Physical aging of a polyetherimide: Creep and DSC measurements

Creep and differential scanning calorimetry (DSC) measurements have been used to study the physical aging behavior of a polyetherimide. Isothermal aging temperatures ranged from 160°C to T_g with aging times ranging from 10 min to 8 days. The only measurable effect of physical aging on the short-time creep curves is a shift of the creep compliance to longer times. Andrade plots of the compliance versus the cube root of time are linear at short times with the slope β decreasing with increasing aging time to a constant value once equilibrium is reached. Log β³ is related directly to the degree to which the creep curves shift to longer times with physical aging, and is used in this work as a measure of physical aging. A reduced curve of log β³ versus log aging time is obtained for the aging temperatures investigated by appropriate vertical and horizontal shifts. The enthalpy change during aging increases linearly with the logarithm of the aging time, t_a, leveling off at equilibrium at values which increase with decreasing aging temperature. Hence, both nonequilibrium and equilibrium temperature shift factors can be calculated from the DSC data. Good agreement is observed between the equilibrium temperature shift factors obtained from the creep and DSC data. The temperature dependence of the nonequilibrium temperature shift factors is found to be an order of magnitude smaller than that of the equilibrium shift factors. The time scales to reach equilibrium for enthalpy and for mechanical measurements are found to be the same within experimental error. © 1995 John Wiley & Sons, Inc.     

Elevation of the glass transition temperature in flexible‐chain semicrystalline polymers

In the idealized two‐phase model of a semicrystalline polymer, the amorphous intercrystalline layers are considered to have the same properties as the fully‐amorphous polymer. In reality, these thin intercrystalline layers can be substantially influenced by the presence of the crystals, as individual polymer molecules traverse both crystalline and amorphous phases. In polymers with rigid backbone units, such as poly(etheretherketone), PEEK, previous work has shown this coupling to be particularly severe; the glass transition temperature (T_g) can be elevated by tens of degrees celsius, with the magnitude of the elevation correlating directly with the thinness of the amorphous layer. However, this connection has not been explored for flexible‐chain polymers, such as those formed from vinyl‐type monomers. Here, we examine T_g in both isotactic polystyrene (iPS) and syndiotactic polystyrene (sPS), crystallized under conditions that produce a range of amorphous layer thicknesses. T_g is indeed shown to be elevated relative to fully‐amorphous iPS and sPS, by an amount that correlates with the thinness of the amorphous layer; the magnitude of the effect is severalfold less than that in PEEK, consistent with the minimum lengths of polymer chain required to make a fold in the different cases. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1198–1204, 2007     

Molecular modeling study on surface,thermal, mechanical and gas diffusion properties of chitosan

The motivation of this work is to provide reliable and accurate modeling studies of the physical (surface, thermal, mechanical and gas diffusion) properties of chitosan (CS) polymer. Our computational efforts have been devoted to make a comparison of the structural bulk properties of CS with similar type of polymers such as chitin and cellulose through cohesive energy density, solubility parameter, hydrogen bonding, and free volume distribution calculations. Atomistic modeling on CS polymer using molecular mechanics (MM) and molecular dynamics (MD) simulations has been carried out in three dimensionally periodic and effective two dimensionally periodic condensed phases. From the equilibrated structures, surface energies were computed. The equilibrium structure of the films shows an interior region of mass density close to the value in the bulk state. Various components of energetic interactions have been examined in detail to acquire a better insight into the interactions between bulk structure and the film surface. MD simulation (NPT ensemble) has also been used to obtain polymer specific volume as a function of temperature. It is demonstrated that these V–T curves can be used to locate the volumetric glass transition temperature (T_g) reliably. The mechanical properties of CS have been obtained using the strain deformation method. Diffusion coefficients of O₂, N₂, and CO₂ gas molecules at 300 K in CS have been estimated. The calculated properties of CS are comparable with the experimental values reported in the literature. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1260–1270, 2007     

Effect of nanotube functionalization on the properties of single‐walled carbon nanotube/polyurethane composites

A commercially available aliphatic thermoplastic polyurethane formulated with a methylene bis(cyclohexyl) diisocyanate hard segment and a poly(tetramethylene oxide) soft segment and chain‐extended with 1,4‐butanediol was dissolved in dimethylformamide and mixed with dispersed single‐walled carbon nanotubes. The properties of composites made with unfunctionalized nanotubes were compared with the properties of composites made with nanotubes functionalized to contain hydroxyl groups. Functionalization almost eliminated the conductivity of the tubes according to the conductivity of the composites above the percolation threshold. In most cases, functionalized and unfunctionalized tubes yielded composites with statistically identical mechanical properties. However, composites made with functionalized tubes did have a slightly higher modulus in the rubbery plateau region at higher nanotube fractions. Small‐angle X‐ray scattering patterns indicated that the dispersion reached a plateau in the unfunctionalized composites that was consistent with the plateau in the rubbery plateau region. The room‐temperature modulus and tensile strength increase was proportionally higher than almost all increases seen previously in thermoplastic polyurethanes; however, the increase was still an order of magnitude below what has been reported for the best nanotube–polymer systems. Nanotube addition increased the hard‐segment glass transition temperature slightly, whereas the soft‐segment glass transition was so diffuse that no conclusions could be drawn. Unfunctionalized tubes suppressed the crystallization of the hard segment; whereas functionalized tubes had no effect. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 490–501, 2007     

