Speciation Analysis of Inorganic Tin (Sn(II)/Sn(IV)) by Graphite Furnace Atomic Absorption Spectrometry Following Ion-Exchange Separation

A new method based on anion exchange resin separation and graphite furnace atomic absorption spectrometry (GFAAS) detection is proposed for the determination of inorganic tin species. The result showed that Sn(IV) was quantitatively retained on the resin when [HCl] = 9.0 mol · L⁻¹, but Sn(II) could not be adsorbed on the resin under the same condition. Thus, a separation of Sn(II) and Sn(IV) has been realized. When the concentration of NaOH solution was between 2.0–7.0 mol · L⁻¹, Sn(IV) that adsorbed on the resin could be eluated from the resin completely. Meanwhile, under the atmosphere and the nitrogen states, the translation between Sn(II) and Sn(IV) was investigated. Under the optimal conditions, the detection limit of Sn(IV) is 0.40 μg · L⁻¹ with RSD of 2.3% (n = 5, c = 2.0 μg · L⁻¹). The proposed method was applied to the speciation analysis of tin in different water samples and the recovery of total Sn was in the range of 98.7–101.7%. In order to verify the accuracy of the method, a certified reference water sample was analyzed and the results obtained were in good agreement with the certified value.     

REM树脂的制备及亲核加成应用研究

用Mitsunobu反应及丙烯酰氯酰化反应制备了用于固相有机合成的载体REM树脂，将REM树脂与苄胺加成，考查了所合成REM树脂的反应性能，并通过元素分析测定氮含量，推出REM树脂的烯丙基固载量。利用所合成的REM树脂进行了与胺、酚的加成反应动力学研究。结果表明，REM树脂与脂肪族伯胺和促胺的加成反应能够进行，与苯胺不发生反应；REM树脂与酚不能发生亲核加成反应。     

含氰基的酚醛树脂及其碳纤维复合材料

含氰基的酚醛树脂，具有优异的耐高温性能和高温下的机械强度，在３１５℃下性能变化甚小；不着火，发烟量低，有良好的加工成型性能。热固化过程中氰基成三嗪环而交联，没有小分子脱出，是一类具有广泛发展前景的新型热固性树脂。     

甲基百里(香)酚蓝新负载树脂的特 性及应用

本文以金属指示剂甲基百里(香)酚蓝作为鳌合剂制得具有相应鳌合基团的负载树脂.研究了该树脂的某些分析特性及其在富集天然水中微量铜、钻、镍、锌中的应用.     

Studies on thermal and morphological properties of 1,1-bis(3-methyl-4-cyanatophenyl)cyclohexane-epoxy-bismaleimide matrices

A new cyanate ester monomer, 1,1-bis(3-methyl-4-cyanatophenyl)cyclohexane has been synthesized and characterized. Epoxy modified with 4, 8 and 12% (by weight) of cyanate ester were made using epoxy resin and 1,1-bis(3-methyl-4-cyanatophenyl)cyclohexane and cured by using diaminodiphenylmethane. The cyanate ester modified epoxy matrix systems were further modified with 4, 8 and 12% (by weight) of bismaleimide (N,N′-bismaleimido-4,4′-diphenylmethane). The formation of oxazolidinone and isocyanurate during cure reaction of epoxy and cyanate ester blend was confirmed by IR spectral studies. Bismaleimide-cyanate ester-epoxy matrices were characterized using differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and heat deflection temperature (HDT) analysis. Thermal studies indicate that the introduction of cyanate ester into epoxy resin improves the thermal degradation studies at the expense of glass transition temperature. Whereas the incorporation of bismaleimide into epoxy resin enhances the thermal properties according to its percentage content. However, the introduction of both cyanate ester and bismaleimide influences the thermal properties according to their percentage content. DSC thermogram of cyanate ester modified epoxy and bismaleimide modified epoxy show unimodel reaction exotherms. The thermal degradation temperature and heat distortion temperature of the cured bismaleimide modified epoxy and cyanate ester-epoxy systems increased with increasing bismaleimide content. The morphology of the bismaleimide modified epoxy and cyanate ester-epoxy systems were also studied by scanning electron microscopy. Copyright © 2003 John Wiley & Sons, Ltd.     

Reagent concentration effects in the REM resin solid phase synthesis of tertiary amines

The use of reagent concentration has resulted in increased rates for all stages of the REM resin synthesis of tertiary amines. These increases in rate translate into faster reaction times, higher yields and lower reagent consumption. Of the methods examined, the most successful was the use of perfluorous solvents, either alone or with a small amount of organic co-solvent.     

Studies on the blends of cardanol-based epoxidized novolac resin and CTPB

Cardanol-based novolac-type phenolic resins were synthesized with different mole ratios of cardanol-to-formaldehyde, viz., 1:0.6, 1:0.7, and 1:0.8. These novolac resins were epoxidized with molar excess of epichlorohydrin at 120 °C in basic medium. The epoxidized novolac resins were, separately, blended with different weight ratios of carboxyl-terminated polybutadiene liquid rubber ranging between 0-25 wt% with an interval of 5 wt%. All the blends were cured at 150 °C with 40 wt% polyamide. The formation of various products during the curing of blend samples has been studied by Fourier-transform infra-red spectroscopic analysis. The tensile strength and elongation-at-break of the cured samples increased up to 15 wt% in the blend and decreased thereafter. This blend sample was also found to be most thermally stable system. The blend morphology, studied by scanning electron microscopy analysis, was finally correlated with the structural and property changes in the blends.     

A study of the polymerization of styrene initiated by K-THF-GIC system

In this paper, the polymerization of styrene initiated by potassium (K)-tetrahydrofuran (THF)-graphite intercalation compound (GIC) (K-THF-GIC) was studied. The mechanism of the polymerization was determined to be anionic polymerization according to its characteristics. The effect of the concentration of the initiator and monomer was studied. It was found that the polymerization mainly occurred on the surface and edge of the intercalated graphite. It was also shown that the polarity of solvent has little effect on the polymerization yield in this system.     

纤维素基磁性聚偕胺肟树脂吸附锂

研究了氯化锂浓度、树脂含量和溶液的ＰＨ对碱式纤维素基磁性聚偕胺肟树脂吸附Ｌｉ＾＋离子能力的影响。在适当条件下，每个偕胺肟基可吸附两个Ｌｉ＾＋离子。