新显色剂1-羟基-2-(5-NO2-2-吡啶偶氮)-8-氨基-3,6-萘二磺酸与铜显色反应的研究

探讨了新显色剂 1-羟基-2-(5-NO2-2-吡啶偶氮)-8-氨基-3,6-萘二磺酸(简称5-NO2-PAH)与铜离子显色的适宜条件及其共存离子的影响,建立了 5-NO2-PAH测定铜的新显色反应体系.在 pH 7.0～10.0 范围内,铜与试剂形成稳定的 1∶2 配合物,其最大吸收峰位于 653 nm, 表观摩尔吸光系数εCu=4.68×104 L·mol-1·cm-1,铜的浓度在 0 μg/10 mL～14 μg/10 mL 范围内遵守比尔定律.方法已用于合金中铜的测定.     

层状正极材料LiNi1/6Co1/6Mn2/3O2的制备及电池性能

0引言为解决目前日益严重的汽车尾气排放对城市空气造成污染问题,作为绿色能源的锂离子电池已成为动力电池的首选对象。国际上,高容量、大功率锂离子电池早于1995年已开始研制。1996年,我国天津电源研究所也进行了大容量锂离子蓄电池及电池组的探索[1]。目前,锂离子电池的正极材料是制约其大规模推广应用的关键。现研究的正极材料主要包括具有层状结构的LiCoO2,LiN iO2和LiM nO2及具有尖晶石结构的LiM n2O4等。其中LiC oO2作为目前唯一已经商业化的正极材料具有理论容量高、可循环性能好等优点,但因Co资源的相对缺乏导致其价格高昂。…     

KF-alumina 催化下2-氨基-4-芳基-5,6-二氢化-4H-吡喃[3,2-c]喹啉-5-酮-3-羧酸酯衍生物的一步合成

以芳醛、氰乙酸酯和4-羟基喹啉-2-酮为原料, 乙醇为溶剂, 在KF-Al₂O₃催化下80 ℃, 一步合成了2-氨基-4-芳基-5,6-二氢化-4H-吡喃[3,2-c]喹啉-5-酮-3-羧酸酯衍生物, 和其它方法相比, 具有反应条件温和, 容易操作和产率高等优点, 产物4a的结构通过X单晶衍射分析确证.     

Synthesis and Crystal Structure of Ethyl 5-Amino-1-[（5′-methyl-1′- t-butyl-4′-pyrazolyl）carbonyl]-3-methylthio-1H-pyrazole-4-carboxylate

1INTRODUCTIONPolarizedketenedithioacetalshavebeenex-tensivelyusedasbuildingblocksinorganicsyn-thesis,especiallyinthesynthesisofheterocycliccompounds[1～6].Pyrazoleanditsderivativesrepre-sentoneofthemostactiveclassesofcompoundspossessingwidespectraofbiologicalactivities.Overthepastfewyears,considerableevidenceshavebeenaccumulatedtodemonstratetheefficacyofpyrazolederivatives,suchasantibacterial[7],fun-gicidal[8],herbicidal[9],insecticidal[10]andotherbiologicalactivities[11,12].Uptonow,alarg…     

高温固相法合成LiNi1/3Mn1/3Co1/3O2及其性能研究

采用高温固相法合成出层状锂离子电池正极材料LiNi_1/3Mn_1/3Co_1/3O₂。通过XRD、ICP、SEM和电化学测试手段对产物的结构、组成、形貌及电化学性能进行了研究。XRD结果表明此方法合成的LiNi_1/3Mn_1/3Co_1/3O₂具有标准的α-NaFeO₂型层状结构，SEM照片显示颗粒粒径大约在500 nm左右，粒径分布较窄。以20 mA·g^-1电流密度放电，充放电电压在2.8～4.4 V之间，其首次放电比容量为170 mAh·g^-1，40次循环容量保持率为85.3%。进一步加入石墨导电剂后，同样条件下首次放电比容量变为179 mAh·g^-1，50次循环容量保持率为89.6%。容量衰减主要发生在前10次循环。XRD和SEM测试表明循环初期容量衰减的原因是由材料本体结构变化和界面反应共同作用的结果。     

Structural evolution of (Ca0.35Sr0.65)TiO3 perovskite at high pressures

Lattice parameters of a synthetic powder sample of Ca_0.35Sr_0.65TiO₃ perovskite have been determined by the method of Le Bail refinement, using synchrotron X-ray diffraction patterns collected at pressures up to 15.5 GPa with a membrane-driven diamond anvil cell. At ambient conditions, diffraction data were consistent with the I4/mcm structure reported previously in the literature for the same composition. Diffraction data collected at high pressures were consistent with tetragonal (or, at least, pseudo-tetragonal) lattice geometry, and no evidence was found for the development of any of the orthorhombic structures identified in other studies of (Ca, Sr)TiO₃ perovskites. Additional weak reflections, which could not be accounted for by the normal I4/mcm perovskite structure, were detected in diffraction patterns collected at pressures of 0.9-2.5 GPa, and above ∼13.5 GPa, however. Small anomalies in the evolution of unit cell volume and tetragonal strain were observed near 3 GPa, coinciding approximately with breaks in slope with increasing pressure of bulk and shear moduli for a sample with the same composition which had previously been reported. The anomalies could be due either to new tetragonal↔tetragonal/pseudo-tetragonal phase transitions or to subtle changes in compression mechanism of the tetragonal perovskite structure.     

