Yb:FAP和Yb:C_3S_2-FAP晶体光谱的温度特性和选择激发

报导了Yb :FAP和Yb :C3S2 _FAP晶体在不同温度下的吸收光谱和荧光光谱实验结果 ,研究发现由于电子_声子近共振耦合作用 ,Yb :FAP和Yb :C3S2 _FAP晶体均存在有明显的振动谱 ,Yb :FAP晶体的零声子线在低温下还劈裂为相差 10cm- 1 的两条线 .采用激光选择激发技术研究了Yb3 离子在FAP和C3S2 _FAP晶体中的格位特征 ,结果表明Yb3 离子在这两种基质中都只占据Ca(Ⅱ )格位 ,但由于CaF2 的挥发 ,导致了Ca(Ⅱ )格位的局部畸变 .     

光纤光栅选频掺Yb3+双包层光纤激光器

利用相位掩模法 ,在D形内包层掺Yb3 双包层光纤一端直接写制出Bragg光栅 ,用作双包层光纤激光器的输出腔镜 .试验得到了线宽为 0 196nm ,波长为 10 5 8 2nm ,最高输出功率为 5 70mW的稳定激光输出 ,解决了激光器中模式竞争造成的输出不稳定现象 .从速率方程出发 ,对激光器的输出功率与抽运功率、光栅反射率的关系以及最佳光纤长度进行了理论分析 ,结果与实验符合很好     

Cl/HN3/I2全气相化学激光体系的化学动力学模拟计算

 对Cl/HN₃/I₂产生NCl(a)/I激光的过程进行了化学动力学计算，主要考察了Cl,HN₃和I₂的初始粒子数密度及其配比对小信号增益系数的影响。结果发现,当温度为400K, 初始Cl粒子数密度为1×10¹⁵，1×10¹⁶和1×10¹⁷cm^-3时,小信号增益系数分别达到1.6×10^-4,1.1×10^-3和1.1×10^-2cm^-1，获得最佳小信号增益系数的HN₃和I₂的初始粒子数密度分别为初始Cl粒子数密度的1～2倍和2%～4%。同时，对Cl，HN₃和I₂配比对小信号增益系数和增益持续时间的影响进行了讨论。     

含氮类金刚石薄膜的紫外辐照研究

 用射频等离子体方法在玻璃基底上制备的类金刚石（DLC）薄膜，采用离子注入法掺氮，并对掺氮DLC薄膜紫外（UV）辐照前后的性能变化进行了研究。研究结果表明：随氮离子注入剂量及UV辐照时间的增加，位于2 930cm^-1附近的SP ³C-H吸收峰明显变小，而位于1 580cm^-1附近的SP2C-H吸收峰则明显增强，薄膜的电阻率明显呈下降趋势；随UV辐照时间的增加，位于1 078cm^-1附近的Si-O-Si键数量及位于786cm^-1附近的Si-C键数量明显增加。即氮离子注入和UV辐照明显改变了DLC薄膜的结构与特性。     

Synthesis and characterization of N-3-phenyl-2-propenoyl amino acids

Three N-3-phenyl-2-propenoyl amino acids were synthesized through interaction between 3-phenyl-2-propenoyl chloride and amino acids in alkaline with a high Yield.Structure of the products were identified by elemental analysis,IR and NMR spectroscopy.     

CATALYSIS OF POLYSTYRENE N-HYDROXYL SULFONAMIDE FOR ESTERIFICATION OF BUTANOL WITH ACETIC ANHYDRIDE

1. INTRODUCTION The development of efficient polymer-supported catalysts has attracted much attention [1]. For obtaining polymeric catalysts, catalytically active groups were introduced onto polymers mostly by copolymerization of the appropriate monomers bearing the desired catalyticfunctionalities (e.g. imidazole, OH, and COOH) or by modification of preformed polymers.Another possibility involves the attachment of side chains, containing the desired arrangement of functional groups, o…     

Acetalation and Ketalation Catalyzed by SO42-/TiO2-MoO3

The catalytic activities of SO42-/TiO2-MoO3 in synthesizing cyclohexanone ethylene ketal,cyclohexanone 1,2-propanediol ketal, 2-propyl-1,3-dioxolane, 4-methyl-2-isopropyl-1,3-dioxolane,2-isopropyl-1,3-dioxolane, 4-methyl-2-isopropyl-1,3-dioxolane, butanone ethy-lene ketal and butanone 1,2-propanediol ketal were reported. It has been demonstrated that SO42-/TiO2-MoO3 is an excellent catalyst. Various factors concerned in this reaction have been investigated. The optimum conditions have been found, that is, the molar ratio of aldehyde/ketone to alcohol was 1:1.5 or 1:1.3,the mass ratio of the catalyst used to the reactants was 0.25～1.5%, and the reaction time was 45～60 min. Under this conditions, the yield of cyclohexanone ethylene ketal is 82.7%, cyclohexanone 1,2-propanediol ketal is 83.4%, the yield of 2-propyl-1,3-dioxolane is 68.1%,4-methyl-2-isopropyl-1,3-dioxolane is 87.5%, the yield of 2-isopropyl-1,3-dioxolane is 70.7%,4-methyl-2-isopropyl-1,3-dioxolane is 82.5%, the yield of butanone ethylene ketal is 74.1%, and butanone 1,2-propanediol ketal is 94.9%.Some equation and experiment results concerned of the synthetic acetals or ketals were listed as follows.     

Synthesis of 2-Acyl-2H-1,2,3-diazaphospholes and Their Diels-Alder Reaction with Cyclopentadiene

2H-1,2,3-Diazaphospholes 3a-3h were prepared from various ketone acylhydrazones and phosphorus trichloride in the presence of triethylamine. Compounds 3 underwent feasible hetero-Diels-Alder reactions with cyclopentadiene to afford the respective anellated [1,2,3]diazaphospholes 4a--4d as well as 4a‘--4d‘ in moderate yields. The endo rule in the reaction was observed under kinetic control conditions.     

Regioselective Synthesis of Multi-substituted Phenylselenomethyl Isoxazolines

A mild, regioselective 1, 3-dipolar cycloaddition protocol for the preparation ofphenylselenomethyl isoxazolines through substituted allyl phenyl selenides and nitrile oxides wasreported.     

Solid Phase Synthesis of 2-Substituted 1,3-Oxazin-6-ones Using Resin-bound Cyclic Malonic Acid Ester

A facile solid phase synthesis of 2-substituted 1,3-oxazin-6-ones using polymer-supported Meldrum‘s acid has been reported. Reaction of the resin-bound cyclic malonic acid ester with triethyl orthoformate and subsequent double substitution with amide, afforded the corresponding polymer-supported acylaminomethylene cyclic malonic acid ester, which upon thermal treatment led to 1, 3-oxazin-6-ones in good yields and with high purity.