Kinetic features of ethylene polymerization over supported catalysts [2,6‐bis(imino)pyridyl iron dichloride/magnesium dichloride] with AlR3 as an activator

The effects of polymerization temperature, polymerization time, ethylene and hydrogen concentration, and effect of comonomers (hexene‐1, propylene) on the activity of supported catalyst of composition LFeCl₂/MgCl₂‐Al(i‐Bu)₃ (L = 2,6‐bis[1‐(2,6‐dimethylphenylimino)ethyl] pyridyl) and polymer characteristics (molecular weight (MW), molecular‐weight distribution (MWD), molecular structure) have been studied. Effective activation energy of ethylene polymerization over LFeCl₂/MgCl₂‐Al(i‐Bu)₃ has a value typical of supported Ziegler–Natta catalysts (11.9 kcal/mol). The polymerization reaction is of the first order with respect to monomer at the ethylene concentration >0.2 mol/L. Addition of small amounts of hydrogen (9–17%) significantly increases the activity; however, further increase in hydrogen concentration decreases the activity. The IRS and DSC analysis of PE indicates that catalyst LFeCl₂/MgCl₂‐Al(i‐Bu)₃ has a very low copolymerizing ability toward propylene and hexene‐1. MW and MWD of PE produced over these catalysts depend on the polymerization time, ethylene and hexene‐1 concentration. The activation effect of hydrogen and other kinetic features of ethylene polymerization over supported catalysts based on the Fe (II) complexes are discussed. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5057–5066, 2007     

Graphitic nanofillers in PMMA nanocomposites—An investigation of particle size and dispersion and their influence on nanocomposite properties

Mechanical, thermal, and electrical properties of graphite/PMMA composites have been evaluated as functions of particle size and dispersion of the graphitic nanofiller components via the use of three different graphitic nanofillers: “as received graphite” (ARG), “expanded graphite,” (EG) and “graphite nanoplatelets” (GNPs) EG, a graphitic materials with much lower density than ARG, was prepared from ARG flakes via an acid intercalation and thermal expansion. Subsequent sonication of EG in a liquid yielded GNPs as thin stacks of graphitic platelets with thicknesses of ～10 nm. Solution‐based processing was used to prepare PMMA composites with these three fillers. Dynamic mechanical analysis, thermal analysis, and electrical impedance measurements were carried out on the resulting composites, demonstrating that reduced particle size, high surface area, and increased surface roughness can significantly alter the graphite/polymer interface and enhance the mechanical, thermal, and electrical properties of the polymer matrix. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2097–2112, 2007     

Dibutyltin-3-hydroxyflavone titrates a dissociable component (cofactor) of mitochondrial ATP synthase: An energy-transfer component linked to the ubiquinone pool

Dibutyltin-3-hydroxyflavone, Bu₂Sn(of), is a new fluorescence probe inhibitor of F₁F₀-ATPase and oxidative phosphorylation which inhibits by titration of an unidentified component of F₀. Its site of action is closely related to that of the trialkyltins and of venturicidin. This F₀ component is part of a pool of this component which is present in the heart mitochondrial inner membrane at levels of 5–7 nmol (mg protein)^?1 [18 ± 3 Bu₂Sn(of) sites per mol F₁F₀-ATPase]. However, ATPase activity in submitochondrial particles is near maximally inhibited by titration of approx. three Bu₂Sn(of) sites per mol F₁F₀-ATPase. Over 60% (60–80%) of the Bu₂Sn(of) interaction sites can be lost during the purification of F₁F₀-ATPase from submitochondrial particles. The number of Bu₂Sn(of) interaction sites in various F₁F₀-ATPase preparations is variable. The high numbers of Bu₂Sn(of) sites per mol F₁F₀-ATPase for heart mitochondria (18–21) and submitochondrial particles (15–19.5) decline in ATP synthase (11–15) to the low values obtained in Complex V (7–10.5) and the minimal values observed in highly purified F₁F₀?ATPase (3.5–5.6), thus indicating a variable dissociable component or cofactor of ATP synthase. The Bu₂Sn(of) interaction site, a component of ATP synthase, is responsive to the redox status of the respiratory chain and the interaction with Bu₂Sn(of) is with the reduced form of this component. Fluorescence titration studies show that this component is in redox equilibrium with the ubiquinone pool of the respiratory chain. It is proposed that this redox component serves as an inhibitor titratable cofactor pool which cycles through an F₀ interaction site (or sites) via a system which serves as an energy-transfer link between the respiratory chain and ATP synthase.     

