Evaluation of PLE exhaustiveness for the extraction of PCBs from sediments and the influence of sediment characteristics

Pressurized liquid extractions were performed on eight sediments in order to investigate if a modified US EPA method (100 °C, 100 bar, n-heptane/acetone (1:1), 2 × 5 min) provided exhaustive extractions of polychlorinated biphenyls (PCBs) from sediment, and to study if the extractability of PCBs from the different sediments was affected by characteristics of the sediment. The recovery from the eight native sediments, contaminated in nature, was between 96.4% and 98.9%, as an average of the recoveries from 10 PCB congeners. Hundred percent recovery was defined as the sum of two consecutive extractions (2 × 5 min each) at the stated conditions. The recoveries of the individual congeners were above 94%, except for one congener in one sediment, which had a recovery of 92%. When the recoveries and different characteristics of the sediments were compared, no correlation appeared between recoveries and sediment PCB concentration, total organic carbon (TOC), soot carbon (SC) or amorphous carbon (AC). The fact that carbon did not influence the extractions was somewhat surprising, since previous experiments have indicated a connection. Instead, statistically significant (p < 0.05) correlations were observed for water content and carbon/nitrogen (C/N) ratio. The decrease in recoveries with decreased water content was attributed to less access of the solvent to the analytes due to less matrix swelling. The lowered recoveries with increased C/N ratio can indicate that a difference in structure of the organic matter exists, which influences the binding strength between the analytes and the matrix. The difference in structure can possibly be explained by different origin of the organic matter or by aging effects. Overall the method was found to be exhaustive and the excellent recoveries show that sediment characteristics do not influence the extractions markedly.     

输入输出共轴的三弯曲型TM01-TE11模式转换器

 通过采用相位重匹配技术，设计了一种输入输出共轴的三弯曲型TM₀₁-TE₁₁模式转换器，该转换器由三段常曲率弯曲波导和两段直波导组成。用模式耦合理论建立了该类模式转换器的数值计算和优化设计方法，并设计了一个中心频率为7.0 GHz的模式转换器。该转换器的TM₀₁-TE₁₁转换效率在中心频率上大于99％，在6.5~7.5 GHz的频率范围内大于90％。应用时域有限差分法和有限元方法对所设计的模式转换器进行了仿真，仿真结果验证了设计理论和设计结果。     

微型热驱动热声热机热端换热器的优化设计

该文基于热声环境,采用厘米级扁管和deltaE数值计算对微型热声换热器进行了优化设计。     

外加电场下激光诱导Al等离子体特性的实验研究

由Q-Nd:YAG脉冲激光(波长1.06μm,脉宽10 ns)烧蚀Al靶产生等离子体.观测了在低气压和直流电场条件下的Al等离子体发射光谱.研究了激光功率密度和直流电场对各谱线强度的影响,分析了谱线半高全宽与外加电压,等离子体电子温度与激光能量的变化规律.结果表明,直流电场对铝原子谱线强度有显著的增强,铝原子谱线的半高全宽与直流电场的外加电压基本上呈线性关系.     

Ab initio predictions of zeolite structures and Si NMR chemical shifts

A recent shell-model potential parameterized on ab initio data is used for predicting the all-silica structures of zeolites MFI, MEI, MTW, TON, FAU and of α-quartz. Cluster models are defined around each site and the ²⁹Si NMR shielding constants are calculated by ab initio techniques (GIAO-HF). Good agreement with observed ²⁹Si NMR chemical shifts is found. Comparison is made with shifts calculated for observed structures. The structures predicted by the ab initio shell-model potential prove as accurate as the observed ones when judged on the quality of the calculated ²⁹Si NMR spectra.     

Mössbauer spectroscopy study of spin structure and its in-field and temperature dynamics in B2 ordered Fe(Al) alloys

The experimental data from Mössbauer spectroscopy and magnetic measurements are presented as functions of the temperature and external magnetic field for a B2-type ordered Fe ₆₆ Al ₃₄ alloy.     

Amorphous Fe–Mg alloy thin films: magnetic properties and atomic vibrational dynamics

Amorphous (a-) Fe _x Mg_1?x alloys are interesting materials for the investigation of non-Debye-like low-energy vibrational excitations. We have prepared a-Fe _x Mg_1?x alloy thin films (0.3 ≤ × ≤0.7) by vapour quenching. The amorphous state was confirmed by conversion electron Mössbauer spectroscopy between 4.2–300 K, and the x- and temperature-dependence of the isomer shift and hyperfine magnetic field was measured. For x= 0.6 and 0.7, magnetic ordering occurs below ~150 K. The atomic vibrational density of states, g(E), was determined by nuclear resonant inelastic scattering, providing clear evidence for the non-Debye-like low-energy vibrational excitations.     

Chromatographic characterization of thermally upgraded products from alternative fuels

An overview is presented of the analytical approaches developed by our research group over the last ten years for analysis of alternative fuel, both biomass and fossil. The alternative fuels are analyzed successively by PLC-8 (preparative liquid chromatography–group-type) fractionation and high resolution gas chromatography. Some of the possibilities for fractionation and characterization of alternative fuels are herein exemplified with sugar cane bagasse pyrolysis products.     

Towards understanding the increase in strength of thermotropic polyesters with heat treatment

Thermotropic copolyester fibers of oxynaphthoate and oxybenzoate have been subjected to conditions that promote solid-state polymerization as well as annealing. The annealing process causes the crystals to perfect with a simultaneous increase in heat of fusion and melting temperature. Solid-state polymerization, a reaction rate-controlled process, causes the polymer viscosity average molecular weight to increase by chain extension from about 14,000 g/mole to more than 87,000 g/mole with a simultaneous impressive increase in tenacity from about 10 g/d (1.2 GPa) to almost 30 g/d (3.7 GPa). To understand the changes in mechanical properties, we have modeled the fiber structure as short rod-like molecules poorly bonded to a continuous matrix of parallel molecules. Lengthening of the reinforcing molecules facilitates better transfer of load from matrix to molecules, resulting in higher tenacity fibers. © 1994 John Wiley & Sons, Inc.