Electrochemical synthesis, characterization and some properties of a polymer derived from thioflavin S

Polymeric films derived from thioflavin S were electrosynthesized on mild steel and silver electrodes in sulfuric acid and lithium perchlorate-containing aqueous solutions. The introduction of thioflavin S in an acidic solution protected the surface of steel from corrosion. The electrochemical behavior of the steel coated with a layer of poly(thioflavin) was examined by electrochemical impedance spectroscopy. The films exhibited a capacitive behavior and were semi-conductive in nature. Infra red reflectance measurements of the polymer films at the steel surface showed that the polymer structure retained the aromatic structure of the benzene and thiazole rings with the distinction of a nitrogen quinone vibrational band. Surface morphology of the polymer film was examined with scanning electron microscopy. The films are yellow, compact and dense when electrochemically formed onto steel surfaces when compared to a blue rather porous when formed onto silver electrode. The mechanism of electropolymerization of thioflavin is given and found similar to that of aniline with the possibility of metal chelation with the sulfur and/or nitrogen in the thiazole ring.     

Microcalorimetric studies on the non-competitive inhibition of bovine liver arginase

Two methods, e.g. initial rate method and thermokinetic reduced extent method were presented for studies on non-competitive inhibition. Arginase-catalyzed the hydrolysis of L-arginine toL-ornithine and urea and the inhibition of this reaction by sodium fluoride were studied in the absence and presence of exogenous of Mn²⁺at 37°C in 40 mM sodium barbiturate-hydrochloric acid buffer solution (pH 7.4). Both methods were successively used to determine the values of K₁. The advances and disadvantages of each method were compared in this paper. Exogenous Mn²⁺ could result in more sensitivity of arginase to F^-1. Since the inhibition of arginase by F^-1 depends on the pH values of the reaction system and behave as a non-competitive inhibition, it probably due to its small volume and high electronic density allow it access to the activity site of the enzyme and replaces of μ-OH₂ (or μ-OH) as the bridge ligand with Mn(II, II) cluster. However, further studies are necessary to determine the modes of interaction of F^-1 with bovine liver arginase. This revised version was published online in August 2006 with corrections to the Cover Date.     

Valorization of Zea mays hairs waste extracts for antioxidant and anticorrosive activity of mild steel in 1 M HCl environment

The extraction of Zea mays hairs (Z. mays) was carried out by soxhlet and ultrasound techniques and through three solvents. Phytochemical tests and quantitative analysis of total phenols content (TPC) and flavonoids content (FC) for all extracts were also determined. The antioxidant activity, for different fractions, was determined by using three methods; DPPH, FRAP and TAC. All extracts were rich in polyphenols and the analysis of TPC and FC showed that the hydro-ethanolic extract obtained by ultrasound was characterized by a significant amount of TPC and FC. The n-butanolic fraction was rich in FC and also had a very high antioxidant capacity. On the other hand, the inhibiting effect of hydro-ethanolic extract, n-butanolic fraction and standard (flavone) on mild steel corrosion in 1 M HCl solution was investigated by electrochemical measurements. The polarization curves along with EIS diagrams indicated that flavone was the major molecule responsible for inhibition and acted as mixed-type inhibitor with predominant control of cathodic reaction. The antioxidant activity of BF was well correlated to corrosion inhibition efficiency.     

Reaction kinetics of the selective liquid phase hydrogenation of styrene oxide to β-phenethyl alcohol

Liquid phase hydrogenation of styrene oxide using 1% Pd/C and NaOH as a promoter was found to give selectively β-phenethyl alcohol (PEA) under very mild conditions (313–333 K; 0.68–5.5 MPa). The kinetics of this system was investigated by collecting initial rate data in a batch slurry reactor. Rate of hydrogenation was found to decrease beyond a certain concentration of both hydrogen (>3 MPa) and styrene oxide (>0.5 kmol/m³). A Langmuir–Hinshelwood type rate equation has been proposed based on the initial rate data in the kinetic regime. The model predictions agree very well with the experimentally observed concentration–time data indicating the applicability of the proposed rate model.     

A Systematic Evaluation of Polyurethane as a Conformal Coating for the Inhibition of Corrosion on Electronic Components

The corrosion of printed circuit boards can be effectively prevented with a polyurethane conformal coating. In this study, the protective performance of PU coating was investigated systematically through electrochemical measurements and simulated exposure/immersion tests. Some fungi tests were also included. All experimental results show that a polyurethane coating effectively inhibits corrosion on printed circuit boards. The optimal thickness of the coating film should be about 60 μm. Long-term exposure tests showed that this coating material could preserve the reliability of the investigated printed circuit boards for more than 400 days in a 90% relative humidity environment at 25°C.     