Deactivation reactions in the modeled 2,2,6,6‐tetramethyl‐1‐piperidinyloxy‐mediated free‐radical polymerization of styrene: A comparative study with the 2,2,6,6‐tetramethyl‐1‐piperidinyloxy/acrylonitrile system

The competitiveness of the combination and disproportionation reactions between a 1‐phenylpropyl radical, standing for a growing polystyryl macroradical, and a 2,2,6,6‐tetramethyl‐1‐piperidinyloxy (TEMPO) radical in the nitroxide‐mediated free‐radical polymerization of styrene was quantitatively evaluated by the study of the transition geometry and the potential energy profiles for the competing reactions with the use of quantum‐mechanical calculations at the density functional theory (DFT) UB3‐LYP/6‐311+G(3df, 2p)//(unrestricted) Austin Model 1 level of theory. The search for transition geometries resulted in six and two transition structures for the radical combination and disproportionation reactions, respectively. The former transition structures, mainly differing in the out‐of‐plane angle of the N? O bond in the transition structure TEMPO molecule, were correlated with the activation energy, which was determined to be in the range of 8.4–19.4 kcal mol^?1 from a single‐point calculation at the DFT UB3‐LYP/6‐311+G(3df, 2p)//unrestricted Austin Model 1 level. The calculated activation energy for the disproportionation reaction was less favorable by a value of more than 30 kcal mol^?1 in comparison with that for the combination reaction. The approximate barrier difference for the TEMPO addition and disproportionation reaction was slightly smaller for the styrene polymerization system than for the acrylonitrile polymerization system, thus indicating that a β‐proton abstraction through a TEMPO radical from the polymer backbone could diminish control over the radical polymerization of styrene with the nitroxide even more than in the latter system. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 232–241, 2007     

Molecular modeling study on surface,thermal, mechanical and gas diffusion properties of chitosan

The motivation of this work is to provide reliable and accurate modeling studies of the physical (surface, thermal, mechanical and gas diffusion) properties of chitosan (CS) polymer. Our computational efforts have been devoted to make a comparison of the structural bulk properties of CS with similar type of polymers such as chitin and cellulose through cohesive energy density, solubility parameter, hydrogen bonding, and free volume distribution calculations. Atomistic modeling on CS polymer using molecular mechanics (MM) and molecular dynamics (MD) simulations has been carried out in three dimensionally periodic and effective two dimensionally periodic condensed phases. From the equilibrated structures, surface energies were computed. The equilibrium structure of the films shows an interior region of mass density close to the value in the bulk state. Various components of energetic interactions have been examined in detail to acquire a better insight into the interactions between bulk structure and the film surface. MD simulation (NPT ensemble) has also been used to obtain polymer specific volume as a function of temperature. It is demonstrated that these V–T curves can be used to locate the volumetric glass transition temperature (T_g) reliably. The mechanical properties of CS have been obtained using the strain deformation method. Diffusion coefficients of O₂, N₂, and CO₂ gas molecules at 300 K in CS have been estimated. The calculated properties of CS are comparable with the experimental values reported in the literature. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1260–1270, 2007     

