乙基苯乙烯与二乙烯苯球形共聚物吸附树脂作反相薄层色谱固定相

本文合成了乙基苯乙烯与二乙烯苯球形共聚物PED－9吸附树脂，粒径3～7μm，用作薄层色谱固定相，对板效进行了研究，并通过分离实例说明它对硝基苯酚及芳胺具有优良的分离性能。     

Preconcentration and Separation Procedures for the Spectrochemical Determination of Platinum and Palladium

Low concentrations of Pt and Pd in industrial (µgg^–1 level) and environmental samples (ngg^–1 level) together with the complexity of the matrix causing many interferences during the determination of noble metals often require elaboration and application of pre-concentration/matrix separation procedures before detection of the analyte. Different pre-concentration/matrix separation procedures applied prior to the determination of Pt and Pd by atomic spectrometric techniques are reviewed and critically compared taking into account potential interferences. The methods studied are divided into 5 groups including precipitation and coprecipitation, liquid–liquid extraction, solid phase extraction, electrochemical pre-concentration and biosorption. The main analytical problems occuring during sample preparation and storage are discussed.     

Use of x-ray microtomography to visualise dynamic adsorption of organic vapour and water vapour on activated carbon

X-ray microtomography coupled with image analysis was used to quantify the adsorption of vapours on activated carbon beds. This technique was tested using three different challenges: CCl₄, water vapour and a mixture of water- and organic vapour. It is shown that the used technique allows determining the adsorption front progress in the case of organic vapour and mixture of water and organic vapour whereas the existence of this front was not so obvious in the case of water vapour. Experimental results obtained for organic vapours were interpreted on the basis of the Wheeler-Jonas equation: a good agreement was found between experimental and theoretical breakthrough times.     

Surface properties of Reactive Yellow 2 immobilised pHEMA and HEMA/chitosan membranes: characterisation of their selectivity to different proteins

Poly(hydroxyethyl methacrylate), pHEMA, and a composite pHEMA/chitosan networks were synthesized in the membrane form via UV initiated photo-polymerisation in the presence of an initiator ,′-azoisobutyronitrile. Reactive Yellow 2 (RY-2) was covalently immobilised as a dye–ligand onto both membranes. The polarity and surface energy of the investigated membranes were determined by contact angle measurement. The incorporation of chitosan in the pHEMA networks produced more hydrophilic surface, as indicated by contact angle analysis. The binding characteristics of lysozyme, γ-globulins, human serum albumin (HSA) and bovine serum albumin (BSA) to pHEMA-RY-2 and pHEMA/chitosan-RY-2 affinity membranes have been investigated from aqueous solution and their dye–ligand free forms were used as control systems. When chitosan was incorporated in the pHEMA network as a cationic polymer led to higher adsorption capacity for the lysozyme. Selective adsorption behaviour was also observed in the case of pHEMA/chitosan-RY-2 membrane for the lysozyme. The non-specific adsorptions of the lysozyme on the pHEMA and pHEMA/chitosan membranes were about 1.9 and 7.2 mg/ml, respectively. These were negligible for all others investigated proteins. The lysozyme adsorption data was analysed using the first-order and the second-order models. The first-order equation in both affinity membrane systems is the most appropriate equation to predict the adsorption capacities of the adsorbents. The adsorption isotherms well fitted the combined Langmuir–Freundlich model. A theoretical analysis has been conducted to estimate the thermodynamic contributions (changes in enthalpy, entropy and Gibbs free energy) for the adsorption of lysozyme to both dye–ligand immobilised membranes. The adsorption capacities of both dye–ligand immobilised membranes increased with increasing the temperature while decreased with increasing the NaCl concentration. Both affinity membranes are stable when subjected to sanitization with sodium hydroxide after repeated separation–elution cycles.     

Retention, kinetics and thermodynamics profile of cadmium adsorption from iodide medium onto polyurethane foam and its separation from zinc bulk

The sorption behaviour of 2.5 × 10⁻⁵ M solution of Cd(II) on polyurethane foam (PUF) from iodide medium have been investigated. The conditions were optimized from aqueous solutions of different pH (1-10) and of acids of varied concentration (0.01-1.0 M). The maximum concentration of KI was found to be 0.24 M and equilibration time was established to be 20 min. The data successfully followed the Freundlich and Dubinin-Radushkevich (D-R) isotherms at low metal ion concentration while Langmuir isotherm followed at higher metal ion concentration. The Freundlich parameter 1/n = 0.66 ± 0.02 have been evaluated whereas D-R isotherm yields the sorption free energy E = 10.5 ± 0.1 kJ mol⁻¹ indicating ion exchange type chemisorption. The monolayer coverage (XL) constant of Langmuir isotherm was found to be 23.7 ± 0.4 mg g⁻¹. The numerical values of thermodynamics parameters enthalpy (ΔH), entropy (ΔS) and Gibbs free energy (ΔG) indicated the endothermic and spontaneous nature of sorption. The Scatchard plot analysis was tested to evaluate the binding sites of the PUF and stability constants of sorption were determined. On the basis of these parameters, the sorption mechanism was discussed. Among the foreign ions tested, Pb(II), Hg(II), cyanide and nitrite should be absent. The clean separation of Cd(II) from Zn(II) ions in the ratio 1:250, respectively, was achieved by column chromatography.     