Composition and in vitro Antifungal Activity of Essential Oils of Erigeron canadensis and Myrtus communis from France

Essential oils of Erigeron canadensis L. and Myrtus communis L. were tested in vitro as growth inhibitors against phytopathogenic fungi Rhizoctonia solani Kuhn, Fusarium solani (Mart.) Sacc. and Colletotrichum lindemuthianum (Sacc. & Magn.) Briosi & Cav. Both showed weak fungicidal acitivity, except the essential oil of M. communis that exerted a 60% growth inhibition against R. Solani at a dose of 1600 ppm. Microscopic observation revealed that the essential oil of M. Communis caused morphological alterations of hyphae of all fungi at 1600 ppm, while, at the same dose, only the hyphal morphology of C. Lindemuthianum was affected by the essential oil of Er. Canadensis.     

Preparation and investigation of structural and photocatalytic properties of phosphate modified titanium dioxide

A series of high surface area titanium dioxide samples (P-TiO₂) with varying phosphate content have been prepared by the sol–gel technique. The structural characterization of the samples included X-ray powder diffraction, diffuse reflectance infrared and UV–vis spectroscopy (DRIFT and UV–vis–DR), and nitrogen adsorption measurements. The structural properties of the P-TiO₂ samples significantly changed with the phosphate content and calcination temperature. According to XRD data the presence of phosphate shifts the anatase rutile phase transition to higher temperatures, revealing that phosphate improves the thermal stability of the samples. The specific surface area and the semiconductor band gap energy increase with the phosphate content.

The photocatalytic activity of TiO₂ and P-TiO₂ was studied by phenol degradation in liquid phase. A small amount of phosphate of the catalysts increases the photocatalytic activity, but further increase of the P/Ti molar ratio (above 0.01), leads to a considerable loss in activity. The optimal calcination temperature of P-TiO₂ was 300–500 °C. The phenol conversion rate is highest with catalysts calcined at 700 °C, but phenol does not degrade to carbon dioxide.     

Kinetic parameters of urease immobilized on modified acrylonitrile copolymer membranes in the presence and absence of Cu(II) ions

Poly(acrylonitrile-methylmethacrylate-sodium vinylsulfonate) membranes were subjected to seven different chemical modifications and the amount of the newly formed groups was measured for each membrane. Urease was then covalently immobilized onto the modified membranes and the amount of bound protein was determined. The kinetic parameters V(max) and K(m) of the immobilized urease were studied under static and dynamic conditions. Results showed that the rate of the enzyme reaction was higher for the membranes modified with NH(2)OH . H(2)SO(4), NH(2)NH(2) . H(2)SO(4), NaOH + EDA and NaOH + GA + EDA. It was confirmed that the reaction rate, measured under dynamic conditions, was higher than that one determined under static conditions. The influence of Cu(II) ions, as inhibitors, on the enzyme reaction kinetics (V(i) and K(i)) was also investigated. It turned out that the most sensitive membranes towards Cu(II) were those modified with NH(2)NH(2) . H(2)SO(4), NaOH + EDA and H(2)O(2). The results initiated further investigations on the influence of other heavy metal ions (Cd(II), Zn(II), Ni(II) and Pb(II)) over urease bound to a NH(2)OH . H(2)SO(4)-modified membrane. It was found that the inhibition effect of the heavy metal ions over immobilized urease decreases in the order: Cu(II) > Cd(II) > Zn(II) > Ni(II) > Pb(II). [Diagram: see text]     

Oxygen Inhibition and Coating Thickness Effects on Uv Radiation Curing of Weatherfast Clearcoats Studied by Photo-DSC

Radiation curing is an environmentally-friendly technology. Furthermore, radiation curing is a faster, energy saving and more efficient industrial process than the heat-curable process. One of the most important requirements for the widespread application of UV curable coatings in the coating industry is that they are stable vs. atmospheric degradation. Today's state of the art in oxidative drying and thermosetting coatings is the use of light stabilizers to protect polymers vs. the damage of outdoor exposure. Oxygen has a detrimental effect on the cure response of free radical systems, especially in thin-film coatings. Differential photocalorimetry (photo-DSC) was used to investigate the oxygen effect and the use of light stabilizers on UV curing of photocurable formulations based on acrylate materials. Coating thickness influence was also considered. This revised version was published online in August 2006 with corrections to the Cover Date.     

Ionic liquid–modified cellulosic hydrogels for loading and sustained release of selenourea: an ensuing inhibition of tyrosinase activity

Cellulose-based hydrogel materials were prepared and modified with tannic acid and l-methionine using ionic liquid as the solvent. The gels were prepared to develop a sustained release medium for selenourea (SeU). The drug delivery characteristics of selenourea-loaded cellulose (CSeU), selenourea-loaded tannic acid-modified cellulose (CTSeU), and selenourea-loaded L-methionine-modified cellulose (CMSeU) were investigated in aqueous media and simulated gastric fluid (SGF) media. This modified gel beads have been characterized using field emission scanning electron microscope, X-ray energy-dispersive spectroscopy, Fourier transform infrared spectroscopy, thermogravimetry–differential thermal analysis and swelling properties and compared with those of the unmodified ones. We also investigated the inhibitory effects of SeU released from these gels on the activity of mushroom tyrosinase. Out of all the gel materials, CTSeU showed maximum SeU release both in water and SGF media. However, tyrosinase inhibitory action in PBS medium was comparable for all the three gel materials.