Electrolytical production of Ni + Mo + Si composite coatings with enhanced content of Si

Ni + Mo + Si composite coatings were prepared by co-deposition of nickel with molybdenum and silicon powders from a nickel solution in which Mo and Si particles were suspended by stirring. The layers have been deposited on a carbon steel substrate (St3S) under galvanostatic conditions. The content of Si in deposited layers was about 2-5 wt.% depending on deposition current density and the value of electric charge. For comparison Ni + Mo composite coatings were obtained under analogous current conditions. Composite coatings of enhanced Si content (15 wt.%) were deposited from an electrolyte in which 40 g/dm³ of Si covered with electroless plated nickel was dispersed. Deposition current density was equal 0.1 A/cm² and the value of electric charge Q = 500 C/cm². The thickness of the coatings was about 100-300 μm depending on their kind, electric charge and the deposition current density. Surface and cross-section morphology were investigated by scanning electron microscope (SEM). All deposited coatings are characterized by great, developed surface area. No internal stresses causing their cracking were observed. Chemical composition of the layers was determined by X-ray fluorescence spectroscopy (XRF) method and quantitative X-ray analysis (QXRD). It was stated, that the content of molybdenum and silicon in Ni + Mo + Si coatings depends on deposition current density and the amount of the powder in bath. The results of structural investigation of the obtained layers by the X-ray diffraction (XRD) method show, that they consist in crystalline Mo or Mo and Si phases built into Ni matrix. Moreover, Ni + Mo + Si composite coatings were modified by thermal treatment. It has been found that the thermal treatment of Ni + Mo + Si composite coatings caused that the new phases (NiSi, Mo₂Ni₃Si and Ni₆Mo₆C_1.06) were obtained.     

Thermal stability and photoluminescence property of hexagonal MoO3·0.55H2O microrods

The metastable phase of well-faceted, hexagonal, prism-like molybdenum oxide hydrate (MoO₃·0.55H₂O) was successfully synthesized by evaporating molybdic acid solution prepared through cation membrane electrolysis of Na₂MoO₄·2H₂O aqueous solution. The obtained crystals were characterized by X-ray diffraction (XRD), thermogravimetric (TG), scanning electronic microscopy (SEM) and photoluminescence (PL) spectrophotometry. The as-prepared MoO₃·0.55H₂O rods were of 2–4 μm in width and 5–12 μm in length. The MoO₃·0.55H₂O microrods displayed photoluminescence properties at room temperature and were transformed into stable orthorhombic α-MoO₃ after air annealing at 380 °C. Moreover, the influence of temperature factor on the phase transformation process, morphology and photoluminescence properties of MoO₃·0.55H₂O was investigated in detail.     

十六烷基氯化吡啶-水-KI体系浮选分离锑

研究了十六烷基氯化吡啶-水-KI体系分离Sb3+的行为及与一些金属离子分离的条件。结果表明,在一定条件下,Sb3+可与Co2+、Al3+、Zn2+、Ni2+、Fe2+和Mn2+定量分离。     

Tunable magnetic properties of arrays of Fe(1 1 0) nanowires grown on kinetically grooved W(1 1 0) self-organized templates

We report a detailed magnetic study of a new type of self-organized nanowires discussed briefly previously [B. Borca et al., Appl. Phys. Lett. 90 (2007) 142507]. The templates, prepared on sapphire wafers in a kinetically limited regime, consist of uniaxially grooved W(1 1 0) surfaces, with a lateral period here tuned to 15 nm. Fe deposition leads to the formation of (1 1 0) 7 nm-wide wires located at the bottom of the grooves. The effect of capping layers (Mo, Pd, Au, Al) and underlayers (Mo, W) on the magnetic anisotropy of the wires was studied. Significant discrepancies with figures known for thin flat films are evidenced and discussed in terms of step anisotropy and strain-dependent surface anisotropy. Demagnetizing coefficients of cylinders with a triangular isosceles cross-section have also been calculated, to estimate the contribution of dipolar anisotropy. Finally, the dependence of magnetic anisotropy with the interface element was used to tune the blocking temperature of the wires, here from 50 to 200 K.     

