Shear banding in strained semicrystalline polyamide 6 films as revealed by atomic force microscopy: Role of the amorphous phase

Atomic force microscopy (AFM) has been used to visualize the plastic deformation mechanisms that are responsible for the yielding of semicrystalline polymers of low degree of crystallinity (<50%). Indeed, AFM, if operated in suitable conditions, is able to image both the amorphous and the crystalline phases. Polyamide 6 films have been drawn at temperatures T < 160 °C. Postmortem AFM observations show that, at yield, shear bands nucleate and propagate in the amorphous phase. They cross the crystalline lamellae and run over the whole surface of the sample. By crossing the lamellae, they form nanoblocks of uniform size. Neither the size of the nanoblocks nor the angle between the tensile axis and the shear bands can be explained in terms of crystal plasticity. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 687–701, 2004     

Mutual influence of the morphology and capillary rheological properties in nylon/glass‐fiber/liquid‐crystalline‐polymer blends

Nylon‐6/glass‐fiber (GF)/liquid‐crystalline‐polymer (LCP) ternary blends with different viscosity ratios were prepared with three kinds of nylon‐6 with different viscosities as matrices. The rheological behaviors of these blends were characterized with capillary rheometry. The morphology was observed with scanning electron microscopy and polarizing optical microscopy. This study showed that although LCP did not fibrillate in binary nylon‐6/LCP blends, LCP fibrillated to a large aspect ratio in some ternary blends after GF was added. The addition of 5 wt % LCP significantly reduced the melt viscosity of nylon‐6/GF blends to such an extent that some nylon‐6/GF/LCP blends had quite low viscosities, not only lower than those of neat resins and nylon‐6/GF blends but also lower than those of corresponding nylon‐6/LCP blends. The mutual influence of the morphology and rheological properties was examined. The great reduction of the melt viscosity was considered the result of LCP fibrillation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1619–1627, 2004     

Pressure and temperature dependence of the gas‐transport properties of dense poly[2,6‐toluene‐2,2‐bis(3,4‐dicarboxylphenyl)hexafluoropropane diimide] membranes

The gas‐transport properties of poly[2,6‐toluene‐2,2‐bis(3,4‐dicarboxylphenyl)hexafluoropropane diimide] (6FDA‐2,6‐DAT) have been investigated. The sorption behavior of dense 6FDA‐2,6‐DAT membranes is well described by the dual‐mode sorption model and has certain relationships with the critical temperatures of the penetrants. The solubility coefficient decreases with an increase in either the pressure or temperature. The temperature dependence of the diffusivity coefficient increases with an increase in the penetrant size, as the order of the activation energy for the diffusion jump is CH₄ > N₂ > O₂ > CO₂. Also, the average diffusion coefficient increases with increasing pressure for all the gases tested. As a combined contribution from sorption and diffusion, permeability decreases with increases in the pressure and the kinetic diameter of the penetrant molecules. Even up to 32.7 atm, no plasticization phenomenon can be observed on flat dense 6FDA‐2,6‐DAT membranes from their permeability–pressure curves. However, just as for other gases, the absolute value of the heat of sorption of CO₂ decreases with increasing pressure at a low‐pressure range, but the trend changes when the feed pressure is greater than 10 atm. This implies that CO₂‐induced plasticization may occur and reduce the positive enthalpy required to create a site into which a penetrant can be sorbed. Therefore, a better diagnosis of the inherent threshold pressure for the plasticization of a glassy polymer membrane may involve examining the absolute value of the heat of sorption as a function of pressure and identifying the turning point at which the gradient of the absolute value of the heat of sorption against pressure turns from a negative value to a positive one. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 354–364, 2004     

RuH2和RuN2电子组态与光谱性质的从头计算

用量子化学从头算方法在B3LYP/6 311G 的水平上 ,研究了RuH2 和RuN2 可能的电子组态和光谱性质 .结果表明 ,RuH2 的3 B2 和5Σ-态对应于静电作用的物理吸附态 .RuN2 的一重态和三重态的计算结果跟钌单晶面上的实验值相接近 .而RuN2 在C∞v对称性时 ,五重态5Σ-的计算频率比实验值稍低 .在C2v对称性时 ,五重态的计算频率值则更低 ,3 B2 和5A1态不能稳定存在     

新型二硫纶·菲咯啉-5，6-二酮合铜(Ⅱ)配合物的磁性研究

报道了新合成的二氰基二硫纶·菲咯啉-5，6-二酮合铜(Ⅱ)配合物CuLL′(L=mnt^2-, 1,2-dicyano-1,2-ethylenedithiolate; L′=phen-5，6-dione, 1,10-phenanthroline-5,6-dione)的变温磁化率和电子顺磁共振波谱表征结果. 发现微晶粉体型的标题配合物CuLL′具有一定的顺磁性，形成四配位的近似于方形的结构. 探讨了这种配合物磁学特性与结构的关系.     

The First Intramolecular Charge Transfer Transition Based on 2-Ureido-4[1H]-pyrimidinone Binding Module

The first intramolecular charge transfer transition based on 2-ureido-4[1H]-pyrimidinone binding module was reported.     

Solid Phase Synthesis of 2-Substituted 1,3-Oxazin-6-ones Using Resin-bound Cyclic Malonic Acid Ester

A facile solid phase synthesis of 2-substituted 1,3-oxazin-6-ones using polymer-supported Meldrum‘s acid has been reported. Reaction of the resin-bound cyclic malonic acid ester with triethyl orthoformate and subsequent double substitution with amide, afforded the corresponding polymer-supported acylaminomethylene cyclic malonic acid ester, which upon thermal treatment led to 1, 3-oxazin-6-ones in good yields and with high purity.     

Influence of the sample orientation in Sn<Subscript>2</Subscript>P<Subscript>2</Subscript>S<Subscript>6</Subscript> crystals on the hydrostatic piezoelectric coefficients

The influence of the sample orientation on the effective value of the hydrostatic piezoelectric coefficients d _h ⁽ⁱ⁾ of Sn₂P₂S₆ crystals has been studied. The hydrostatic piezoelectric coefficients d _h ⁽¹⁾ and d′ _h ⁽³⁾ , were measured, d _h ⁽¹⁾ =(244±3) pC/N and d′ _h ⁽³⁾ =(92±1) pC/N. The hydrostatic piezoelectric coefficient d _h ⁽³⁾ for orthogonal axis system was calculated to be d _h ⁽³⁾ =(87±2) pC/N. The, optimal orientation of the sample has been found as (Xy l)−20°-cut. Maximal value of the effective hydrostatic piezoelectric coefficient d _h ⁽¹⁾ equals 260 pC/N. Double rotated samples were also studied. The orientation of the samples insensitive to the pressure has been found. The theoretical mean value of hydrostatic piezoelectric coefficient (d _h ) _mean corresponding to randomly oriented Sn₂P₂S₆ grains in a poled composite has been calculated to be (d _h ) _mean =136 pC/N.