Conformational Transformation Exhibited by the Peptide Extracted from Crystalline Region of Bombyx mori Silk Fibroin in Solid and Solution States

The conformational transformation of a 30-residue peptide H（Ala-Gly-Ser-Gly-AIa-Gly）5OH, i.e., （AGSGAG）5, extracted from highly crystalline region of Bombyx mori （B. mori） silk fibroin was described by using the high resolution solid state 13^C NMR, and CD spectroscopies. Based on the conformation-dependent 13^C NMR chemical shifts of the Ala, Gly and Ser residues and the line-shape analysis of the conformation sensitive Ala Cβ resonance, the peptide revealed a strong preference for silk Ⅱ structural form, i,e,, an antiparallel fl-sheet structure （φ= - 140±20°and ψ= 135±20°） in solid state. On the contrary, the CD spectra of this peptide in the two non-native hexafluorinated fibre spinning solvents, hexafluoroisopropanol （HFIP） and hexafluoroacetone （HFA）, exhibited the existence of an unusual tightly-folded conformation resembling 310-helix （φ=- 60±20° and ψ=-30±20°）, as judged from the R ratio of [θ]222/[θ]203 in HFIP solution, whereas a dynamically averaged unordered structure in HFA, Taken together, the information inclined to hypothesis that the primary structure of the highly crystalline regions of B. mori silk fibroin may be easily accessible to the large conformational changes, which in turn may be critical for facilitating the structural transformation from unprocessed silk fibroin （silk I form） to processed silk fiber （silk Ⅱform）.     

Photochromic dihetarylethenes. 18. New approach to the synthesis of dithienothiophene and preparation of its photochromic derivative

A new approach to the synthesis of dithienothiophene was developed, and 1,2-bis(2,6-dimethyldithieno[3,2-b;2",3"-d]thiophen-3-yl)hexafluorocyclopent-1-ene was prepared. The latter compound is the first representative of photochromic dihetarylethenes with the fused tricyclic fragments linked through the perfluorocyclene bridge.     

Theoretical study of endohedral metallofullerenes: Sc3−nLanN@C80 (n=0–3)

To provide theoretical insight into the structures and properties of Sc₃N@C₈₀, which has been isolated in high yield and purity as a new stable endohedral metallofullerene, density functional calculations are carried out for the Sc_3?nLa_nN@C₈₀ (n=0–3) series. Because of electron transfer from Sc₃N to C₈₀, the electronic structure of Sc₃N@C₈₀ is formally described as (Sc₃N)⁶⁺C$_{80}^{6-}$. The encapsulated Sc₃N cluster takes a planar structure with long Sc–Sc distances and is highly stabilized inside the I_h cage of C₈₀, which rotates rapidly. As the number of La atoms increases, the Sc_3?nLa_nN cluster is forced to maintain a pyramidal structure in Sc_3?nLa_nN@C₈₀. In addition, the C₈₀ cage takes an open‐shell electronic structure due to an increase in the number of electrons transferring from Sc_3?nLa_nN. These make the endohedral structure less stable and more reactive. © 2001 John Wiley & Sons, Inc. J Comput Chem 22: 1353–1358, 2001     

Improvement of the Pd/Al2O3 Catalyst by the Control of the Sol-Gel Preparative Parameters

In this work, the metal dispersion of the Pd/Al₂O₃ catalyst prepared by sol-gel method is improved by an adequate optimisation of the preparative variables. First, the gelation temperature and the ageing time are selected, in order to avoid the reduction of the metal precursor (palladium acetylacetonate, Pd(acac)₂) by the solvent (sec-butanol, sB). The metal sintering effect on the catalysts treated in oxygen at 500°C is then minimized when the alumina pore size is controlled by the variation of the alumium alkoxide (AsB) concentration and the acetic acid amount ([AcA]/[AsB]). The appearance of new palladium particles on the alumina surface and the matching between the particle diameters and the pore sizes were also effective for the metallic surface area improvement on the samples treated in oxygen at 800°C. Compared to the reference catalysts, the higher metal dispersion obtained on the sol-gel ones was the determinant factor for their higher catalytic activity in methane combustion.