Application of advanced oxidation processes for removing salicylic acid from synthetic wastewaters

<正>In this study,advanced oxidation processes(AOPs) such as anodic oxidation(AO),UV/H_2O_2 and Fenton processes(FP) were investigated for the degradation of salicylic acid(SA) in lab-scale experiments.Boron-doped diamond(BDD) film electrodes using Ta as substrates were employed for AO of SA.In the case of FP and UV/H_2O_2,most favorable experimental conditions were determined for each process and these were used for comparing with AO process.The study showed that the FP was the most effective process under acidic conditions,leading to the highest rate of SA degradation in a very short time interval.However,the results showed that Ta/BDD films had high electrocatalytic activity for complete degradation of SA;even if it employs more time for complete elimination of the SA respect to FP.Additionally,AO led to a sixfold acceleration of the oxidation rate compared with the UV/H_2O_2 process.Finally a rough comparison of the specific energy consumption shows that AO process reduced the energy consumption by at least 90%compared with the UV/H_2O_2 process.     

Effect of phase stability degradation of bismuth on sensor characteristics of nano-bismuth fixed electrode

Effect of phase stability degradation of bismuth on sensor characteristics of nano-bismuth fixed electrode has been investigated using square-wave anodic stripping voltammetry technique, scanning electron microscopy (SEM) and X-ray diffraction (XRD) spectroscopy. From the analyses of square-wave anodic stripping voltammograms (SWASV) repetitively measured on the nano-bismuth fixed electrode, it was found that the oxidation peak currents dropped by 81%, 68% and 59% for zinc, cadmium and lead, respectively, after the 100th measurement (about 400 min of operation time). The sphere bismuth nanoparticles gradually changed to the agglomerates with petal shape as the operation time increased. From the analyses of SEM images and XRD patterns, it is confirmed that the oxidation of Bi into BiOCl/Bi₂O₂CO₃ and the agglomeration of bismuth nanoparticles caused by the phase change decrease a reproducibility of the stripping voltammetric response. Moreover, most of the bismuth becomes BiOCl at pH 3.0 and bismuth hydroxide, Bi(OH)₃ at pH 7.0, which results in a significant decrease in sensitivity of the nano-bismuth fixed electrode.     

Homocysteine Voltammetry at a Mercury Electrode in the Presence of Nickel Ions

At a mercury electrode, Hcy and Cys yield similar cathodic stripping peaks connected to the reduction of the pertinent mercury thiolate. However, due the different behavior as a ligand for nickel ion, the above compounds perform very differently in the presence of this ion. Whereas the nickel ion at a high enough concentration suppresses the Cys peak, in the case of Hcy it causes the cathodic peak to shift to more negative potentials. The peculiar behavior of Hcy is due to the stabilization of the mercury thiolate surface layer by intermolecular Ni²⁺ bridges within the surface layer. Conversely, in the case of Cys, the nickel ion strongly competes with the mercury ion and leads to the formation of a surface adsorbed bis‐cysteinatonickelate complex, which prevents the formation of mercury cysteinate. Such a difference allows determining Hcy by cathodic stripping voltammetry in the presence of nickel ion with no Cys interference.     

Quantification of Sub‐Nanomolar Levels of Aluminum by Adsorptive Stripping Voltammetry Using Rubeanic Acid as a Selective Chelating Agent

A novel, sensitive and selective adsorptive stripping procedure for determination of aluminum is presented. The method is based on the adsorptive accumulation of dithiooxamide (Rubeanic acid) complex of aluminum onto a hanging mercury drop electrode, followed by reduction of adsorbed species by voltammetric scan using differential pulse modulation. The influences of control variables on the sensitivity of the proposed method for the determination of aluminum were studied. The optimum analytical conditions were found to be Rubeanic acid (RA) concentration of 8.0×10^?5 M, ammonia buffer (NH₃? NH₄Cl) pH of 6.5, and accumulation potential at ?50 mV vs. Ag/AgCl with an accumulation time of 60 s. The peak currents are proportional to the concentration of aluminum over the 0.3–70 ng mL^?1 ranges with detection limit of 0.012 ng mL^?1. The procedure was applied to the determination of aluminum in the Lab. Water, HCl of Merck and potato samples with satisfactory results.     

Simultaneous determination of guanine and adenine in DNA using an electrochemically pretreated glassy carbon electrode

A simple and reliable method based on adsorptive stripping at an electrochemically pretreated glassy carbon electrode (GCE) was proposed for simultaneous or individual determination of guanine and adenine in DNA. The detection sensitivity of guanine and adenine was improved greatly by activating the GCE electrochemically. After accumulation on pretreated GCE at open circuit for 5 min or at the potential of +0.3 V for 120 s, guanine and adenine produced well-defined oxidation peaks at about +0.8 and +1.1 V, respectively in pH 5 phosphate buffer. The detection limit for individual measurement of guanine and adenine was 4.5 ng ml⁻¹ (3×10⁻⁸ mol l⁻¹) and 4 ng ml⁻¹ (3×10⁻⁸ mol l⁻¹), respectively. Acid-denatured DNA showed two oxidation peaks corresponding to guanine and adenine residues in the same buffer. The proposed method can be used to estimate the guanine and adenine contents in DNA with good selectivity in a linear range of 0.25-5 μg ml⁻¹.     

