硬脂酸/异氰酸酯摩尔比对聚丙烯/木粉复合材料性能的影响

用甲苯-2,4-二异氰酸酯（TDI）和硬脂酸（SA）复合改性木粉,在双螺杆挤出机中制备了聚丙烯（PP）基的木塑复合材料（WPC）,研究了SA/TDI摩尔比对木粉表面性能、复合材料力学性能和加工性能的影响。 结果表明,随着SA/TDI摩尔比的增大,改性木粉的表面张力逐渐减小,与PP的界面张力先减小后增大;与未改性的WPC相比,SA/TDI复合改性剂对WPC的拉伸强度、弯曲强度、缺口冲击强度影响不明显,但对无缺口冲击强度提升较大;当SA/TDI摩尔比为1.07时,复合材料的无缺口冲击强度和熔体质量流动速率分别达到9.74 kJ/m2和13.12 g/10 min,分别比未改性WPC提高了77%和22%。     

微波消解ICP-AES法测定玩具塑料中镉

采用微波加压消解溶样，ICP-AES法测定玩具塑料中镉含量，选择最佳工作条件，方法简便、快速、可靠。适用于各类玩具塑料中镉含量的分析。     

PC聚合物的再利用研究

聚碳酸酯(PC)是手机外壳常用材料,它是一种综合性能优异的热塑性工程塑料,具有较高的回收价值.采用熔融再生方法分别对同种无涂层手机外壳、浅色混杂带涂层和深色混杂带涂层手机外壳三种PC回收料进行了再生利用,对注塑样品进行了力学性能测试,并对断口进行了分析.研究结果表明,三种PC回收料再生后拉伸强度和弯曲强度值较为接近,其中拉伸强度略低于PC原生料,而弯曲强度高于原生料.无涂层PC回收料延伸率和冲击韧性分别达到了24kJ/m2和65;,而混杂带涂层回收料只有它的一半左右.     

分块法研究圆柱绕流升阻力

 使用新的分块耦合方法，分别对单圆柱和串列双圆柱绕流进行了数值 模拟. 对于单圆柱绕流，低$Re$下计算所得到的定常涡尺寸与实验非常接近. 对于 串列双圆柱绕流，研究分析了改变双圆柱中心间距对上下游圆柱的升阻力系数和脉动频率所 产生的影响，计算结果与实验非常吻合，为进一步研究涡致振动提供了依据.     

有限宽板孔边弹塑性变形测试

测量应变集中区域的弹塑性变形，对于研究材料损伤或微裂纹的产生，以预防宏观裂纹的产生及扩展具有重要的意义。为给航空发动机轮盘的损伤容限设计研究提供相关材料的力学实验参数，做了两个有限宽中心带孔试件的拉伸试验。试验中，采用单调逐级加、卸栽的循环加栽方式，并应用自动网格法和数字图像相关技术测量了孔用的全场位移分布。再应用最小二乘法将离散的位移分量拟合成二元多项式函数，求解出拉伸方向的应变分布，并给出孔边应力σ与孔边应变εy的关系曲线。     

非稳态载荷下轮轨滚动接触及其钢轨波磨研究

利用有限元法,考虑材料反复滚压条件下棘轮效应和局部滑动的影响,研究了非稳态机车和车辆车轮载荷作用下轮轨滚动接触的弹塑性应力、应变和变形,进而分析了塑性流动型钢轨波浪形磨损的形成和发展过程以及波谷和波峰处材料的力学行为.结果表明:在非稳态载荷作用下,钢轨接触表面产生不均匀塑性变形引起的波磨,波磨发展速率呈衰减趋势,最终趋于稳定状态;在相同载荷下,与车辆车轮相比,机车车轮对钢轨波磨影响较大;波谷处的残余应力、应变和变形大于波峰处.     

Two-parameter failure criterion for elastoplastic bodies with mode I cracks

The generalized Dugdale crack model is used to formulate two-parameter failure criteria for the cases of quasibrittle state and developed plastic zones at a mode I crack tip. The failure criteria relate the fracture strength characteristics and the stress mode at the crack tip through the plastic constraint factor. The critical state of bodies with cracks under uni-and biaxial loading is analyzed in the cases of plane stress and plane strain using the Tresca and von Mises yield criteria. A small-scale yield criterion, which is an analytic relation between the critical stress intensity factor and T-stresses, is established __________ Translated from Prikladnaya Mekhanika, Vol. 43, No. 7, pp. 47–57, July 2007.     

A study of time over threshold (TOT) technique for plastic scintillator counter

A new charge measurement method, time over threshold (TOT), has been used in some gas detectors lately. Here TOT is studied for TOF system, made of plastic scintillator counter, which can simplify the electronics of the system. The signal characteristics are measured and analyzed with a high quality oscilloscope, including noise, pedestal, signal amplitude, total charge, rise time and the correlation between them. The TOT and charge are related and can be fitted by some empirical formula. The charge measurement resolution by TOT is given and this will help the design of TOF electronics.     

Iron Nanoparticles in Severe-plastic-deformed Copper

Superparamagnetic iron nanoparticles with a size of a few nanometers were produced in copper by severe plastic deformation. In a isochronal annealing experiment near a temperature of 450K, which corresponds to the temperature of structural relaxation and the first step of grain growth (from 128 to 150nm) of submicrocrystalline copper, an abrupt increase in the magnetic susceptibility is detected. This increase is shown to be due to iron nanoparticles increasing in size from 2.8 to 3.3nm. The vanishing of the ferromagnetic contribution by iron nanoparticles observed at 850K, well below the Curie temperature of iron, is due to the dissolution of nanoparticles in plastically deformed copper.     

弹塑性结构在外载和温度作用下的安定分析

本文在考虑外载和温度的缓慢变化下，提出了一个新的运动安定定理。同时，在此基础上，又导出了既简单又适用的增量破坏准则．文末也以实例说明了它的应用。