Effect of surfactants on the stability of thin liquid film flow on a rotating disk

The effect of surfactants on surface instabilities of thin liquid film flow on a rotating disk was studied at different flow rates Q (0.5相似文献   

Evaluation of the adsorption affinity of proteins to calcium hydroxyapatites by desorption and pre-adsorption methods

The adsorption affinity of bovine serum albumin (BSA) and lysozyme (LSZ) to calcium hydroxyapatite (CaHAP) was evaluated by desorption and two step adsorption methods. These experiments were carried out at 15°C in a 1×10⁻⁴ mol dm⁻³ KCl solution of pH 6.0. BSA molecules were scarcely desorbed, exhibiting an irreversible adsorption of BSA, though LSZ slightly desorbed. This result supports our previous findings that LSZ adsorbs weakly onto phosphate ions exposed on ac or bc faces of CaHAP while BSA adsorbs strongly onto positively charged sites on ac or bc faces of CaHAP. The amount of adsorbed LSZ was markedly increased by the pre-adsorption of BSA, where LSZ was adsorbed onto BSA-covered CaHAP. On the other hand, the amount of adsorbed BSA was not changed by the pre-adsorption of LSZ. In both pre-adsorption systems it was confirmed by an HPLC method that no protein molecule pre-adsorbed was desorbed after the post-adsorption procedure. Therefore, it was interpreted that the enhancement of adsorption of positively charged LSZ is induced by an electrostatic attractive force through pre-adsorption of negatively charged BSA molecules with a high coverage. However, since the coverage of LSZ onto CaHAP is considerably low, no stimulation of BSA adsorption occurred on the LSZ-covered surface. The formation of double protein adsorbed layers consisting of pre- and post-adsorbed proteins was proposed.     

Preparation of crosslinked polystyrene-supported ethylenediamine via a S-containing spacer and adsorption properties towards metal ions

Two novel chelating resins were prepared by anchoring ethylenediamine to crosslinked polystyrene via a spacer containing sulfide. Their structures were characterized by Fourier transform-infrared spectra (FTIR) and scanning electron microscopy (SEM). Porous structure parameters of the resins were measured by ASAP 2020 using BET and BJH methods. Their adsorption capacities for several heavy metal ions especially Hg²⁺ were investigated. The results showed that for the two resins, the more N contents did not mean the better adsorption capacity and the saturated adsorption capacity of poly(2-ethylenediamidomercaptomethylstyrene) (PSM-EDA) for Hg²⁺ could reach to 3.0 mmol/g at room temperature. Isothermal adsorptions of the resins for Hg²⁺ could be described by Langmuir formula. The adsorption mechanism of the resins for Hg²⁺, Cu²⁺ and Ag⁺ was confirmed by X-ray photoelectron spectroscopy (XPS) and FTIR.     

Effect of Artabotrys odoratissimus extract as an environmentally sustainable inhibitor for mild steel corrosion in 0.5 M H2SO4 media

Artabotrys odoratissimus inhibitory effect on mild steel (MS) corrosion in 0.5 M H₂SO₄ solution has been assessed utilizing mass loss, electrochemical potentiodynamic polarization, and impedance spectroscopy techniques. The Artabotrys odoratissimus plant has a wide range of bioactive compounds. Phytochemicals were tested for ethanolic Artabotrys odoratissimus leaves extract (AOLE) using the FeCl₃ test, Salkowaski's test, and others. Corrosion tests were conducted at varying inhibitor concentrations and temperatures. The inhibitory impact of AOLE on corrosion of MS was reported to improve with increasing concentration. Polarization experiments revealed that AOLE is a mixed kind of inhibitor and the inhibition efficacy (η_w) for MS is 93.27% for 1.25 g/L AOLE. For Electrochemical impedance spectroscopy (EIS), maximal inhibitory efficacy (η_w) was 91.62% due to AOLE adsorption on the MS surface. The obtained results using each methodology are highly consistent and closely resemble each other. The adsorption of AOLE molecules on an MS surface from the bulk of the solution causes the inhibitor's inhibition action, and the adsorption mechanism follows Langmuir adsorption isotherm. The computed $\Delta G_{ads}^o$ values ranged between ?32.919 and ?33.520 kJ mol^?1, implying a spontaneous and exothermic inhibitory action. The thermodynamic and activation parameters are often used to understand corrosion inhibition mechanisms. The comparison of corrosion product and pure extract FT-IR spectrum indicates the nature of AOLE adsorption on the MS surface. The surface morphology of MS samples was assessed using atomic force microscopy (AFM), scanning electron microscope (SEM), and contact angle techniques.     

MCM-41分子筛负载钼钴系催化剂的噻吩HDS研究

通过氧吸附量、噻吩吸附热及反应速率常数的测定，研究了MoO3/MCM-41、MoO3-CoO(NiO)/MCM-41系列催化剂，发现，对于MoO3/MCM-41催化剂，当MoO3的质量分数（以MCM－41为底数，即MCM－41＝1g时，MoO3含量为0．15g，下同）从15％增加到20％时，其噻吩的加氢硫（HDS）活性增大，至25％时活性下降，所对应的氧吸附量（mL/g催化剂）也是先增大后减少，并且两者有很好的线性对应关系，而且噻吩吸附热则基本保持不变，采用不同的MoO3-CoO(NiO)浸渍顺序制备的MoO3-CoO(NiO)/MCM-41催化剂中，先浸渍CoO(NiO）再浸渍MoO3的催化剂，其噻吩HDS活性明显优于对其它浸渍顺序制备的催化剂，同时催化剂的氧吸附量和噻吩吸附热也最大。