Thickness dependence of free‐standing thin films

Below a critical thickness, of about 60 nm, the glass transition temperature of polystyrene (PS) films decreases with film thickness, as demonstrated using free‐standing films. A geometrical model is developed here describing this phenomenon in the case of ideal (Gaussian) chains. This model, which can be considered as an application of the free volume model, assumes that the decrease of the glass transition temperature from thick to ultrathin films is due to the modification of the interpenetration between neighboring chains. The theoretical curve deduced from the model is in excellent agreement with the PS experimental results, without using any adjustable parameters. From these results, it can be concluded that new chain motions, usually buried in bulk samples, are expressed by the presence of the surface. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 10–17, 2007     

Optical properties of a high-efficiency glass ceramic X-ray storage phosphor

The turbidity, photoluminescence, and photo-stimulated luminescence (PSL) of fluorozirconate glass containing barium chloride nano- and micro-crystals have been measured for samples prepared by isochronal (70 min) annealing over a temperature range of 220–283°C, and correlated with the microstructure as determined by X-ray diffraction measurements. Crystallization of hexagonal phase barium chloride commences at around 220°C, but until 275°C the material retains excellent transparency although it displays negligible PSL. Between 275°C and 277°C, the hexagonal phase converts to the orthorhombic phase, the transparency abruptly decreases, and the PSL rises to a value of around 13% of that found for the commercial storage phosphor BaFBr:Eu. For a slightly higher temperature of 280°C, new phases appear which correspond to the onset of bulk crystallization, and at 283°C the relative PSL rises to 33%, while the transparency falls further. The trade-off between optical transparency and PSL over this narrow temperature window for X-ray imaging plate applications is briefly discussed.     

扫描力显微术在高聚物薄膜玻璃化转变研究中的应用

简述了高聚物薄膜玻璃化转变的复杂性，并结合文章作者的的一些研究结果介绍了扫描力显微术(SFM)在研究高聚物玻璃化转变中的一些方法，包括观察高聚物薄膜形貌的变化，测量其摩擦力、粘附力和弹性模量等物理量的变化，最后指出SFM是研究高聚物薄膜玻璃化转变的有力工具。     

磁光玻璃光纤的偏振特性及其在全光纤电流传感器中的应用

在磁光玻璃裸光纤偏振特性研究的基础上，研制磁光玻璃光纤，偏振特性及其在全光纤电流传感器中的应用。将采用模管法拉制成的磁光玻璃光纤置于亥姆霍兹线圈产生的磁场中，当线偏振光通过该光纤时，其偏振面旋转一定角度，把该角度转换成光信号的强度，然后再用仪器进行检测。通过对线偏振光偏振面在磁场中的偏振特性的测试与实验，提出用磁光玻璃光纤构成的全光纤电流传感器，可用于电流和磁场测试。     

Determination of the rheological behavior of epoxy–amine thermosets by dynamic mechanical analysis: Isothermal methods versus nonisothermal methods

The reticulation process of an epoxy resin using an amine as a cure agent was studied at different temperatures and concentrations of the cure agent with dynamic mechanical thermal analysis. The study was performed under both isothermal and nonisothermal conditions, and a temperature–time–transformation diagram was obtained. The measurements from the two modes gave similar results, although the nonisothermal mode required fewer experiments. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1965–1977, 2003     

Thiol–norbornene materials: Approaches to develop high Tg thiol–ene polymers

The ability to prepare high T_g low shrinkage thiol–ene materials is attractive for applications such as coatings and dental restoratives. However, thiol and nonacrylated vinyl materials typically consist of a flexible backbone, limiting the utility of these polymers. Hence, it is of importance to synthesize and investigate thiol and vinyl materials of varying backbone chemistry and stiffness. Here, we investigate the effect of backbone chemistry and functionality of norbornene resins on polymerization kinetics and glass transition temperature (T_g) for several thiol–norbornene materials. Results indicate that T_gs as high as 94 °C are achievable in thiol–norbornene resins of appropriately controlled chemistry. Furthermore, both the backbone chemistry and the norbornene moiety are important factors in the development of high T_g materials. In particular, as much as a 70 °C increase in T_g was observed in a norbornene–thiol specimen when compared with a sample prepared using allyl ether monomer of analogous backbone chemistry. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5686–5696, 2007