Voltammetric Lead Determination in Aviation Fuel Samples Using a Screen‐Printed Gold Electrode and Batch‐Injection Analysis

This work presents the lead determination in aviation (bio)fuels using disposable screen‐printed gold electrodes (SPGEs) adapted on a batch‐injection cell associated with a micropipette for portable analysis. The method involves injections of 200 µL of sample or standard solutions at controlled dispensing rate (4.8 µL s^?1) during deposition step (?550 mV for 90 s), followed by anodic‐stripping voltammetry. Either samples treated by sonication or dry‐ashing can be analyzed with detection limits of 0.0071 and 0.0008 µg g^?1 Pb, respectively. A single SPGE can be applied for 60 consecutive measurements (or 120 for samples dry‐ashed). The ultrasound‐assisted treatment is faster, safer, and easily adapted for on‐site analyses, especially considering the portable characteristics of commercially‐available potentiostats and batch‐injection analysis cell using SPGEs.     

双氯芬酸钠在石墨烯和室温离子液体复合修饰电极上的电化学行为及其测定

运用循环伏安法研究了双氯芬酸钠(DS)在石墨烯(Gene)和室温离子液体1-丁基-3-甲基咪唑六氟磷酸盐(BMIMPF6)复合修饰电极上的电化学行为。DS在该复合电极上于0.65V处有一不可逆氧化峰。在40～200 mV/s范围内,其氧化峰电流与扫描速率平方根(v1/2)呈良好线性关系,表明电极过程是受扩散控制。测定了部分电极过程参数,优化了方波溶出伏安法(SWSV)的实验参数,DS浓度在1.0×10-7～1.0×10-4mol/L范围内与峰电流Ipa呈良好线性关系,检出限为8.0×10-8mol/L(S/N=3),加标回收率为95.7%～101.7%。     

Selective, sensitive and economical method for the adsorptive voltammetric determination of trace amounts of Mo(VI) in organic matter rich environmental samples

A differential pulse adsorptive stripping voltammetric method has been developed for molybdenum trace determination in environmental water samples containing organic compounds. It was proved that interferences from the organic matrix such as surface active substances and humic substances could be removed by the addition of resin to the analysed sample prior to voltammetric measurement. The parameters for Mo(VI) determination in the presence of resin, using a hanging mercury drop as the working electrode, were examined systematically for two complexing agents: cupferron and chloranilic acid. The detection limits estimated from 3 times the standard deviation for a low Mo(VI) concentrations were equal to 5 × 10⁻¹¹ and 3 × 10⁻¹⁰ mol L⁻¹ for cupferron and chloranilic acid, respectively. At the optimized conditions the quantitative Mo(VI) determination in the presence of even 50 mg L⁻¹ of surface active compounds can be performed. The proposed procedures were validated in the course of Mo(VI) determination in certified reference material NASS-5 and in the course of studying recovery of Mo(VI) from spiked river water samples.     

Growth of Anodic Films on Compound Semiconductor Electrodes: InP in Aqueous (NH4)2S

Summary.  Film formation on compound semiconductors under anodic conditions is discussed. The surface properties of InP electrodes were examined following anodization in an (NH₄)₂S electrolyte. The observation of a current peak in the cyclic voltammetric curve was attributed to selective etching of the substrate and a film formation process. AFM images of samples anodized in the sulfide solution revealed surface pitting. Thicker films formed at higher potentials exhibited extensive cracking as observed by optical and electron microscopy, and this was explicitly demonstrated to occur ex situ rather than during the electrochemical treatment. The composition of the thick film was identified as In₂S₃ by EDX and XPS. The measured film thickness varies linearly with the charge passed, and comparison between experimental thickness measurements and theoretical estimates for the thickness indicate a porosity of over 70%. Cracking is attributed to shrinkage during drying of the highly porous film and does not necessarily imply stress in the wet film as grown. During the growth of the thick porous film, spontaneous current oscillations have been observed. The frequency of oscillation was found to be proportional to the current density, regardless of whether the measurements were carried out during a potential sweep or at constant potential. Thus, the charge passed per oscillation remained constant. A characteristic value of approximately 0.3 C · cm⁻² was measured under potential sweep conditions, and a similar value was obtained at constant potential. Received October 16, 2001. Accepted (revised) December 21, 2001     

Determination of Cr(VI) in the presence of Cr(III) and humic acid by cathodic stripping voltammetry

A voltammetric procedure in the flow system for determination of traces of Cr(VI) in the presence of Cr(III) and humic acid is presented. The calibration graph is linear from 5×10⁻¹⁰ to 1×10⁻⁷ mol l⁻¹ for an accumulation time of 120 s. The R.S.D. for 1×10⁻⁸ mol l⁻¹ Cr(VI) is 5.3% (n=5). The detection limit estimated from 3σ for a low concentration of Cr(VI) and accumulation time of 120 s is 2×10⁻¹⁰ mol l⁻¹. The method can be used for Cr(VI) determination in the presence of up to 50 mg l⁻¹ of humic acid. The validation of the method was carried out by studying the recovery of Cr(VI) from spiked river water and by the comparison of the results of determination of Cr(VI) in a soil sample. The method cannot be used for analysis of samples containing high concentrations of chloride ions such as seawater and estuarine water.