Synthesis of functional polymers—Vinylidene fluoride based fluorinated copolymers and terpolymers bearing bromoaromatic side‐group

The radical co‐ and terpolymerization of 4‐[(α,β,β‐trifluorovinyl)oxy]bromo benzene (TFVOBB) with 1,1‐difluoroethylene (or vinylidene fluoride, VDF, or VF₂), hexafluoropropene (HFP), perfluoromethyl vinyl ether (PMVE), and chlorotrifluroroethylene (CTFE) is presented. Although TFVOBB could be thermocyclodimerized, it could not homopolymerize under radical initiation. TFVOBB could be copolymerized in solution under a radical initiator with VDF or CTFE comonomers, while its copolymerization with HFP or PMVE were unsuccessful. The terpolymerization of TFVOBB with VDF and HFP, or VDF and PMVE, or VDF and CTFE also led to original fluorinated terpolymers bearing bromoaromatic side‐groups. The conditions of co‐ and terpolymerization were optimized in terms of the nature of the radical initiators, and of the nature of solvents (fluorinated or nonhalogenated). Various monomer concentrations in the co‐ and terpolymers were assessed by ¹⁹F and ¹H‐NMR spectroscopy. The thermal and physico chemical properties were also studied. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5077–5097, 2004     

Influence of concentration on the activation energy for diffusion in polymer-solvent systems

The self-diffusion of benzene, toluene, and ethylbenzene in polystyrene have been analyzed using the Vrentas/Duda free-volume diffusion model. Diffusion coefficient predictions suggest an exponential concentration dependence of the activation energy required to overcome attractive forces, E. Without the use of any diffusion data approximating E as zero over the entire concentration range yields self-diffusion coefficient predictions which are in good agreement with experimental data. © 1992 John Wiley & Sons, Inc.     

A Simple Chaotic Circuit with Impulsive Switch Depending on Time and State

This paper presents a simple chaotic circuit consisting of two capacitors, one linear two-port VCCS and one time-state-controlled impulsive switch. The impulsive switch causes rich chaotic and periodic behavior. The circuit dynamics can be simplified into a one-dimensional return map that is piecewise linear and piecewise monotone. Using the return map, we clarify parameter conditions for existence of chaotic and periodic attractors and coexistence state of attractors.     

Synthesis and copolymerization of new phosphorus‐containing acrylates

Two phosphorus‐containing acrylate monomers were synthesized from the reaction of ethyl α‐chloromethyl acrylate and t‐butyl α‐bromomethyl acrylate with triethyl phosphite. The selective hydrolysis of the ethyl ester monomer with trimethylsilyl bromide (TMSBr) gave a phosphonic acid monomer. The attempted bulk polymerizations of the monomers at 57–60 °C with 2,2′‐azobisisobutyronitrile (AIBN) were unsuccessful; however, the monomers were copolymerized with methyl methacrylate (MMA) in bulk at 60 °C with AIBN. The resulting copolymers produced chars on burning, showing potential as flame‐retardant materials. Additionally, α‐(chloromethyl)acryloyl chloride (CMAC) was reacted with diethyl (hydroxymethyl)phosphonate to obtain a new monomer with identical ester and ether moieties. This monomer was hydrolyzed with TMSBr, homopolymerized, and copolymerized with MMA. The thermal stabilities of the copolymers increased with increasing amounts of the phosphonate monomer in the copolymers. A new route to highly reactive phosphorus‐containing acrylate monomers was developed. A new derivative of CMAC with mixed ester and ether groups was synthesized by substitution, first with diethyl (hydroxymethyl)phosphonate and then with sodium acetate. This monomer showed the highest reactivity and gave a crosslinked polymer. The incorporation of an ester group increased the rate of polymerization. The relative reactivities of the synthesized monomers in photopolymerizations were determined and compared with those of the other phosphorous‐containing acrylate monomers. Changing the monomer structure allowed control of the polymerization reactivity so that new phosphorus‐containing polymers with desirable properties could be obtained. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2207–2217, 2003     

Solution 1H and 13C NMR of new chiral 1,4‐oxazepinium heterocycles and their intermediates from the reaction of 2,4‐pentanedione with α‐L‐amino acids and (R)‐(—)‐2‐phenylglycinol

The reaction of 2,4‐pentanedione ( 1 ) with (R)‐(—)‐2‐phenylglycine methyl ester ( 2 ), (R)‐(—)‐2‐phenylglycinol ( 3 ) and the proteinogenic amino acids (2S,3R)‐(—)‐2‐amino‐3‐hydroxybutyric acid (L ‐threonine) ( 4 ) and (R)‐(—)‐2‐amino‐3‐mercaptopropionic acid (L ‐cysteine) ( 5 ) methyl esters was investigated. The corresponding enamines 6 , 7 and 8 were isolated and characterized spectroscopically whereas 9 , which is unstable, was transformed in situ into 13 . Treatment of 7 , 8 and 9 with boron trifluoride etherate afforded the new [1,4]oxazepines 10 , 11 and [1,4]thiazepine ( 12 ) as their BF₃O^? salts. The structures of the enamines and their corresponding seven‐membered heterocycles were assessed by 1D and 2D NMR spectroscopy. Variable‐temperature experiments revealed different molecular mobility behavior among these heterocycles. Copyright © 2003 John Wiley & Sons, Ltd.     