极谱法快速检测地球化学勘查样品中的钨和钼

采用质量比3+1的NaOH+KOH混合熔剂熔矿,固定体积的提取溶剂,医用注射器吸取澄清溶液,省去调节酸度过程,一次注射加入极谱底液,催化极谱法测定地球化学勘查样品中的钨和钼。方法检出限为W0.30μg/g、Mo0.49μg/g。方法精密度(RSD,n=12)为W5%—11%、Mo5%—26%。方法准确度(RE,n=12)为W0.5%—18%、Mo1%—31%。     

溶剂浮选-紫外分光光度法分析/富集废水中草甘膦铵盐的研究

基于在酸性条件下,草甘膦铵盐与Fe^3＋可生成稳定配合物,同时以孔雀石绿（MG）作为捕捉剂可提高该配合物在异辛醇等有机溶剂中的溶解度,据此建立了溶剂浮选-紫外分光光度法分析/富集草甘膦生产废水中的草甘膦铵盐的方法。同时考察了捕捉剂和螯合剂及其用量、pH、浮选时间、有机溶剂等因素对浮选效果的影响,并将溶剂浮选法与泡沫浮选法以及溶剂萃取法进行了比较,结果表明溶剂浮选法分离/富集效果最好,草甘膦铵盐回收率达91.2%。     

原子吸收光谱法测定粉煤灰中氧化镁

采用火焰原子吸收光谱法测定粉煤灰中氧化镁的含量。用氢氟酸-高氯酸混合酸分解样品,以氯化锶消除其他元素的干扰。本方法操作简便、再现性好、灵敏度高,氧化镁浓度在0.10—2.00μg/mL之间线性关系良好,检出限可达0.02%,适用于粉煤灰中氧化镁的测定。     

原子吸收光谱法间接测定钼精矿中钼的研究

对于钼精矿中钼的测定,标准方法采用钼酸铅重量法,该方法需要将钼酸铅沉淀反复多次洗涤、过滤,以保证沉淀物中夹带的铅离子洗涤完全,再对沉淀物进行灰化、灼烧等多步操作,步骤较繁琐,分析费时,不能快速配合选矿、冶金的科学研究。应用原子吸收光谱法间接测定钼,建立了钼精矿中钼的快速分析方法。钼精矿样品经硝酸、氯酸钾、硫酸加热溶解后,用酚酞和盐酸调节pH值,加入乙酸-乙酸铵缓冲溶液调节pH值至5～7,再加入一定量且过量的铅标准溶液。基于在室温下,钼酸铅为难溶电解质,难溶电解质在一定温度下能否沉淀完全,通常比较离子积Q_c与溶度积常数K_sp的相对大小,当Q_c>K_sp,溶液过饱和,沉淀物完全析出,钼精矿中钼的含量为40～60%,铅的加入量为0.125 0～0.150 0 g,取最小值计算出溶液中钼酸铅的离子积,Q_c＝[Pb2+][MoO2-₄]=2.51×10-5,K_sp＝1.0×10-13,Q_cK_sp,因此钼酸铅沉淀可以完全析出,待钼酸铅沉淀完全后干过滤,用原子吸收光谱法测定滤液中过量的铅离子,用差减法计算得出钼精矿中钼的含量。文中分别考察了乙酸-乙酸铵缓冲溶液的加入量及其浓度、铅标准溶液的加入量、钼酸铅沉淀完全的时间、加热时间以及常见共存离子如W6+,Sn4+和Cu2+等的最大允许量诸多因素对原子吸收光谱法间接测定钼的影响。与钼酸铅重量法相比,该方法省去了对钼酸铅沉淀反复多次的洗涤、灰化以及灼烧等步骤,操作简便易掌握,分析时间缩短一半,并用钼酸铅重量法与本方法进行对照实验,分析结果进行数理统计,得出结论：本方法具有很好的准确度和精密度,可用于选矿、冶金钼精矿样品中钼的快速分析检测。     

N2 Laser Excited Fluorescence of Oxalyl Chloride at 77°K

The N₂ laser excited fluorescence spectrum and the intensity of fluorescence of oxalyl chloride C₂O₂Cl₂) condensed at 77°K either alone, or, diluted with a non-hydrocarbon or a hydrocarbon with dilution ratios ranging from 10 to 100 were studied. A slow condensation of the hydrocarbon matrix diluted sample showed a considerable reduction in the fluorescence intensity as compared to a fast condensation of the same sample.     

Study on the surface erosion route to the fabrication of TiO2 hollow spheres

Three-dimensional (3D) architecture of TiO₂ hollow sphere has many excellent and interesting performances that attract significant attention nowadays. In this paper, a simple surface erosion approach to the fabrication of TiO₂ hollow spheres via the hydrothermal process has been developed. The morphologies and the phase were characterized by scanning electron microscopy (SEM) and X-ray diffractometer (XRD). The results indicate that the anatase-type TiO₂ hollow spheres with a diameter of ∼1 μm are successfully synthesized. The shell thickness of TiO₂ hollow spheres is ∼150 nm and the size of hollow cavity is ∼600 nm. By the control experiments, the influence of ammonium fluoride and hydrogen peroxide on the hollow spherical structures was studied. Hydrogen peroxide acts as both the oxidant and the bubble generator, ammonium fluoride is crucial for the erosion and dissolution of titanium, the detailed dissolution-crystallization mechanism for the formation of TiO₂ hollow spheres was also proposed.