Melt rheology of polylactide/montmorillonite nanocomposites

In this article, the linear and nonlinear shear rheological behaviors of polylactide (PLA)/clay (organophilic‐montmorillonite) nanocomposites (PLACNs) were investigated by an Advanced Rheology Expanded System rheometer. The nanocomposites were prepared by master batch method using a twin‐screw extruder with poly(ε‐caprolactone) (PCL) as a compatibilizer. The presence of org‐MMT leads to obvious pseudo‐solid‐like behaviors of nanocomposite melts. The behaviors caused by the formation of a “percolating network” derived from the reciprocity among the strong related sheet particles. Therefore, the storage moduli, loss moduli, and dynamic viscosities of PLACNs show a monotonic increase with MMT content. Nonterminal behaviors exists in PLACNs nanocomposites. Besides the PLACNs melts show a greater shear thinning tendency than pure PLA melt because of the preferential orientation of the MMT layers. Therefore, PLACNs have higher moduli but better processibility compared with pure PLA. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3189–3196, 2007     

Adsorption of dicarboxylates on nano-sized gibbsite particles: effects of ligand structure on bonding mechanisms

The adsorption of the dicarboxylates o-phthalate, maleate, fumarate, malonate, and oxalate (representing ligands with the general composition ⁻O₂C---C_n---CO₂⁻; n=0, 1, or 2) on gibbsite were studied by means of quantitative batch adsorption experiments and attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy. The interpretations of ATR-FTIR spectra were aided by comparison with IR spectra of solution species and by results from theoretical frequency calculations. The main objectives of the study were to identify the molecular level bonding mechanisms of the dicarboxylates to gibbsite, and to investigate how these were influenced by the composition and structure of the ligands. Carboxylates with n=2 formed predominantly outer sphere complexes, whereas the importance of inner sphere complexes progressively increased for n=1 and 0. The inner sphere structures were identified as mononuclear chelates with one oxygen from each carboxylate group bonded to Al(III) at the surface. This showed the importance of chelate ring structure for the formation of inner sphere surface complexes, with stabilities of the complexes increasing in the order seven-membered ring less than six-membered ring less than five-membered ring. For ligands with n=2 only small variations in surface speciation were observed as a function of steric factors; irrespective of the relative positions of the carboxylate groups and bulkiness of the ligands outer sphere bonding is the dominating adsorption mode. Adsorption experiments were also conducted with gibbsite particles exhibiting differences in shape and surface roughness. These experiments showed that inner sphere complexes were favored on the less well-developed and more irregular gibbsite particles.     

Synthesis of grafted poly(p‐phenyleneethynylene) with energy donor–acceptor architecture via atom transfer radical polymerization: Towards nonaggregating and hole‐facilitating light‐emitting material

In this contribution, we demonstrate a new effective methodology for constructing highly efficient and durable poly(p‐phenyleneethynylene) (PPE) containing emissive material with nonaggregating and hole‐facilitating properties through the introduction of hole‐transporting blocks into the PPE system as the grafting coils as well as building the energy donor–acceptor architecture between the grafting coils and the PPE backbone. Poly(2‐(carbazol‐9‐yl)ethyl methacrylate) (PCzEMA), herein, is chosen as the hole‐transporting blocks, and incorporated into the PPE system as the grafting coils via atom transfer radical polymerization. The chemical structure of the resultant copolymer, PPE‐g‐PCzEMA, was characterized by NMR and gel permeation chromatography, showing that the desirable copolymer was obtained with the narrow polydispersity. The increased thermal stability of PPE‐g‐PCzEMA was confirmed by thermogravimetric analysis and differential scanning calorimetry along with its macroinitiator. The optoelectronic properties of this copolymer were studied in detail by ultraviolet‐visible absorption, photoluminescence emission and excitation spectra, and cyclic voltammogram (CV). The results indicate that PPE‐g‐PCzEMA exhibits the solid‐state luminescent property dominated by individual lumophores, and also the energy transfer process from the PCzEMA blocks to the PPE backbone with a relatively higher energy transfer efficiency in the solid‐state compared to that of the solution state. Additionally, the hole‐injection property is greatly facilitated due to the presence of PCzEMA, as confirmed by CV profiles. All these data indicate that PPE‐g‐PCzEMA is a good candidate for use in optoelectronic devices. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3776–3787, 2007