simultaneously very high electrical DC conductivity. These materials play a crucial role, and made possible numerous applications in the fields of electro-optics, plasmonics, biosensing, medicine, and “green energy”. Modern applications, for example in the field of touchscreen and flexible displays, require that TCs are also mechanically strong and flexible. TC can be broadly classified into two categories: uniform and non-uniform TC. The uniform TC can be viewed as conventional metals (or electron plasmas) with plasma frequency located in the infrared frequency range (e.g. transparent conducting oxides), or ultra-thin metals with large plasma frequency (e.g. graphen). The physics of the nonuniform TC is much more complex, and could involve transmission enhancement due to refraction (including plasmonic), and exotic effects of electron transport, including percolation and fractal effects. This review ties the TC performance to the underlying physical phenomena. We begin with the theoretical basis for studying the various phenomena encountered in TC. Next, we consider the uniform TC, and discuss first the conventional conducting oxides (such as indium tin oxide), reviewing advantages and limitations of these classic uniform electron plasmas. Next, we discuss the potential of single- and multiple-layer graphene as uniform TC. In the part of the paper dealing with non-uniform metallic films, we begin with the review of random metallic networks. The transparency of these networks could be enhanced beyond the classical shading limit by the plasmonic refractive effects. The electrical conduction strongly depends on the network type, and we review first networks made of individual metallic nanowires, where conductivity depends on the inter-wire contact, and the percolation effects. Next, we review the uniform metallic film networks, which are free of the percolation effects and contact problems. In applications that require high-quality electric contact of a TC to an active substrate (such as LED or solar cells), the network performance can be optimized by employing a quasi-fractal structure of the network. We also consider the periodic metallic networks, where active plasmonic refraction leads to the phenomenon of the extraordinary optical transmission. We review the relevant literature on this topic, and demonstrate networks, which take advantage of this strategy (the bio-inspired leaf venation (LV) network, hybrid networks, etc.). Finally, we review “smart” TCs, with an added functionality, such as light interference, metamaterial effects, built-in semiconductors, and their junctions.     

Microfluidic platform serves as controllable fabrication of binary Mo/Ir nanodots/carbon hetero-material for efficient electrocatalytic nitrogen reduction

Electrocatalytic nitrogen reduction reaction (NRR) is regarded as a potential routine to achieve environment-friendly ammonia production, because of its abundant nitrogen resources, clean energy utilization and flexible operation. However, it is hindered by low activity and selectivity, in which condition well-designed catalysts are urgently in need. In this work, a binary Mo/Ir nanodots/carbon (Mo/Ir/C) hetero-material is efficiently constructed via microfluidic strategy, of which the nanodots are homogeneously distributed on the carbon skeleton and the average size is approximately 1 nm. Excellent performance for NRR is obtained in 1 mol L⁻¹ KOH, of which the optimized ammonia yield and faradic efficiency are 7.27 μg h⁻¹ cm⁻² and 2.31% respectively. Moreover, the optimized ammonia yield of 6.20 μg h⁻¹ cm⁻² and faradic efficiency of 10.59% are also obtained in 0.005 mol L⁻¹ H₂SO₄. This work achieves the continuous-flow synthesis and controllable adjustment of hetero-materials for favorable morphologies, which provides an innovative pathway for catalyst design and further promotes the development of ammonia production field.     

铜锌锡硫薄膜材料及其器件应用研究进展

铜锌锡硫薄膜材料组成元素储量丰富, 环境友好, 成本低廉, 成为最具前景的薄膜材料之一. 目前, Cu₂ZnSn(S, Se)₄ (CZTSSe)薄膜太阳电池的最高转换效率已经达到12.6%. 本文总结了Cu₂ZnSnS₄ (CZTS)的发展历史, 依次介绍了CZTS薄膜材料的结构特性、光学特性、电学特性、界面特性和Na对CZTS 薄膜的影响, 详细介绍了CZTS薄膜的制备方法及器件应用的最新研究进展, 总结了目前CZTS薄膜太阳电池发展中存在的问题, 展望了今后的研究方向.