Classical versus Jennings model for the ground state of H near a metallic surface

We show that, contrary to earlier reports, application of the one-parameter variational technique to the classical (image) model for H in front of an Al surface leads to energy shifts for the ground state which are very close to those obtained numerically with a more sophisticated model of the system.     

锰结核中硅,铝,铁,镁,磷,钾,锰,钛的XRFA

本文叙述了用XRF分析锰结核中Si、Al、Fe、Mg、P、K、Mn和Ti的方法。按照通常锰结核的主次成分制备6个人工合成标准,根据Sherman方程计算了已知成分(二元系统)的相对强度。用L-T方求得了互致元素校正的理论α系数(基本的、混合的、修正的),用DATAFLEX151B计算机以BASIC语言汇了“PRA,APU”计算机程序。然后进行非线性回归分析了锰结核样品得到了满意的结果。     

Influence of SiO2 in SiCp on the microstructure and impact strength of Al/SiCp composites fabricated by pressureless infiltration

The effect of SiO₂ in SiC_p and the following processing parameters on the microstructure and impact strength of Al/SiC_p composites fabricated by pressureless infiltration was investigated: Mg content in the aluminum alloy, SiC particle size, and holding time. Preforms of SiC_p in the form of rectangular bars (10 × 1 × 1 cm) were infiltrated at 1150°C in an argon→nitrogen atmosphere for 45 and 60 min by utilizing two aluminum alloys (Al-6 Mg-11 Si and Al-9 Mg-11 Si, wt.%). The results obtained show that the presence of SiO₂ in SiC affects the microstructure and impact strength of the composites significantly. When Al₄C₃ is formed, the impact strength decreases. However, a high proportion of SiC to SiO₂ limits the formation of the unwanted Al₄C₃ phase in the composites. Also, a higher content of Mg in the Al alloy lowers the residual porosity and, consequently, increases the composite strength. The impact strength grows with decrease in SiC particle size and increases considerably when the residual porosity is less than 1%. Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 42, No. 3, pp. 401–418, May–June, 2006.     

Microstructure of laser melted Al18B4O33w/2024Al composite

The microstructure of a laser treated Al₁₈B₄O₃₃w/2024Al composite has been investigated using transmission electron microscope (TEM), low-angle (glancing angle) X-ray diffraction (XRD) techniques. Various surface microstructures were observed in the laser treated composite. The Al₁₈B₄O₃₃ whisker on the surface of the composite was decomposed during laser surface melting, various decomposition products were studied in the laser treated composite. Eutectic phases and the precipitation in the matrix of the composite with laser-treated were observed. The main phases detected in the molten zone were aluminum and decomposition products Al₂O₃. The effect of laser treatment on the hardness of the composite was also examined. A surface hardness of 400 Hv was noted.     

Recycling in telomerization of butadiene with D‐xylose: Pd(TPPTS)n‐KF/Al2O3 as an active catalyst

A palladium‐TPPTS catalyst heterogenized on KF/alumina has been shown to be effective and recyclable for the selective formation of monooctadienylxylopyranosides via the telomerization of butadiene with D ‐xylose. Copyright © 2007 John Wiley & Sons, Ltd.     

Structure and mechanical properties of Al/AlN multilayer with different AlN layer thickness

Nanometer scale Al/AlN multilayers have been prepared by dc magnetron sputtering technique with a columnar target. A set of Al/AlN multilayers with the Al layer thickness of 2.9 nm and the AlN layer thickness variation from 1.13 to 6.81 nm were determined. Low angle X-ray diffraction (LAXRD) was used to analyze the layered structure of multilayers. The phase structure of the coatings was investigated with grazing angle XRD (GAXRD). Mechanical properties of these multilayers were thoroughly studied using a nanoindentation and ball-on-disk micro-tribometer. It was found that the multilayer hardness and reduced modulus showed no strong dependence on the AlN layer thickness. Al2.9 nm/AlN1.13 nm multilayer had more excellent tribological properties than single layers and other proportion multilayers with a lowest friction coefficient of 0.15. And the tribological properties of all the multilayers are superior to the AlN single layer.     

26Al的加速器质谱测量及其应用

26Al是一个在多个学科都非常有意义的放射性核素。主要介绍了国内外在利用加速器质谱技术测量26Al时所开展的各种测量方法、各自的优缺点和测量灵敏度，并介绍了目前利用^26Al在地球科学、生物医学、核物理以及天体物理等诸多方面的应用研究工作。     

CuX(X=Al, Ga, In)分子的势能函数与稳定性的密度泛函研究

根据原子分子反应静力学原理导出了CuX(X=Al,Ga,In) 分子基态电子状态及其离解极限,并在B3LYP/LANL2DZ水平上计算了平衡几何、振动频率和解离能.利用Murrell-Sorbie 函数拟合出了解析势能函数,并计算出光谱参数和力常数.计算结果表明该分子体系是稳定存在的,其稳定性排序为 CuAl＞CuGa＞CuIn.     

微型热驱动热声热机热端换热器的优化设计

该文基于热声环境,采用厘米级扁管和deltaE数值计算对微型热声换热器进行了优化设计。     

Enthalpies of sorption of linear hydrocarbons (C2–C8) and chloroderivatives of methane and ethylene on the surface of hydrotalcite

Differential molar adsorption enthalpies (DMAE) were determined by gas chromatographic measurements of specific retention volume of vapors on the surface of two forms of Mg–Al hydrotalcite. A linear dependence of the DMAE on the number of the carbon atoms in hydrocarbons was observed for both form of hydrotalcite. The dependence of the differential molar adsorption enthalpies on the number of chlorine atoms in organic molecules is discussed. A linear dependence of DMAE on the molecular weight of chloroderivatives of methane and ethylene on the basic form in an order monochloromethane < dichloromethane < trichloromethane or vinylidene chloride < 1,1-dichloroethylene < trichloroethylene was found.