Formation of β‐iPP in isotactic polypropylene/ethylene–propylene rubber blends: Effects of preparation method,composition, and thermal condition

The effects of preparation method, composition, and thermal condition on formation of β‐iPP in isotactic polypropylene/ethylene–propylene rubber (iPP/EPR) blends were studied using modulated differential scanning calorimeter (MDSC), wide angle X‐ray diffraction (WAXD), and phase contrast microscopy (PCM). It was found that the α‐iPP and β‐iPP can simultaneity form in the melt‐blended samples, whereas only α‐iPP exists in the solution‐blended samples. The results show that the formation of β‐iPP in the melt‐blended samples is related to the crystallization temperature and the β‐iPP generally diminishes and finally vanishes when the crystallization temperature moves far from 125 °C. The phenomena that the lower critical temperature of β‐iPP in iPP/EPR obviously increases to 114 °C and the upper critical temperature decreases to 134 °C indicate the narrowing of temperature interval, facilitating the formation of β‐iPP in iPP/EPR. Furthermore, it was found that the amount of β‐iPP in melt‐blended iPP/EPR samples is dependent on the composition and the maximum amount of β‐iPP formed when the composition of iPP/EPR blends is 85:15 in weight. The results through examining the effect of annealing for iPP/EPR samples at melt state indicate that this annealing may eliminate the susceptibility to β‐crystallization of iPP. However, only α‐iPP can be observed in solution‐blended samples subjected to annealing for different time. The PCM images demonstrate that an obvious phase‐separation happens in both melt‐blended and solution‐blended iPP/EPR samples, implying that compared with the disperse degree of EPR in iPP, the preparation method plays a dominant role in formation of β‐iPP. It is suggested that the origin of formation of β‐iPP results from the thermomechanical history of the EPR component in iPP/EPR. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1704–1712, 2007     

The influence of hard‐segments on two‐phase structure and shape memory properties of PCL‐based segmented polyurethanes

Poly(ε‐caprolactone)‐based segmented polyurethanes (PCLUs) were prepared from poly(ε‐caprolactone) diol, diisocyanates (DI), and 1,4‐butanediol. The DIs used were 4,4′‐diphenylmethane diisocyanate (MDI), 2,4‐toluenediisocyanate (TDI), isophorone diisocyanate (IPDI), and hexamethylene diisocyanate (HDI). Differential scanning calorimetry, small‐angle X‐ray scattering, and dynamic mechanical analysis were employed to characterize the two‐phase structures of all PCLUs. It was found that HDI‐ and MDI‐based PCLUs had higher degree of microphase separation than did IPDI‐ and TDI‐based PCLUs, which was primarily due to the crystallization of HDI‐ and MDI‐based hard‐segments. As a result, the HDI‐based PCLU exhibited the highest recovery force up to 6 MPa and slowest stress relaxation with increasing temperature. Besides, it was found that the partial damage in hard‐segment domains during the sample deformation was responsible for the incomplete shape‐recovery of PCLUs after the first deformation, but the damage did not develop during the subsequent deformation. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 557–570, 2007     

MgO films grown on yttria-stabilized zirconia by molecular beam epitaxy

MgO films were grown on (0 0 1) yttria-stabilized zirconia (YSZ) substrates by molecular beam epitaxy (MBE). The crystalline structures of these films were investigated using X-ray diffraction and transmission electron microscopy. Growth temperature was varied from 350 to 550 °C, with crystalline quality being improved at higher temperatures. The MgO films had a domain structure: (1 1 1)[1 1 2¯]_MgO(0 0 1)[1 0 0]_YSZ with four twin variants related by a 90° in-plane rotation about the [1 1 1]_MgO axis. The observed epitaxial orientation was compared to previous reports of films grown by pulsed laser deposition and sputtering and explained as resulting in the lowest interface energy.     

Geometry and electronic structure of a heterometallic cluster Mo<Subscript>2</Subscript>Mg<Subscript>2</Subscript> in different oxidation states of Mo: a DFT study

Reduction of tetranuclear heterometallic complex Mo₂Mg₂ was simulated using the B3LYP and PBE density functional methods. The results of geometry calculations of the initial complex [Mo^VIO₂Mg(MeOH)₂(OMe)₄]₂ and a partially reduced Mo^V complex are in good agreement with experimental data. The reduced Mo^III complex is characterized by a decrease in the binding energy of aqua ligands. Structural rearrangement of the complex with release of a coordination position at the Mo atoms requires small energy expenditure. One can assume that the reduction of the polynuclear complex causes overcrowding of its coordination sphere, which favors formation of dinitrogen complexes. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 3, pp. 441–457, March, 2008.     

Crystallographic report: Crystal structure of tetra(4‐methyl‐5‐imidazole‐carboxyaldehyde)zinc(II) diperchlorate

The central zinc(II) atom in the title complex is tetrahedrally coordinated by four nitrogen atoms derived from 4‐methyl‐5‐imidazolecarboxyaldehyde ligands with Zn? N in the range 2.007(3) to 2.026(4) Å. Copyright © 2003 John Wiley & Sons, Ltd.