硅锗合金Seebeck系数影响因素的研究

作为一种洁净能源,硅锗合金的热电转换性能的研究越来越受到人们的重视.本文重点研究了不同Ge浓度的硅锗合金以及Si、Ge单晶在300～1100K温度范围内,Seebeck系数随温度的变化.并对组分相同导电类型不同、晶向不同以及结晶状态不同的样品的Seebeck系数进行了比较.在研究温度区间,Seebeck系数的绝对值大小一般在200～600μV/K之间,随温度不同连续变化.通过对比发现SiGe合金的Seebeck系数大小不仅与Ge的浓度和温度有关,其他因素对其绝对值也有影响,其中晶向最为明显,表现出了明显的各向异性.此外,材料本身的电阻率除了作为一个热电参数影响最优值外,其大小还对Seebeck系数的绝对值有影响,即掺杂济浓度对Seebeck系数的影响.     

用化学溶液方法在Ni-5at%W基底上制备La2Zr2O7过渡层的研究

La2Zr2O7(LZO)过渡层以其独特的物理化学性质越来越受到人们的关注。本文以乙酰丙酮镧和乙酰丙酮锆为前驱盐,丙酸为溶剂配置前驱液,用化学溶液方法(CSD)在具有立方织构的Ni-5at%W基底上制备了LZO过渡层薄膜。研究了前驱液成分、性质以及退火温度对LZO成相以及取向的影响。用常规XRD和X射线四环衍射仪分析了LZO薄膜的相成分和织构。结果显示,在1050℃下退火可以获得强立方织构的LZO薄膜,其中(222)峰的Phi扫描半高宽值为8.95°;(400)峰的Chi扫描半高宽值为6.8°。用高分辨扫描电子显微镜(FE-SEM)观察到LZO薄膜表面均匀致密,没有裂纹和空洞。     

磁致伸缩材料弱磁场响应特性的实验研究

针对磁致伸缩材料在弱磁场传感器领域的应用需要,采用迈克耳逊干涉原理实验测量了零应力条件下Tb-Dy-Fe材料和Fe-Ga合金的磁场响应灵敏度,以及不同应力下Fe-Ga合金的磁场响应特性和温度响应特性.实验结果表明：在零应力,外加磁场16 mT条件下,Fe-Ga合金的磁场响应灵敏度远高于Tb-Dy-Fe材料,更合适作为弱磁场传感器敏感材料;同时,在1.2 MPa预应力和26 mT偏置磁场下,Fe-Ga合金材料具有较好的磁场响应灵敏度和较大的饱和磁致伸缩系数,因而处在最佳工作状态.所得到的材料的磁场和温度响应曲线可作为弱磁场传感器参量设计的参考依据.     

连续激光辐照ZnSe/MgF2/K9滤光片的透射特性研究

分析了连续激光辐照ZnSe/MgF2/K9滤光片引起透射特性的变化。在室温条件下,用波长0.632 8μm激光作为探测光束,测量了1.06μm连续激光辐照ZnSe/MgF2/K9滤光片温升引起薄膜折射率的改变,导致探测光束通过干涉滤光片后透过率的热致非线性变化。在光斑直径0.75mm条件下,测量了不同功率激光辐照ZnSe/MgF2/K9滤光片引起温升随时间的变化。在激光功率30W,辐照时间2.52s条件下,实验观测到ZnSe/MgF2/K9滤光片薄膜破坏温度约为90℃,辐照时间10s时干涉滤光片形成的薄膜龟裂形貌。     

高反射膜激光零几率损伤阈值的实验研究

在确定光学薄膜激光损伤阈值的实验数据处理过程中,发现一些样品的数据点分布偏离直线型式。对此,用国际标准规定的零几率来确定损伤阈值的同时,对测试数据点采用了不同的非直线拟合,也得到一个零几率损伤阈值。比较两者差异,并与实验测试结果对照,发现这些样品采用非直线拟合得出的零几率损伤阈值与实际情况更接近一些。     

热处理条件对PVA薄膜阻氢性能的影响

采用XRD测定了PVA薄膜在不同热处理条件下的结晶度,并用自行设计的渗氢系数测量系统研究了在不同热处理条件下的PVA薄膜阻氢性能的变化规律。结果表明,PVA薄膜的热处理温度越高,其结晶度越高,越有利于提高PVA薄膜的阻氢性能,但热处理温度宜选择在180℃以下,以防止PVA薄膜热降解,另一方面,在PVA的玻璃化转变温度以下进行热处理同样能够提高PVA薄膜的阻氢性能,而醇解度较低的PVA薄膜在玻璃化转变温度以下经热处理后的阻氢性能提高的幅度较大。     

电子束、离子辅助和离子束溅射三种工艺对光学薄膜性能的影响

运用电子束、离子辅助和离子束溅射三种镀膜工艺分别制备光学薄膜,包括单层氧化物薄膜和增透膜,然后采取一系列测试手段,如Zygo轮廓仪、原子力显微镜、表面热透镜技术和X射线衍射等技术,来分析和研究不同的工艺对这些薄膜性能的不同影响,以判断合理的沉积工艺。     

Novel Protonic Conductive Silicates Produced by the Sol-Gel Method

ABSTRACT

Materials which display ionic conductivity were produced by the sol-gel and microemulsion-gel methods. The charging and discharging characteristics were investigated and it was found that a single ionic species was responsible for the conduction, the ionic species being residual protons from the initial component mixture. The complex impedence of various samples was measured and the ionic conductivities ranged in value from 9 × 10^?8 to 1 × 10^?5 ohm^?1 cm^?1. An Arrhemius plot for a microemulsion-gel revealed that the energy of activation was 0.15 eV.     

Size-dependent ignition temperature of metallic compounds fabricated by self-propagating high-temperature synthesis

Considering the diffusion reaction at solid interfaces, the ignition temperature of compounds fabricated by self-propagating high-temperature synthesis (SHS) is modelled with the help of size-dependent activation energy. As reactant size decreases, ignition temperature also decreases. This is because of increased contact areas between the reactants and the lowered diffusion barrier, both of which must be calculated specifically for reactants in nanoscale. The model predictions and experimental results are consistent for some metallic compounds.     

Dislocation driven chromium precipitation in Fe-9Cr binary alloy: a positron lifetime study

The influence of initial heat treatment on anomalous Cr precipitation within high temperature solubility region of the Fe–9Cr alloy has been investigated using positron lifetime studies. Air-quenched samples with pre-existing dislocations exhibited a distinct annealing stage in positron lifetime between 800 and 1100?K corresponding to Cr-precipitation. During this stage, Transmission Electron Microscopy showed fine precipitates of average size 4 nm, dispersed throughout the sample and from Energy-dispersive X-ray spectroscopy (EDS) analysis they are found to be Cr-enriched. The presence of dislocations is found to be responsible for Cr precipitation.